airconditioningservicecontr-blog

[airconditioningservicecontr-blog]

Air Conditioning Parts and Service my Area in Vancouver

Air Conditioning Parts and Service my Area in Vancouver

What're your opinions on Furnace Installation Near Me?

HOW TO LOCATE YOUR FURNACE

DO YOU KNOW HOW TO LOCATE YOUR FURNACE?

Air circulation in your home

If you have central heating, the furnace (also known as an air handler) in your home will heat your air in the winter while the blower motor circulates the air throughout your home. The AC evaporator coils for your air handler remove heat and humidity in summer. After your furnace heats or cools your air, it is then supplied to the duct system and the air begins flowing through your registers.

How many air systems run in your home?

Your thermostat is what sets the temperature in your home for your comfort. The number of thermostat(s) determine how many systems work to regulate your indoor air for heating and cooling.

Improve IAQ with Duct cleaning

Air duct cleaning can help reduce allergies from dust and other pollutants. Pollen, dust, and mold spores can get trapped in your duct work, which means that it's being continuously circulated throughout the air you breathe at home.

According to the U.S. Department of Energy (DOE), 25 to 40 percent of the energy used for heating or cooling a home is wasted. Contaminants in the heating and cooling system cause it to work harder and shorten the life of your system. Although filters are used, the heating and cooling system still gets dirty through normal use.

The National Air Duct Cleaners Association (NADCA) recommends air duct cleaning for improvement of Indoor Air Quality (IAQ). A certified duct cleaning will include cleaning of the furnace, the main trunk line [for air circulation] and all vents (including supplies and returns) each cleaned out individually.

Where is a furnace/air-handler typically located in a home?

Typically your furnace is centrally located in the home. It is usually located in an area such as a utility closet (by a cold air return), garage, attic, basement, or crawlspace; in the case of a heat-pump (a dual-system) it will be located outside of the home. When your system is run with a heat pump, it is likely a typical duct cleaning will include cleaning of evaporator coils with full system cleanings. Your furnace is usually located by other mechanical equipment such as the hot water heater, a [permanently installed] central vacuum cleaner, or a water softener, if this equipment is installed in your home.

https://www.advantaclean.com/blog/2014/november/how-to-locate-your-furnace/

Pioneer Plumbing has built a reputation of honesty with our long time returning customers. We’ve found that “doing the right thing” in all aspects of our company has brought us to where we are today, and will continue to guide us into the future. Don’t hesitate to call and ask us any plumbing, heating, ventilation, or gas related questions. Chances are if you have a tricky issue, we can solve it.

We have a few goals for our clients. One is to be available for you. It is very uncommon that when you call us we are unable to make it within the same day. We give our repeat customers priority service so if you’ve used us before and you have an emergency, we are going to do what we need to, to get someone there.

Two is to be upfront and honest. From our quotes to our service techs on site, we don’t like to beat around the bush. We will let you know our concerns, our recommendations, and our opinions on how we would handle each situation as if it were our own residence where the problem occurred. We won’t tell you the job is only a 2 hour repair when we have had situations where it turned into an all day repair.

Three is to stand behind our installations and repairs. With mechanical work, it is very common for jobs to get larger or go sideways as you get into them. If we give you a quote we will stand true to the price, if we complete a job for you and you are unhappy with the finished product, we will come back and make it right. In return, all we ask is that you communicate with our office respectfully and honestly so that we can make sure at the end of the day you are happy with our services!

So next time you have a plumbing, heating, cooling, or gas question, repair, or installation you would like quoted, give us a call! Were here to help.

HVAC in Vancouver

  Heating Repair And Seasonal Upkeep Tips

There are a few ways to maintain your furnace system. Odds are, during winter months your heater runs throughout the day attempting to keep the home warm. furnace systems generally run more than needed, because of erroneous controls. There there are various areas in your heating section to take a look at when troubleshooting for performance.

Replace The Air Filter

This is what you typically hear people talking about most often, but so few people take the recommendation and do anything about it. If there is a blockage, you either run the chance of not circulating heat properly or perhaps igniting a fire.When the air conditioner filter gets dirty air will not flow through as well which means the furnace must work overtime and will also mean a risk of fire. When a furnace works too much, it costs more to run. The fire issue is obviously self-explanatory. In both cases it is not good for peace of mind or your funds.

Test The Blower

Look at your blower blades and clean them. A dirty fan will work overtime to blow air around and naturally use higher energy to preserve the thermostat level you choose it at. Therefore the system is overworking and costing extra money to run.

Check To See That The Fire Damper Works

Next, focus on the fire damper to ensure it is running correctly. This will ensure that the risk of fire is lowered and that the system works more proficiently.

Look For Holes In The Flex Duct

Air ducts get bumped into over time. If a duct has flattened or become stopped up, the system will think that the proper temperature has been achieved, which will be false. When this happens the furnace works harder to do its job but is going to be incapable to reach the desired temperature range.

Band Insulation

Insulation is usually overlooked but is among the most regular reasons why an furnace system malfunctions. Take take time to focus on the insulation in between the duct work and the exterior to make sure it has not worked itself loose. If this happens, your equipment will not reach optimal temperatures and work overtime to attempt to accommodate.

Ductwork Needs To Be Connected

See that the ductwork has not become detached from the next section. Disconnected ductwork will allow hot air leak out and of course add to the running costs.

Return Air Inlets And The Zone Dampers

Be sure that that return air intakes are free of the dust and dirt so air can easily flow. Examine the zone dampers to see if they are in the right spot. Throughout the year we could change the position of the damper for a lot of reasons (i.e. getting into a tight space or making room for storage). For a properly working system, check to see that the dampers are actually in the best place.

If this is a tad too much to handle yourself, we propose you hire an area plumbing contractor certified for furnace and heating repair. There will be numerous heating specialists close to you who can care for all of this quite competently. For the right results you could set up annual up-keep for furnace and your heating people will call yearly to deal with it.

https://www.google.com/maps?cid=16109373416364653742 https://vancouver-plumber.business.site/

https://www.pioneerplumbing.com/

Pioneer Plumbing & Heating Inc

626 Kingsway, Vancouver BC, V5T 3K4 Phone: (604) 872-4946

Business Hours: Sunday Open 24 hours Monday Open 24 hours Tuesday Open 24 hours Wednesday Open 24 hours Thursday Open 24 hours Friday Open 24 hours Saturday Open 24 hours

  As a keen reader on Gas Furnace Installation Cost, I imagined sharing that topic was really useful. I beg you take the opportunity to distribute this blog posting if you enjoyed reading it. Thanks a lot for your time invested reading it.

Furnace Repair Water Heater Repair Heating Replacement Electric Furnace Installation Central Heating Installation

Air Conditioning Parts and Service my Area in Vancouver

[airconditioningservicecontr-blog]

Air Conditioning Service Contractor For Hire in Vancouver

Air Conditioning Service Contractor For Hire in Vancouver

We have found this post about HVAC Repair directly below on the internet and believe it made good sense to share it with you over here.

What’s the cheapest way to heat your home this winter?

We all want to keep our homes nice and warm in winter, without spending a fortune. To find out the best way to save on heating, we did some research into the pros, cons and costs of electricity, gas and wood.

Find out which is the most cost effective and efficient way to heat your home this winter.

Electricity

Startup costs

You can buy a cheap fan heater, which is very efficient for warming a room quickly, for under R200. A 9-fin oil heater costs around R800. The better quality the heater, the more you will pay.

Cost of electricity

The heat energy of a heating device is measured in kilowatts (kW). The current cost of electricity in Johannesburg is R1.24 per kW. A 9-fin oil heater or an elctric fan uses around 2kW in an hour, so at R1.24 per kW, it will cost you R2.48 per hour.

Remember, though, that during peak times (between 07:00 and 10:00 and 17:00 and 21:00 on weekdays) in certain municipalities in winter, electricity can be billed at 2.5 times the standard rate. This Time of Use Tariff means that you’ll be paying R6.20 to use a heater during these times.

Heat generated

In South Africa, our heaters are limited by the type of power they can draw from our plug points, so the maximum heat they can generate is 3kW. However, as most of our heaters are imported, the maximum they can generate is 2kW, in line with European limitations.

Pros

Electric heaters are available in a range of sizes, functionality, cost and heat efficiency. In addition, the costs of heating a room with electricity are not overly high. And it’s convenient - as long as the power’s on, it is always available at the flip of a switch.

Cons

Electric heaters are dependent on the Eskom power supply, which means that if there is no power, you will have no heat. Certain types of heater – oil heaters, for instance – take a long time to warm up. Other types – like bar heaters – give a more immediate radiant heat, but there is a risk of burning yourself or even starting a fire. Electric heaters do tend to dry out the air but a humidifier or bowl of water nearby will solve that.

Gas

Startup costs

A portable gas heater starts in the region of R800 to R1 000. A 9kg gas bottle requires a deposit of R300 and the gas itself costs R200 for each refill.

Cost of gas

It is calculated that a 9kg gas canister, which costs around R200, will be used up in around 30 hours – so that’s R6.67 an hour.

Heat generated

Mobile gas heaters can give out over 4kW of heat. You can manually adjust their temperature to give out less heat, and thus use less gas.

Pros

Gas heaters deliver instant heat and are therefore very efficient at warming a room – or your cold hands!

Cons

The costs of gas and gas heaters are comparatively quite high. Also, gas heaters consume oxygen and so the room must be well ventilated. And you will have to arrange for gas to be delivered to your home, or take your gas bottles to be refilled.

Wood-burning stove

Start-up cost

David Wantling, a heating expert and the managing member of J Macdonald and Sons (trading as macD Fire House), says that a wood-burning stove or a closed combustion fireplace costs between R10 000 and R25 000, with installation of around R5 000.

Note that the following calculations do not include open fireplaces, which are very inefficient; only around 15% to 20% of the heat radiates into the room while the rest goes up the chimney.

Cost of wood

The cost of fuel for a wood-burning stove is far less than the cost of using electricity or gas. A bag of hard, well-seasoned wood containing around 25 pieces costs around R45. David estimates that a fire loaded with six pieces will burn for more than six hours at a moderate level. This means that the stove will consume about one piece of wood per hour at a cost of R1.80 per hour for an output of 6 to 8kW of heat. The cost is therefore around 30c per kW.

Heat generated

Closed wood-burning stove have an efficiency of up to 80%. Wood stoves’ heat outputs are generally rated as: small – 3kW to 6kW, medium – 5kW to 9kW, and large – 8kW to 12kW, and very large - above 12kW. The size of the space would determine the size fireplace you need.

Pros

Wood-burning stoves give off a lot of warmth very efficiently, and wood is an inexpensive fuel to burn in this way.

Cons

The start-up costs of buying and installing a wood-burning stove are fairly steep. And you will have to make arrangements to purchase wood.

The conclusion

Wood-burning stoves, while the most expensive to purchase, burn wood at a slow rate while generating a lot of heat, and are the most-cost effective way to heat a room.

Electric heaters are the cheapest to purchase, and their running costs are the second cheapest after wood stoves.

Mobile gas heaters are generally more expensive than their electric counterparts and their fuel is more costly than electricity and wood.

Of course, most people make the decision to heat their homes based on the equipment that they already have available and the convenience of getting hold of the right type of fuel. However, with the rising costs of all types of fuel, it is worth considering the financial implications of any heating solution that you opt for, so be sure that you go into any purchase or installation with your eyes open – especially with the wide range of products and models on the market.

https://www.1life.co.za/blog/heat-home

Pioneer Plumbing has built a reputation of honesty with our long time returning customers. We’ve found that “doing the right thing” in all aspects of our company has brought us to where we are today, and will continue to guide us into the future. Don’t hesitate to call and ask us any plumbing, heating, ventilation, or gas related questions. Chances are if you have a tricky issue, we can solve it.

We have a few goals for our clients. One is to be available for you. It is very uncommon that when you call us we are unable to make it within the same day. We give our repeat customers priority service so if you’ve used us before and you have an emergency, we are going to do what we need to, to get someone there.

Two is to be upfront and honest. From our quotes to our service techs on site, we don’t like to beat around the bush. We will let you know our concerns, our recommendations, and our opinions on how we would handle each situation as if it were our own residence where the problem occurred. We won’t tell you the job is only a 2 hour repair when we have had situations where it turned into an all day repair.

Three is to stand behind our installations and repairs. With mechanical work, it is very common for jobs to get larger or go sideways as you get into them. If we give you a quote we will stand true to the price, if we complete a job for you and you are unhappy with the finished product, we will come back and make it right. In return, all we ask is that you communicate with our office respectfully and honestly so that we can make sure at the end of the day you are happy with our services!

So next time you have a plumbing, heating, cooling, or gas question, repair, or installation you would like quoted, give us a call! Were here to help.

HVAC in Vancouver

  Why Heating Repair is Bound To Happen When Up Keep Is Ignored

There are many ways to maintain your furnace system. Chances are good the system shall be running full-time in the winter. In fact, it is usually on more than it must be because it is unable to maintain an efficient atmosphere. When trouble shooting and optimizing your heating segment of your furnace system, there are various areas to look at.

The Air Filter

This part is what gets mentioned the most in chats about heating maintenance, but is sometimes neglected. If there is a obstruction, you either run the risk of not disbursing heat properly or perhaps starting a fire.When the air filter gets dirty air cannot flow through either which suggests the furnace must work harder and could also mean a likelihood of fire. If the system is not circulating heat effectively, it is working harder. You want eliminate any exposure to fire. Neither scenario is good for your wallet or your well-being..

Assess The Blower

Have a look at the blower blades to ensure they are free of crap. A messy fan will work harder to blow the air around and of course use higher energy to preserve the temperature level you choose it at. Therefore strain on your furnace system and your budget since more fuel is needed to continually run the blower.

Check To See That The Fire Damper Works

Next, look at the fire damper to ensure it is running the right way. This will ensure that the risk of fire is reduced and that the system works more efficiently.

The Flex Duct

Air ducts can get damaged over the years. If a duct has collapsed or become blocked, the system will believe that the right temperature has been achieved, which will be false. Finally your system will be working harder to maintain your house cool while you continue lowering the thermostat to reach comfortable settings.

Make Sure The Insulation Is Secure

Insulation is often forgotten but is one of the most common reasons why an furnace system does not work properly. Be sure to check the insulation and confirm it has never become loose and resulted in gaps involving the ductwork and the exterior. If this has happened, your system will not reach optimum temperatures and work overtime to attempt to accommodate.

Air Ducts Need To Be Sealed

Make sure the ductwork is hooked up everywhere to all pieces. These detachments can cause space in the air flow and result in a loss of hot air in your home, since it will be escaping through the gaps.

Return Air Inlets And The Zone Dampers

Be sure that that return air intakes are free of dust and debris so air can easily flow. Check your dampers verifying that they are in the right spot. Through the year we may change the positioning of the damper for many reasons (i.e. getting into a tight space or arranging for storage). For a properly working system, check to see that your dampers are in the best spot.

If that is a little too much to handle yourself, we suggest you hire an area plumbing contractor certified for furnace and heating repair. You will find a number of heating companies around you who can take care of all of this quite competently. For the right results you can set up annual upkeep for furnace and the heating people will call yearly to take care of it.

https://www.google.com/maps?cid=16109373416364653742 https://vancouver-plumber.business.site/

https://www.pioneerplumbing.com/

Pioneer Plumbing & Heating Inc

626 Kingsway, Vancouver BC, V5T 3K4 Phone: (604) 872-4946

Business Hours: Sunday Open 24 hours Monday Open 24 hours Tuesday Open 24 hours Wednesday Open 24 hours Thursday Open 24 hours Friday Open 24 hours Saturday Open 24 hours

  I stumbled upon that blog entry about Home Furnace Installation when doing a lookup on the internet. Loved our content? Please quickly share it. Help someone else find it. Thanks so much for your time invested reading it.

Furnace Repair New Furnace Installation Furnace Repair Service Heating System Replacement AC HVAC Repair

Air Conditioning Service Contractor For Hire in Vancouver