#RCC Connectors

[kapilasteel]

Role of Bar Dowels in RCC Construction Using TMT Saria Bars

Bar dowels may appear like a small element within the large international world of reinforced cement concrete (RCC); however, their importance runs deep—actually and structurally. These quick metal bars, positioned among joints of concrete slabs, are key to ensuring electricity and continuity in any RCC shape. They’re not just steel rods; they’re quiet enablers of sturdiness, supporting RCC factors paintings collectively as one unified block.

Why RCC Construction Demands Precision and Support

RCC construction relies on precision. Each element—cement, aggregates, and reinforcement—must sync to withstand both time and pressure. One common weak point? Expansion joints. These joints are necessary but can lead to cracking or disjointed slabs if not managed correctly. That’s where bar dowels enter the picture, acting like bridges that transfer loads smoothly across the joint while allowing for necessary movement.

Bar Dowel Placement: A Hidden Hero Beneath the Surface

Buried within the concrete, bar dowels do the quiet job of balancing forces between adjoining slabs. Without them, one slab might shift or sink under pressure, breaking the overall integrity of the structure. Bar dowels absorb stress, provide load transfer, and prevent cracks—especially critical in pavements, roads, and industrial floors.

TMT Saria Bar: The Game Changer in Modern RCC

Now, bring the TMT saria bar into the mix, and the story gets even stronger. Thermo-Mechanically Treated (TMT) bars, regarded for their high tensile electricity and ductility, are the go-to reinforcement in RCC nowadays. Their outer surface is tough, while the core stays soft and bendable—a perfect match for bar dowel requirements.

Why Bar Dowels Work Better With TMT Saria Bars

Pairing bar dowels with TMT saria bars creates a bond that’s not just strong but also smarter. While dowels handle joint load transfers, TMT saria bars ensure that the reinforcement across the slab remains resilient and corrosion-resistant. This synergy improves the overall service life of RCC structures.

Controlling Cracks: How TMT Saria Bar Adds Support

Cracking in concrete is common—but it doesn’t have to be dangerous. Bar dowels reduce the chance of differential settlement between slabs, and TMT saria bars add another layer of strength against tension and shifting. Together, they form a protective network against early-stage structural issues.

Application in High-Traffic Zones

Think of highways, airport runways, or industrial floors. These zones face repetitive, heavy loads. Bar dowels supported by TMT saria bars allow these surfaces to withstand tons of weight while staying smooth and damage-free. Less maintenance, more lifespan.

Long-Term Cost Efficiency

Sure, quality materials might cost more upfront. But investing in bar dowels along with TMT steel pays off over time. Reduced maintenance, fewer repairs, and improved safety all lead to significant cost savings over the structure’s life.

Project-Specific Customization

Not all construction is the same, and neither are bar dowels. Using high-grade TMT saria bar allows for custom dowel sizing, cutting, and bending to match project requirements. That flexibility helps meet both design needs and structural demands.

What Makes TMT Saria Bar Ideal for RCC Joint Reinforcement?

Bar dowels need strength, ductility, and resistance. TMT saria bar delivers all three. Its bonding ability with concrete makes it ideal for embedded dowel applications. The ribbed structure improves grip, while the treated core resists bending under pressure.

Choosing the Right Combination: Final Thoughts Before You Build

When evaluating materials for RCC projects, especially where joint integrity matters, consider combining bar dowels with TMT saria bars. It’s a strategic choice—not just a structural one. The long-term stability, flexibility, and durability they bring are hard to match.

Conclusion

The unsung heroes of bolstered concrete—bar dowels—play a crucial position in making RCC constructions remain longer and perform higher. And while paired with the unequaled excellence of TMT Saria bars and TMT Metallic, they turn out to be even more powerful. Whether it’s a residential slab, a business floor gadget, or an industrial pavement, the combination of bar dowels and TMT reinforcement offers the appropriate combination of pliability, power, and sturdiness. For creation specialists trying to build smarter and more secure, the course forward is apparent: select accurately, build boldly.

[axiselectricals]

Components of an LV AB Cables Distribution Line

Low Voltage Aerial Bundled Cables, which have an insulating layer of XLPE, are an innovative concept for the distribution of electricity to households, street lights or other low voltage applications. These electrical distribution systems are practical not only in congested cities where the insulation provides safety and manoeuvrability but are also useful in rural areas where live line maintenance is much easier than using bare conductors. You can read more about this in our article on the “Advantages of Low Voltage Aerial Bundled Cables for Overhead Power Distribution”.

According to research published in 2017, “XLPE cables are expected to last or service well beyond the 40-year design life under normal circumstances”. However, this long lifespan can be severely reduced if improper clamps and connectors are used along with the AB Cable. According to the research, the most influential factor in ageing ABC cables is the use of non-standard cable connectors, accessories and clamps because they allow water ingress which slowly damages the cable.

The appropriate components to be used along with the AB Cable system are listed below.

1. Aerial Bundled Cable (ABC)

a. Insulated Messenger System: An insulated messenger system (also called the French system) consists of 3 black, weather-resistant XLPE or PE insulated phase conductors twisted along with an insulated messenger conductor made of a high strength Aluminum alloy which serves as a dual purpose earthing and/or neutral messenger wire.

b. Self-Supporting System (Two Core or Four Core System): The self-supporting cable system consists of 2 or 4 PE or XLPE black, weather-resistant insulated conductors. The mechanical strength of all the cables is equal such that, when strained, all the cables will equally bear the load of the system.

c. Uninsulated Messenger System: An uninsulated messenger system (also called the Finnish system) consists of 1-4 black, weather-resistant PE insulated phase conductors twisted around a messenger conductor made of a high strength Aluminum alloy.

2. Poles

a. Wooden Poles

b. Cement (RCC – Reinforced Cement Concrete, PCC – Plain Cement Concrete Poles)

c. Steel Tubular Pole (Stepped pole, Swaged pole).

d. Rail Pole.

3. Suspension System:

a. Suspension Clamps for LV AB Cables are used along with a bracket or other supporting hardware to suspend and grip, without damaging, the insulated or uninsulated messenger or the self-supporting system of a LV ABC system by means of an adjustable lock that accommodates a range of cable sizes.

4. Anchoring System:

a. Anchoring Clamps for LV AB Cables are used along with a bracket or other supporting hardware and are used to strain the insulated or uninsulated neutral messenger or the self-supported system to terminate into transformer leads or mains for industrial/residential supply. They are also used to provide angles to a LV ABC system without damaging the cable’s insulation.

5. Taking service lines or tap connections:

a. Service Clamps are used along with a bracket or other supporting hardware and is used to strain the insulated service conductor of an LV-ABC system without damaging the cable’s insulation. The main application of Service Clamps is to bring service connections to households or street lights.

b. Insulation Piercing Connectors are used on all AB cable systems (messenger wire as well as self-supporting system) to take tap connections. This tap can be used to continue the line, distribute the line, be used in street lighting or in-service connections to households.

6. Service line distribution

a. Distribution Boxes are used to take multiple connections from a single enclosure. These connections can be used for distribution to households.

7. Other Hardware

a. Midspan Joints are used for insulated ABC cables on stranded phase and neutral to join two cables.

b. Insulated BM Lugs are used for insulated ABC cables on stranded phase and neutral to terminate the cables.

c. Elastomeric or Heat Shrinkable End Caps are used to safely terminate the ends of the AB Cable. Elastomeric End Caps are usually supplied with insulation piercing connectors.

d. Fixing Nails are used to support Aerial bundled cable on façades.

e. Stainless Steel straps are used along with the Fixing Nails to accommodate an additional bundle if required. Stainless Steel Cable ties are also used to fix brackets and distribution boxes onto the electric pole.

f. Tensioner is used to tension the steel straps which are mounted on the poles to hold the brackets or distribution boxes in place.

To learn more about AB Cable Accessories, please watch our videos on how to install the components.

To see our range of Accessories for Aerial Bundled Cables, please visit our website. You can also find our other products, including Lightning Protection Systems, Earthing/Grounding Systems, Brass Cable Glands, Cable Lugs and more on our website.

Please email us at sales@axis-india.com or marketing@axis-india.com if you have any enquiries.

Thank you for reading the blog, Axis is a leading manufacturer and supplier of Electrical Components to over 80+ Countries.  Talk to our industry expert by visiting our contact us section. You can also watch our videos by our experts – click here.

Follow us on LinkedIn for regular updates on our Products!

[wanteddistributors]

Wanted Distributors for Pipe Connectors, Flexible Pipe, RCC Pipe, Round Pipe, Threaded Pipe In India. Get more details Please call us:+91-11-46710406

[formworksnova]

Formwork in Construction - Types and Applications of Shuttering

Shuttering or formwork is the temporary support as the moulds for the fresh concrete. In this process, the concrete gets poured. This way, they get the desired structure and gain the required strength after getting hardened. Formwork gets used in a range of sizes and shapes.

For RCC and PCC works, they get used in hydropower dams, buildings, bridges, tunnel lining, sanitary pipelines, and more. Various shuttering types get used in the 21st-century construction universe. This post shall elucidate the types and applications of formwork in construction briefly.

Timber Formwork

Easy-to-produce yet time-consuming for demanding scenarios, timber formwork satisfies a multitude of requirements. Firstly, it’s extremely lightweight. Second, it’s easily workable. Third, it’s well-seasoned. And finally, it’s absolutely free from any termite attacks.

Plywood forms

Being an artificially designed wooden material, plywood forms are available in multiple sizes and thicknesses. It’s strong, lightweight, and durable. As plywood is a popular material used for sheathing, using it is of paramount importance.

Steel Formwork

Steel framework has been becoming a popular one these days. It’s undoubtedly a bit more costly than others but it gets used for a wider range of projects. It gives smooth finishes to the concrete surface and is suitable for curved or circular structures.

Aluminium Formwork

Although it’s similar to many aspects of steel formwork, it’s lighter in weight. When the construction includes a range of repeating uses, this type becomes an effective one. Its only downfall is that there’s no alternation possible once this formwork gets constructed.

Plastic Formwork

Being an interlocking and modular system, plastic formwork gets used over 100 times. It usually serves the purpose of simpler concrete structures. Its type has been becoming popular these days, thanks to the similar shapes & larger housing schemes.

Fabric Formwork

The fabric formwork is the emerging technology in the shuttering industry for the construction of complex member or irregular shapes. The material’s flexibility makes it even more effective for producing concrete of whatsoever shapes.

Coffor Formwork

If there’s a stay-in-place formwork, it has to be this one. It gets composed of around two filtering grids reinforced by the vertical stiffeners & connected by some articulated connectors.

On the basis of structural members, there are multiple types of formwork. They are wall formwork, beam formwork, foundation formwork, and column formwork. Thus, these are the types and applications that you require understanding about construction formwork. At Nova Formworks, we use defined consulting methods and analyse formwork requirements. We understand your construction requirements and work accordingly.

[321arka]

Isolated alias single footing is utilized to provide support to single RCC columns. It is cost-effective and suitable when the columns are placed at comparatively long distances, loads operating on footings are less and the safe bearing strength of the soil usually remains high.

Isolated footing is categorized as pad footing and sloped footing.

The isolated footing is arranged underneath the column to disperse the loads securely to the bed soil.

The design of isolated footing is made for the following purposes :-

Area of footing Thickness of footing

Reinforcement details of footing with a satisfactory moment and shear force review.

The design of isolated footing is made on the basis of the guidelines set by ACI 318-14.

1. The compressive strength of concrete should satisfy the needs for both strength and stability. As per ACI 318-14, least concrete compressive strength should be 17MPa for normal applications.

2. With adherence to ACI 314-14 section 20.2.1.1, the deformed type steel bars should be used.

3. Factored forces and moments provided at the base of columns are transmitted to the foundation with reinforcement, dowels, anchor bolts, or mechanical connectors.

4. There should be least reinforcement even if the concrete bearing strength is not crossed.

5. Adequate anchorage should be arranged for tension reinforcement if reinforcement stress is not directly relative to the moment like in sloped, stepped or tapered foundation.

6. There should be sufficient anchorage length of both flexural and dowel reinforcement to get rid of bond failure of the dowels in the footing and to resist failure of the lap splices among the dowels and the column bars.

7. As per ACI 318-14 section 13.3, depth of footing over reinforcement should not remain under 150 mm.

8. The depth of the footing should be in such a manner that the shear strength of the concrete remains equivalent or surpasses the critical shear forces (one-way shear and punching shear) developed with factored loads.

9. In sloped, stepped, or tapered foundation, location and depth steps and angle of slope should satisfy design requirements at each section.

10. Concrete cover of 75 mm is necessary when the concrete is cast against soil.

11. With adherence to ACI Code specifications, base area of footing is set from unfactored forces and moments transferred by footing to soil and the permissible soil pressure evaluated through principles of soil mechanics. To get the necessary base area of the footing, the column service loads are divided with permissible net soil pressure of the soil. The net factored soil pressure is equivalent to factored load column loads by the selected footing area.

Read more

[shangshi115]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[ledsdownlight]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[ledlightstubes]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[12vledlamps]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[highpowerleds]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[householdledbulb]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[shangshi116]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[par38ledbulb]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[wanteddistributors]

Get the distributorship & dealership of Pipe Connectors, Flexible Pipe, RCC Pipe, Round Pipe, Threaded Pipe, Under the one of famous B2B brand GetDistributors. Get more details Please Contact us:+91-11-46710406

[shangshi114]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !

[colorledlightsupply]

Methods to Install Led Strips Four kinds of installation

There is 3M double faced adhesive tape in the back of some rgb led strips, and it is easy for installation, because it can be fixed on the wall by double faced adhesive tape. And every 3 led lights can be cut off to put into use alone. 2.Outdoor installation: the strips in the outdoor may be damaged by storms, so it is fixed by waterproof glue and slot. 3.Power connection: in general, the voltage of led strips is 12v, so switching power supply is needed, and its size is decided by the power and length of led strips. 4.Controller connector: 5050 smd strip and RGB led strips should be controlled by controller to achieve the transition effects. However, every controller can control different distance, so if the connecting distance is long, while controller can control it, then power amplifier is needed to tap. 5.Pay attention to the connecting distance of led: in general, if the connecting distance is beyond led strips?distance, led strip will easily produce heat which will affect its working life.  Eight reasons to explain led failure  1.Imperfection of led package damages the bulb during the transportation. 2.There is weak jointing in led strip, the vibration of transportation makes soldered dot fall down, and prevents the strips working. 3.Solder in small quantity makes soldered dot fall down. 4.Poor-quality soldering makes led strips easy to fall down and crack. 5.The installation angle is too big to separate soldered dot and copper foil. 6.Over extrusion of products during installation damage led strip chip. 7.Solder mask of circuit board is too thick, which prevents the mix of circuit board and soldering tin. 8.Led strips cannot be distorted in the process of installation.  Two kinds of driving led power supply Led strips have to work with driving power supply, led in different environments need different driving power supply. And it can be divided into two kinds. 1.According to the type of driving ,it can be divided into constant-current type and voltage regulator 2.According to the structure of circuit, it can be divided into electronic transformer, dropping resistor, conventional transformer, and RCC switch power supply. We should take care of the led strip in order to make them work more efficiently and better. At the same time, led industry will have a brighter future.  

Methods to Install Led Strips Four kinds of installation  1.Indoor installation: it is easy to install led strips which are used in indoor decoration, because it does not damaged by storm and wind. 

via Change The Length Of Your battery powered leds - china wholesale led lights https://ift.tt/2PY8Kql Methods to Install Led Strips Four kinds of installation,i hope you like it !