#Setup D-Link DCS-930L

[dlinkrouterlocalblog]

How to Setup D-Link DCS-930L

Zero Configuration Setup:- As well as the Zero Configuration Setup will only work with a registered Cloud Router and an active mydlink account. Hence your Cloud Router will automatically assign your camera’s network settings (both wired and wireless), and add the camera to your mydlink account. This means you'll find out your camera by simply plugging it in and connecting it to your router.

Connect the Power Cable and Ethernet Cable:-

Step 1:- The facility supply to the facility receptor located on the rear of the DCS-930L and connect it to a wall outlet or power strip. Power is confirmed when the facility LED is lit.

Step 2:- If using an Ethernet connection, connect the included Ethernet cable to the Ethernet port located on the back of your camera. Plug the opposite end into an available port on your D-link Cloud Router.

Note: As well as you later decide to use your camera wirelessly, you will be able to remove the cable after Zero Configuration Setup is complete.

Add Your Camera to Your mydlink Account:-

Step 3:- From a computer connected to the Internet, open a web browser (e.g., Internet Explorer, Chrome, Firefox, or Safari) and go to http://www.mydlink.com. Sign in to your mydlink account.

Step 4:- As well as the mydlink page will automatically check for new devices. Hence once mydlink detects your camera, a notice will appear that says , Zero Configuration (at rock bottom of the screen). Click the notification to continue.

Step 5:- As well as confirmation request will appear with a summary of the configuration details. Make a note of the small print and click on Yes to feature the camera to your account. Your setup is complete! Note:- If you experience issues registering this device together with your mydlink account, perform a tough reset by pressing and holding the push button on the device for 10 seconds while the device is powered on.

Step 6:- Hence you will see the mydlink Live View for your camera. As well as the screen will look similar to the screenshot on the right. 

Note:- You used an Ethernet connection and now want to connect your camera to your router wirelessly, you can simply disconnect the Ethernet cable and move the camera to the preferred location. As well as the router’s wireless settings were automatically transferred to the camera during Zero Configuration Setup, so no further configuration is required.

D-Link DCS-930L Manual Installation:-

Hence if you prefer to set up your camera without using the Camera Setup Wizard, follow the steps below.

Connect the Power Cable and Ethernet Cable

Step 1:- The facility supply to the facility receptor located on the rear of the DCS-930L and connect it to a wall outlet or power strip. Power is confirmed when the facility LED is lit.

Step 2:- If using an Ethernet connection, connect the included Ethernet cable to the Ethernet port on the back of the camera. Plug the opposite end into an available port on your router

WPS - Push Button Setup and installation Create a WPS Connection:-

Step 1:- As well as with the camera powered on, press and hold the WPS button for about three seconds. Hence the blue WPS status LED above the button will blink.

Step 2:- As well as press the WPS button on your router within 60 seconds. The WPS button is probably on the back of your router. Hence if you are not sure where the WPS button is located on your router, refer to your router’s User Manual. On some routers, you'll have to log in to the online interface and click on an on-screen button to activate the WPS feature.

Step 3:- Allow up to at least one minute to configure. As well as the DCS-930L will automatically create a wireless connection to your router. Hence while connecting, the green LED will flash and your camera will reboot. WPS Button If your router supports Wi-Fi Protected Setup (WPS), the easiest way to create a secure wireless connection is by using the WPS Button on the back of the camera. In general, WPS setup only establishes the connection, so you continue to run the Setup Wizard to configure your camera. As well as the exception is Zero Configuration setup with a D-Link Cloud Router. You can use WPS to attach the DCS-930L to your router, then register your camera with mydlink.

[amigoccs]

Setup a Surveillance System to Proof Crash of Asus RT-AC1200G+

If Asus ask you to provide video proof for RMA issue on crash point, it's easy with NAS.

I write this post is related to ASUS ORDER CUSTOMERS TO PROVIDE VIDEO PROOF ON A CRASH ISSUE THEY HAVE REPRODUCE THAT HAPPENS ON THEM on 1st RMA: From 2017/5/15 till Now section in Asus RT-AC1200G+ Random Reboots Automatically.

Here I use DCS-930L Wireless N Network Camera from D-Link and AS-5102T from Asustor as an example to setup surveillance system and keep track of the light on Asus…