lets-talk-philkas-blog

[lets-talk-philkas-blog]

Build Your New Home With Natural Wood Cedar Garage Doors

Natural wood garage doors are aesthetically very pleasing and add value to any home. Redwood, oak and cedar garage doors are very popular with many new home builders. Natural wood is really great at accenting your home. In terms of garage doors pricing wood  doors are relatively cheap to build and install however they are obviously not as durable as conventional metal or composite garage doors.

Wood garage doors will weather quickly and expand and contract with temperature and humidity changes. As such frequent up keep will be required to keep them in good condition. Many of the new wood care products do a very good job of protecting wood products including wood garage doors. If you live in area with long winters and deep snows where the snow will lay against the doors for an extended period then you will need to conduct maintenance more often. Also if you live in an area with long periods of heat and humidity such as the Southeast US you will also have to do a good job of regular maintenance to protect your investment in doremi garage door repair burnsville.

The lowest priced wood garage doors are constructed of redwood while oak and cedar garage doors are normally about twice as expensive. A 16 x 7 redwood garage door will average about $600 to $800 depending on the type of door construction. Tilt-up garage doors are especially adaptable to using wood for construction. Cedar garage doors have an additional advantage of being lightweight and very rot resistant. In addition white cedar garage doors do a fairly good job of insulating as well.

If you decide to use a flush fit roll up garage door construction you should make sure the panels are constructed of one solid piece of wood. Failure to do so will mean that there is a good chance that glued and stapled seams will begin to show after weathering. Finding redwood and cedar material that is straight and clean can be expensive. Thin wood panels will have a higher risk of warping than larger dimensions. However it you are installing an oak door with long solid panels then door weight may become a concern.

For obvious reason you would not want to install cedar garage doors or any wood door in areas of high wind risk. However you can apply a wood door covering to a high wind rated door that will protect your home from hurricanes and meet local high wind building codes. In some case local building codes will not permit the modification. It probably be best find a conventional high wind garage door manufacture that has a very good artificial wood finish embossed on it if you live along the Southeast Coastal areas.

When building your home there is no doubt that natural wood garage doors do look very nice. The look of an oak, redwood or white cedar garage doors that are well maintained will certainly enhance the value of your home. It really is hard to beat the natural look of real wood.

Article Source: http://EzineArticles.com/1576640

[lets-talk-philkas-blog]

How to Replace Your Garage Door Repair Wheaton IL Torsion Springs

Many of my colleagues implored me not to write this article. In fact, some downright told me it was stupid. There is a stigma throughout the garage door service industry that you shouldn't deal with the replacement of your door's torsion springs unless you're a highly certified professional. I, however, know that there are many Do-It-Yourselfers out there that are more than competent for such complicated tasks. That's not to say that it isn't extremely dangerous. Torsion springs are under such immense pressure that if mishandled, they have the ability to maim and kill the repairman. That's why I believe I needed to write this instruction. At the very least, you'll understand what you're getting yourself into before you engage in this risky, but equally rewarding piece of home maintenance.

Before you get started, you need know what kind of springs you're dealing with. Torsion springs are located above the door and work together as a pair, providing a smoother and more even operation. They come in many gauges specific to the size and weight of your door and offer more control over the door when raising and lowering. Even though torsion springs are much safer when they break, they are much more dangerous to replace. I honestly recommend hiring a garage door repair Wheaton IL service technician to replace these. But, for all of you competent people out there that are willing to risk it, I'll tell you how to do it.

Now I'll explain the process for changing out your torsion springs. Let me just reiterate that this is a hazardous job; and that if you're not an engineer or otherwise mechanically inclined, you should go ahead and get someone to do it for you. Or at least have someone walk you through it in person. To perform this piece of maintenance, you'll need a ladder, a couple of C-clamps, replacement springs and a wrench. Now, torsion springs come in a variety of sizes and gauges. You'll need to find out what size your garage door unit needs and get them because tightening an incorrectly sized spring won't make up for it being weaker. Conversely, if it's too large, it simply won't fit the other components of your unit.

   First you need to mark the cables with a permanent marker. There are drums on either side of your garage door that contain spools which the cable wraps and unwraps around every time you use your door. If the cables are still tight, mark a spot on the drum and the cable to align them later. If they're loose, pull them into place before marking them. DO NOT touch the drum or the cable with your hands. The spring may break and cause you serious injury.    There are two winding bars that are used to wind the spring. They're about a foot and a half long, made of steel or iron and should fit snugly into the holes of the winding cone so they have maximum leverage. The winding cone is located on the bar above the door, on the end of the spring. The bars should not be worn on the ends and shouldn't easily slip out of the winding cone. If the bars can move more than 1 inches while inserted into the cone, you need new bars. Mark the bars while they are inserted to see if they slip out.    Put a bar into a hole on the winding cone. Keep your grip tight. Use an open-ended wrench to loosen the set screws. This will place the spring tension on the bar, so hold tightly. Keeping the bar in the winding cone, rotate the cone to loosen the spring. If you meet any resistance, a set screw may need to be loosened further. Do not take your hand off the bar. If the cone will not unwind at all, replace the set screws and call a professional.    After the cone is loose, continue rotating the cone until the spring is unwound. Insert the second bar on the first has been rotated downward. Repeat the previous steps on the other side.    Once the springs have been safely unwound, remove the bolts that hold the stationary torsion cones in place. The stationary cones are located on the other end of the springs near the center of the door. After you've removed them from the center, slide the springs to the side of the door on either end.    Now remove the screw sets on the cable drum and take the cable off. Do the same to the other side. After you've done that, loosen the cable drums from the bearing plate they're affixed to. This should make the pole that holds the springs be able to slide side to side. Go to the right side of the door and push the pole past the bracket holding it. This will pull it free on the left side and make it possible to remove the left side spring and insert the new one. Before replacing the spring, remove the cable drum. After replacing the spring, put the cable drum back on the pole and repeat this action on the opposite side.    Make sure the springs are on the correct side by looking at the end nearest the winding cone. The end of the coil should point up and the winding cone should be away from the center. Once this is done, slid the springs to the center cone.    Almost there. Put the drums back into position and re-bolt all of the hardware. Use your cable markings to gauge where the cable drums should be placed. Tighten the set screws on the drums; then tighten them one more half turn with a wrench. Put the cable back into the slot on the drum and pull the cable to the outer edge. Tighten the pole to remove the slack. Now, attach the springs to the center cone.    Using the same bars you used to unwind the springs, wind them in the opposite direction. Remember that the bar is taking the force of the springs until the cone is set in place. Hold your grip firmly. The springs will get longer as they're wound. If they do not expand, they're not put on right. Your standard 7 foot door needs 30 quarter turns to achieve tension. An 8 foot door requires 34 quarter turns. Once wound, replace the bolts with a wrench.    Mark the pole, with the spring on, about a quarter of an inch out from the spring. Put a bar in the bottom slot of the cone and turn it slightly away from the door. Now take the second bar and tap the bar in the slot while pulling the first bar toward the center of the door. This will set the cone in place. Keep tapping until the cone slides out to the marking. Once you hit the mark, pull the bar away from the door until it is at a 90 degree angle.    Last, just tighten the set screws until they reach the pole and then tighten them about another turn. Make sure to oil your springs so they more easily expand and contract.

Well done! You just completed one of the more difficult jobs in home repair and maintenance. Now all you have to do is go brag about it!

Article Source: http://EzineArticles.com/5147184

[lets-talk-philkas-blog]

Helpful Tips To Know The Ideal Time To Repair Your Garage Door

Garage doors are often the most overlooked part of any household. A number of US homeowners, in some of the major cities like Oahu and Pearl City, do not prefer even to spend a minute on checking their carport gates for possible damages. If these heavy structures are checked on a regular basis then it would help avoid any major technical defect in the future. It is also true that timely repairs can increase the life span of these gates.

Garage doors are used frequently. They have to move up and down numerous times in a single day. This would result in wear and tear of these heavy structures, so lack of proper repair may ultimately make these gates unusable. It is always better to hire a company which deals in garage door service to perform all the necessary repair work of your garage door. There are numerous parts of these heavy structures which may require repair. Here are some tips to understand when these parts may need a repair:

* Gate tracks: Since your garage door is frequently used, there are high chances that the tracks of these structures may get damaged. If the gate does not move properly then it may mean there is something wrong with the tracks. In case it is a minor damage then with the help of a hammer you can pound them back in shape. However, if it is a major damage then you may have to get them replaced. Most homeowners, in US cities, prefer to hire a garage door repair Skokie IL technician to do the repair work of the tracks in case of any serious damage.

* Springs: If you are checking your garage gate, then ensure to check the springs also. This is important especially if you have a roll up garage. Most of the times these springs need to be readjusted. However, it is important to know that it is always better to let an expert who deals in garage door service do the repair work of the springs, since these are dangerous if dealt with by a person who knows nothing about the technicalities.

Article Source: http://EzineArticles.com/5772944

[lets-talk-philkas-blog]

Simple Tips To Do Basic - Garage Door Repair Lakewood CO

For all those with a car or other vehicle, garage door repair is a common problem. If you own a car, you may want to make sure your garage is in good working condition. Moreover, you may not want to call a professional in case your garage door needs minor repairs. Below are a few tips that can help you carry out minor repairs.

Metal tracks

Check the door openers to make sure they are not loose. But if they are, you should go ahead and tighten all the loose screws and bolts. However, if the metal tracks are too damaged, you may want to replace them.

Alignment of the openers

The door openers have to be properly aligned. Make sure both of the tracks are at the equal height on the walls of the garage. For fixing the misaligned tracks, you should loosen the door bolts and then move the tracks into the right position with great care. Once you are done, don't forget to tighten each bolt once again.

Remove the dirt

Make sure you clear any dist or dirt from the tracks. In the same way, the tracks should be free of any hardened grease. Check the rollers and clean them properly.

Lubricate the rollers and tracks

Rollers and tracks work properly only if they are lubricated on a regular basis. For this purpose, you can go for a lubricant spray.

Tight the loose hardware

The screws of the door should be tight at all times. Aside from this, you may want to replace the damaged hinges. On the other hand, the hinges can be serviced if they sag.

Springs

The springs should be hooked in their hole. If you find it hard to do the garage door repair, all you need to do is adjust the tension in the doors. To do this, you should remove the hook of the spring to the next notch or hole.

If your garage door has a spring cable, you can adjust the tension. All you have to do is pull the cable more through the sturdy plate on the door. Once done, you can reverse the action.

Stay safe

If your garage door looks terribly damaged, don't make the mistake of fixing it on your own. Why shouldn't you do this type of repair on your own? The reason is that badly damaged garage doors are dangerous. You may end up hurting yourself or damage the door further. So, if you are sure that the door needs a major repair, you may want to contact a professional as soon as you can rather than do the repair yourself.

The takeaways

So, these are a few simple tips you can follow if you want to fix your garage door on your own. As said earlier, minor issues with the door don't require the assistance of garage door repair Lakewood CO professional, but major repairs always need an expert. In other words, contact an expert if your garage door is almost damaged or you can't do the repairs on your own.

Article Source: http://EzineArticles.com/9330819

[lets-talk-philkas-blog]

How To Install a Garage Door Repair

If you bought a brand new garage door, you may be wondering how you can save money on its installation and setup. If you are a handyman and have a few hours (or days) in front of you, you may want to attempt installing the garage door on your own. So how can you do so without damaging the door and paying for repairs before it is even installed? This article outlines the main steps to setting up a garage door on your own.

Gather the Required Tools

You may need tools such as a screwdriver, power drill, nails, screws, bolts and brackets to successfully install your garage doors. Make sure that the tools are close to you, and you should preferably use the pieces already provided by the manufacturer.

Remove the Old Garage Door

If this step hasn't already been done, you will have to undo the old door before you can install the new one. Start by unbolting the pulley system as well as unscrewing the hardware (springs, rollers etc.) You can then undo the track system and take off the door panels. Remove panel by panel to avoid having them fall on you. Make sure that children and/or pets are away from the garage during the process, as parts may fall down to the floor.

Set Up the Panels

Once you have installed the door and possibly prepared the first panel by attaching it to the doorway, you can start setting the metal tracks on the walls. You can then install the brackets and rollers on the first panel. Ask a friend or family member to help lift the second panel to install the rollers on the left and right side of the doorway and use a power drill to screw the hinges onto the panel. Repeat the process for the last panel.

Finish Installing the Tracks

Connect the jamb brackets to the tracks and then attach them securely to the framing pieces. Make sure to not screw these components in too tight because if the door isn't level, you may have to start the process all over again. You can then screw the track hanger to the wall to finish installing the horizontal tracks. It will need to be cut to the needed length to support the track.

Finishing Touches

A torque tube may be provided by the garage's door manufacturer. If you have one in your possession, install it. These are helpful to manually open and close the door. Lastly, pull the door high enough that you can verify one more time that the tracks are well placed and that the panels are leveled. You can then tightly screw the brackets to secure the whole structure.

Installing a garage door does not have to be tricky. If you understand the process pretty well, you may be able to do it by yourself. However, always have a technician's number on hand, in case you need help. Don't wait until you break your new door to call a professional, but rather do it if you have any doubts about your garage door's installation. Not doing so may cause injuries and unnecessary garage door repairs.

Article Source: http://EzineArticles.com/8492868

[lets-talk-philkas-blog]

Keep Your Home Safe With Professional Garage Door Repair Garden Grove

A garage is more than just a place to keep your car safe and to store some tools and other supplies. In most homes, the garage is another vital entry point into the house and therefore must remain secured at all time. This is why problems with the garage door should never be left till later. Also, if the problem is severe, it should be taken care of by a professional.

When their garage doors jam or break, some people simply make temporary repairs like boarding up the broken areas. They think that as long as their doors look normal, no thief would ever think about testing their garages. However, this is where they're wrong as most thieves consider garages as good places to break into. A weakened door or unsecured hinges can turn your garage into a haven for intruders.

How Can You Secure Garage Doors?

 Problems with the doors to your garage don't just pop up suddenly; usually, they have warning signs that tell you something is wrong. If your doors close slowly all of a sudden, or make loud noises, then something is up. It pays to look over the doors every now and then to make sure all the parts are in top shape. If the noises are caused by particles or rusty hinges, then a little maintenance care is in order. However, if the source of the noise is a mystery to you, professional repair services should be called. It's better to repair any problems as they happen, or else you'll end up with a huge inconvenience in your hands that will cost a lot to repair.

 Partner up with a garage door repair service that has wide availability hours. If you can, get one with 24 hour service. Your doors can give way at any time and you're in for a load of trouble if you suddenly have a garage door that won't close at 1 am. While emergency repair services are more expensive, it's a small price to pay in exchange for your security and safety.

 Consider upgrading your garage doors as a whole. If you find yourself calling your repair service provider, it might mean that your door parts have reached the end of their lifespan. Instead of burying yourself in frequent repair bills, consider a complete overhaul of your garage. It's an investment worth making because there's nothing more important than your peace of mind. With everything in top shape, you won't have to worry about it breaking in the most inconvenient of times.

To find a company that offers garage door repair Garden Grove around the clock, all you need is to search for providers through the internet or yellow pages. It pays to inquire about 24-hour services or complete garage overhauls so you can keep not only your garage but your entire home safe.

Article Source: http://EzineArticles.com/7185442

[lets-talk-philkas-blog]

Emergency Garage Door Repair San Clemente

Life has a lot of inconveniences that abruptly pop up - one of them might be a faulty garage door. If this is the case, you'll need to call an emergency garage door repair company. Since garages act as a place for your cars and provide additional security for your home, it is quite essential that you have the door fixed. Garages also function as storerooms and having an open door overnight might make you a victim of theft.

Most of the time, troubles regarding a malfunctioning door are mechanical. Sometimes it could also be a jam. You'll find it hard to close or open and sometimes the remote will not operate the way it should. Whatever the reason, getting the garage door repaired needs to be done immediately. This will require you to contact an emergency garage door repair service provider. This is definitely the quickest and most effective way of solving the problem.

Since most garages are controlled by tiny parts, assessing the real problem behind it depends on the experience of the technician. A glitch in the system affects the functionality of the door, therefore, you will have to call the technician to diagnose the problem. Figuring out the cause of the malfunction could be an extremely difficult job, which is why contacting a garage repair technician is highly recommended.

While you wait, it's okay for you to check the door - but don't do anything you are unsure of. You can check the basic stuff- things you are familiar with- such as tracks and springs, rollers, checking if they work well together or if they're in good shape. If you're not certain, wait for the technician, forcing the door to open or close may cause it more harm.

Common problems that you might encounter might be the door not closing entirely. This could be due to the limit switch. It could mean that it must be adjusted or replaced. Another problem would be the door reversing before it closes completely. This could be an issue with the close force. It may also need to be adjusted.

Waiting for a technician is a wise choice because they know the ins and outs of a garage door. They also know what precautions to take when they examine the door. This will also prevent accidents on your part. So when your door fails, calling an emergency garage door repair San Clemente company is the best choice.

Article Source: http://EzineArticles.com/6808019