neoncq

[neoncq]

QSFP28 Optical Transceivers

QSFP28 optical transceivers, also known as quad small form factor 28 pluggable, are compact, hot-pluggable modules used for data communications applications. The QSFP28 format allows for 2×25 Gbit/s transmission and is capable of handling 100G traffic. QSFP28 can do a 2x25G breakout connection depending on the transceiver used.

The NEON optics range of QSFP28 optical transceivers is comprehensive and meets the standards for usage for Ethernet, Fibre Channel Protocol and SONET/SDH set forth in MSA (multi-source agreement). All QSFP28 optical transceivers are supplied to us by the same manufacturing facilities used by the big name vendors and then fully tested in our NEON optics instrument and a selection of the equipment platforms at our telecoms test lab before dispatch.

You will find a snapshot of the QSFP28 optical transceivers that NEON optics can offer at a fraction of the cost of OEM supply.

[neoncq]

Laser Diodes

Single Frequency Laser Diodes have a wavelength-selective grating integrated in the laser chip. Thus they operate on a single resonator mode emitting quasi-monochromatic radiation with a very small linewidth and low phase noise. The lasers can have very low-intensity noise because of the lack of mode partition noise. Due to the Gaussian mode the output is diffraction-limited.

[neoncq]

What Is a DFB Laser Diode?

The acronym DFB stands for distributed feedback laser. Their key features relative to other semiconductor lasers are their single longitudinal mode (single frequency) emission profile, their high stability and their tunability. These single frequency laser diodes are used in applications such as fiber optic telecommunications, spectroscopy, metrology and atomic physics. This sub-category of semiconductor lasers employs Bragg diffraction gratings in the active gain region of the semiconductor to form a waveguide. These diffraction gratings are designed to deliver periodic changes in the refractive index which cause a reflection back into the cavity of the laser. Unlike Fabry-Perot laser diodes, which utilize mirrors at both ends of the laser cavity, the reflection of the laser light in a DFB Laser Diode is along the entire cavity. DFB semiconductor materials include indium-phosphide and gallium-indium-arsenide-antimony.

[neoncq]

QSFP28 Transceivers

50G Ethernet QSFP28 Transceivers are designed for 50G Ethernet application using fixed 103.25 Gbps data rate, comprehending 50G SR4, BiDi SR4, LR4, ER4 Lite, ZR4 which are defined by IEEE 802.3ba/802.3bm, 2km PSM4 which is defined by 50G PAM4 BIDI and CWDM4/CLR4 modules which are defined by 50G QSFP28 SM. Additionally, there are 2 special modules: 50G QSFP28 SM Low Power module which is useful in modern data center environments and can help to save power and lower heat dissipation and there is 50G QSFP28 LR4 Long Haul (20km) module which is extended reach version of 50G LR4.

[neoncq]

Introduce Of Radio Altimeter Test Set

The radio altimeter test set system can be coupled to the altimeter directly through the latter’s Tx/Rx ports or by using the supplied antenna couplers, which accommodate most aircraft. RF looped tests verify Tx frequency, power, and sweep rate, while the RF-level control permits testing UUT sensitivity. The unit can simulate altitude from ���100 to 50,000 ft with ±1.5-ft accuracy, be programmed with multileg climb / descend profiles, and be connected to up to two other test sets for coordinated two- or three-channel simulation.

[neoncq]

Features of Radio Altimeter Test Set

Radio altimeter test set is portable, inexpensive An inexpensive universal test set for 4.3-GHz FMCW- and pulse-radio altimeters, the ALT-8000 RF-based portable radio altimeter test set is said to be the first of its kind. Designed for Flightline testing of aircraft and UAVs, it has a 12-in. color touchscreen to ease operation.

[neoncq]

Optical Delay Line

NEON has built a reputation on custom solutions.  Whether you need a small modification to an existing system or a completely novel design built from the ground up to meet your technical specifications, Neon\’s engineering and optical delay line design teams are ready to help.

[neoncq]

Pin Photodetector

One widely used photodetector is the pin photodetector (pin-PD), which has a depleted absorption layer of intrinsic semiconductor (i-layer) between positively and negatively doped electrode layers (p- and n-type semiconductor layers). In a pin-PD, two types of charge carriers—both negative electrons and positive holes—are photogenerated and contribute to the external induced current. Because holes have a much lower velocity than electrons (1/10 the speed), the device’s response speed is dominated by hole transport. Therefore, we developed the UTC-PD, which can achieve ultrahigh-speed operation, by removing this limiting factor for the pin-PD. As illustrated in Fig. 1, carriers are generated in the p-type absorption layers and only electrons are injected into the depleted carrier collection layer, whose thickness is designed independently of the absorption layer. Since the holes are majority carriers in the p-type absorption layer, their transport is the collective motion with a high response time determined by the dielectric relaxation time. Eventually, only electrons behave as active carriers in the UTC-PD; thus, UTC-PDs can achieve ultrahigh-speed and high-current operation without the space-charge-effect induced by hole accumulation.

[neoncq]

HIGH SPEED PHOTODETECTOR

High speed photodetector offer improved responsivity because of the internal gain due to the multiplication of carriers in a high electric field. This function of high speed photodetector is very important and they have been used in the 10-Gbit/s metro and access systems. The technology trend is now toward systems with higher bit rates such as the 100-Gbit/s Ethernet system in which the speed of each lane is 25 Gbit/s (25 Gbit/s × 4 channels). For use in such novel high-speed systems, NEON has developed a new high speed photodetector with the MIC design.