mlikang

[mlikang]

Is your water flosser leaking? Don’t worry, here are some solutions!

Are you having water leaks when using your water flosser? Don’t worry, here are some simple ways to help you solve it!

Check the water tank: First, make sure the water tank is installed correctly. Sometimes, it’s just a problem caused by improper installation.

2. Check the seal: Check that the seal between the waterpik and the main body of the water flosser is intact and not worn or damaged.

3. Clean the filter: A clogged filter can also cause water leaks. Clean the filter regularly to ensure smooth water flow.

4. Check the valve: Some water flossers have a pressure regulating valve, which can also cause water leaks if it is damaged or clogged.

5. Contact after-sales service: If none of the above methods can solve the problem, it is recommended that you contact the after-sales service center of the water flosser factory for professional help.

For a small water leak, you might as well try these methods to get your water flosser back to normal!

[mlikang]

Water does not come out of the water flosser? Don't worry! 5 common reasons and solutions

If your water flosser does not come out, you can refer to the following step-by-step solutions, which summarize common fault causes and corresponding measures:

Quick self-repair steps (applicable to sudden water failure)

Check basic settings‌ Confirm that the water tank has sufficient water and is installed in place to avoid air intake due to lack of water or unsealed water tank.

Try to remove the nozzle and turn it on to observe whether water comes out of the host interface to determine whether the nozzle is blocked.

Unblock the pipe and nozzle‌

Physical unblocking‌: Unplug the nozzle and clean the foreign matter at the nozzle with a toothpick or a fine needle; flush the interface with the faucet for 30 seconds to flush away the internal impurities.

Negative pressure ventilation method‌: Use your mouth to gently suck the nozzle (similar to sucking air with a straw) to use air pressure to unblock the blocked pipe. (Pay attention to cleaning the nozzle) Water backwash‌: Without installing the nozzle, start the water flosser and aim the interface at the running tap water for 10-15 seconds to expel air or impurities.

Dealing with scale blockage ‌ → Add ‌white vinegar and water (1:1 mixture)‌ to the water tank, let it stand for 1 hour, then turn on the machine to flush the pipes and dissolve the scale. → For stubborn scale, repeat the operation or extend the soaking time.

Targeted troubleshooting

The motor runs but no water comes out ‌ Pipe deformation/adhesion ‌: Common when it is idle for a long time. Remove the water pipe to check whether it is flattened, and manually pinch it to reset it; apply a small amount of lubricating oil when reinstalling it to reduce friction.

Filter blockage ‌: Replace the filter from the oral irrigator manufacture (matching model required).

Abnormal water pipe connection ‌: Check whether the water pipe interface is loose, twisted, or aging and broken, and re-insert or replace the accessories.

No response or abnormal sound ‌ Power supply problem ‌: Check whether the charging port is oxidized and whether the power adapter is damaged.

Tip: If the motherboard is burned due to the wrong insertion of high-voltage power supply, professional repair or replacement of power module is required.

Prevention and daily maintenance Regular descaling ‌ Clean the water tank and pipes with white vinegar solution once a month to prevent scale accumulation. Storage and maintenance ‌ Empty the water tank after use and store it dry; avoid heavy objects pressing on the body and causing deformation of the pipe. Activation after long-term idle ‌ When using for the first time, fill the nozzle interface with water before installation, or run it at no load for 10 seconds to exhaust the air. Notes Be careful when disassembling and repairing! Non-professionals are advised to refer to brand tutorials (such as Philips HX8460 removable shell to adjust the water pipe) or contact after-sales. If the above method does not work, it may be a motor failure or motherboard damage, and it needs to be sent to a professional repair point for inspection.

Tips for different brands oral irrigator: Philips ‌: Gently suck the nozzle to exhaust when the box is empty; or shake the body for 30 seconds after filling with water. Xiaomi/Libode ‌: Focus on checking whether the water outlet plug is blocked, and the pipe needs to be thoroughly cleaned. Waterpik ‌: After sucking through the nozzle, add white vinegar to clean to prevent recurrence.

Most blockage problems can be solved with simple operations, and regular maintenance is the key!