#sims4gun

[viktorviolettaenterprises]

🇩🇪 German Maschinenpistole 5/ MP5 🇩🇪

Special Thanks To @mimoto-sims For Claire’s Outfit... Such A Magnificent Work :)

@ts4-poses @ts4-poses-masterlist

DOWNLOAD!!!!!

One of the masterpiece in the machine pistol's realm. It's known by it's simplicity, accuracy and relative reasonable price. Designed in H&K as a SMG variant of G3 Rifle and rolled out in 1966. Until today, it's still in the armory of 70 countries around the world, not including the militias which utilises this babies. And now we're gladly bring it tio The Sims 4 format

Variants:

1.Standard Model

H&K MP5A4 & MP5A5 The MP5A4 (fixed stock) and MP5A5 (sliding stock) models, which were introduced in 1974, are available with four-position trigger groups. The pistol grips are straight, lacking the contoured grip and thumb groove of the MP5A1, MP5A2, and MP5A3. The selector lever stops are marked with bullet pictograms rather than letters or numbers (each symbol represents the number of bullets that will be fired when the trigger is pulled and held rearward with a full magazine inserted in the weapon) and are fully ambidextrous (the selector lever is present on each side of the trigger housing). The additional setting of the fire selector, one place before the fully automatic setting, enables a two or three-shot burst firing mode.  the A5 Model Got 2 Stage Of Stock (Retracted and Extended) For Extreme Realism

H&K MP5/10 In 1992, Heckler & Koch introduced the MP5/10 (chambered in 10mm Auto) .which are based on the MP5A4 and MP5A5. These weapons were assembled in fixed and retractable stock configurations (without a separate designation) and are fed from translucent 30-round polymer box magazines. These weapons include a bolt hold-open device, which captures the bolt group in its rear position after expending the last cartridge from the magazine. The bolt is then released by pressing a lever positioned on the left side of the receiver. Both weapons use a barrel with 6 right-hand grooves and a 380 mm (1:15 in) twist rate, and like the MP5-N, both have a 3-lugged muzzle device and a tritium-illuminated front sight aiming dot.

2.Sub Compact Model

H&K MP5K

In 1976, a shortened submachine gun version of the MP5A2 was introduced; the MP5K (K from the German word Kurz = "short") was designed for close quarters battle use by clandestine operations and special services. The MP5K does not have a shoulder stock (the receiver end was covered with a flat end cap, featuring a buffer on the inside and a sling loop on the outside), and the bolt and receiver were shortened at the rear. The resultant lighter bolt led to a higher rate of fire than the standard MP5. The barrel, cocking handle and its cover were shortened and a vertical foregrip was used to replace the standard handguard. The barrel ends at the base of the front sight, which prevents the use of any sort of muzzle device. In 1991, a further variant of the MP5K was developed, designated the MP5K-PDW (PDW—Personal Defense Weapon) that retained the compact dimensions of the MP5K but restored the fire handling characteristics of the full-size MP5A2. The MP5K-PDW uses a side-folding synthetic shoulder stock (made by the U.S. company Choate Machine and Tool), a "Navy" trigger group, a front sight post with a built-in tritium insert and a slightly lengthened threaded, three-lug barrel (analogous to the MP5-N). The stock can be removed and replaced with a receiver endplate; a rotary drum with apertures from the MP5A2 can also be used.

3.Sub Sonic Model

H&K MP5SD5 & H&K MP5SD6

In 1974, H&K initiated design work on a sound-suppressed variant of the MP5, designated the MP5SD (SD—Schalldämpfer, German for "sound suppressor"), which features an integral but detachable aluminium sound suppressor and a lightweight bolt. The weapon's 146 mm (5.7 in) barrel has 30 2.5 mm (0.1 in) ports drilled forward of the chamber through which escaping gases are diverted to the surrounding sealed tubular casing that is screwed onto threading on the barrel's external surface just prior to the ported segment. The suppressor itself is divided into two stages; the initial segment surrounding the ported barrel serves as an expansion chamber for the propellant gases, reducing gas pressure to slow down the acceleration of the projectile. The second, decompression stage occupies the remaining length of the suppressor tube and contains a stamped metal helix separator with several compartments which increase the gas volume and decrease its temperature, deflecting the gases as they exit the muzzle, so muffling the exit report. The bullet leaves the muzzle at subsonic velocity, so it does not generate a sonic shock wave in flight. As a result of reducing the barrel's length and venting propellant gases into the suppressor, the bullet's muzzle velocity was lowered anywhere from 16% to 26% (depending on the ammunition used) while maintaining the weapon's automation and reliability. The weapon was designed to be used with standard supersonic ammunition with the suppressor on at all times. The MP5SD is produced exclusively by H&K in several versions: the MP5SD1 and MP5SD4 (both have a receiver end cap instead of a buttstock), MP5SD2 and MP5SD5 (equipped with a fixed synthetic buttstock) and the MP5SD3 and MP5SD6 (fitted with a collapsible metal stock). The MP5SD1, MP5SD2 and MP5SD3 use a standard 'SEF' trigger group (from the MP5A2 and MP5A3), while the MP5SD4, MP5SD5, and MP5SD6 use the 'Navy' trigger group—a trigger module with a mechanically limited 3-round burst mode and ambidextrous selector controls (from the MP5A4 and MP5A5). A suppressed version was produced for the U.S. Navy—designated the MP5SD-N, which is a version of the MP5SD3 with a retractable metal stock, front sight post with tritium-illuminated dot and a stainless steel suppressor. This model has a modified cocking handle support to account for the slightly larger outside diameter of the suppressor. The design of the suppressor allows the weapon to be fired with water inside, should water enter the device during operation in or near water.

[viktorviolettaenterprises]

🇬🇧 1776 Ferguson Breechloader Rifle 🇬🇧 Another Request to one of Our Patron.. I’d like to share to all of you, Enjoy

The Ferguson rifle was one of the first breech-loading rifles to be put into service by the British military. It fired a standard British carbine ball of .615" calibre and was used by the British Army in the American Revolutionary War at the Battle of Brandywine in 1777, and possibly at the Siege of Charleston in 1780.  Its superior firepower was unappreciated at the time because it was too expensive and took longer to produce – the four gunsmiths making Ferguson's Ordnance Rifle could not make 100 in 6 months at four times the cost per arm of a musket.

Special Thanks To @revolution-sims For Such Beautiful British Redcoat Uniform, Keep up a good work, Sister

DOWNLOAD

[exzentra]

Hey! Today I want to share 8 Poses including 4 weapons with you. I have converted these objects by @sg5150 to accessoires for your sims. Credit for the weapons goes to the original creators (TS3): Capitol Sims / XanKriegor / Dead Rising

Thank´s to all Cc Creators :*

Weapons: Download (MediaFire)

Poses: Download (MediaFire)

-don´t re-upload!!