#Rockspace WiFi Extender Setup

[wifi-range-extender-setup]

Rockspace WiFi Extender Setup 

A Rockspace WiFi extender Setup can significantly enhance your wireless network coverage, ensuring a strong and stable connection throughout your home or office. Setting up your Rockspace WiFi extender is a straightforward process. Step by step guide on how to set up a Rockspace WiFi extender:

Setting up Rockspace WiFi Extender:Manual Method

Step-by-step guide Rockspace WiFi extender setup manually. This guide assumes a generic setup process; the specific steps might vary slightly based on the model you have. Follow these steps to manually set up your Rockspace WiFi extender:

Plug in the extender near your router and wait for the power LED to become solid.

 Connect your device (computer or smartphone) to the WiFi network named "Rockspace-XXXX" (where XXXX represents the last 4 digits of your extender's MAC address).

Open a web browser and enter "ap.setup" or “192.168.10.1" in the address bar.

To finish the setup, follow the on-screen steps, which include selecting your existing WiFi network and entering its password.

Once the extender connects to your router's network, you can relocate it to an optimal location.

Following these steps should help you manually set up your Rockspace WiFi extender. Remember, it's important to consult your extender's specific user manual for accurate and detailed instructions to your model.

Rockspace Extender Setup using WPS method

Rockspace WiFi extender Setup using the WPS (Wi-Fi Protected Setup) method can be a quick and convenient way to extend your WiFi coverage:

Plug in the extender and wait for the power LED to become solid.

Press the WPS button on the extender.

Within 2 minutes, press the WPS button on your router.

Once the extender's WiFi LED becomes solid, the setup is complete.

Note: The WPS setup process might vary slightly depending on the model of your Rockspace extender. Please refer to the user manual that came with your extender for precise instructions.

How do I perform a factory reset on a Rockspace WiFi extender?

To perform a factory reset on a Rockspace WiFi extender, follow these steps:

Locate the reset button on the extender (usually on the side or back).

Use a paperclip or pin to press and hold the reset button for about 10 seconds.

When the LEDs begin to flash, release the button.

The extender will reset to its default settings.

By performing a factory reset, you'll essentially start over with a clean slate, allowing you to set up the extender as if it were brand new. Always refer to your specific extender's manual for the most accurate and detailed instructions on performing a factory reset.

Update Rockspace WiFi Extender Firmware 

Updating the firmware of your Rockspace WiFi extender is important to ensure that it's running the latest software version, which can improve performance, security, and functionality. Step by step general guide on how to update the firmware:

Visit the Rockspace official website and navigate to the support section.

Enter your extender's model number to find the latest firmware version.

Save the firmware file to your computer after downloading it.

Log in to the extender's web interface (using the IP address from the manual setup step).

Look for the "Firmware Update" section and upload the downloaded file.

Wait for the update to complete and do not interrupt the process.

Note:That the exact steps may vary depending on the specific model of your Rockspace WiFi extender. Always refer to the user manual or documentation provided by Rockspace for accurate and model-specific instructions.

Troubleshooting Steps:

If you're experiencing issues with your Rockspace WiFi extender Setup, there are several troubleshooting steps you can take to identify and resolve the problems.Here is a list of basic troubleshooting steps.

Ensure the extender is within a reasonable distance from the router.

Check that the extender's power LED is solid and not blinking.

Verify that you are connecting to the correct extended WiFi network.

Restart both the extender and your router.

Make sure the WiFi password is correctly entered during setup.

Update the firmware on the extender to the most recent version.

Perform a factory reset and set up the extender again from scratch.

By following these setup and troubleshooting guidelines, you can maximize the performance of your Rockspace WiFi extender and enjoy seamless connectivity across your space. If persistent issues occur, referring to the product's user manual or contacting Rockspace's customer support can provide further assistance.

[sadiesiink75]

Connect Rock Space WiFi Extender to New Router

[digitaltechside]

How to Configure a Rockspace WiFi Extender?

The Rockspace WiFi extender setup  is a straightforward process. Begin by plugging the extender into a power outlet within the range of your existing WiFi network. Once powered on, connect your computer or mobile device to the Rockspace_ext network using the default password provided in the user manual. Follow the on-screen instructions to log in (use the default username and password from the manual), select your existing WiFi network, and enter its password. Complete the setup process by following any additional prompts. Once configured, the Rockspace extender will amplify your WiFi signal, providing extended coverage for a more robust wireless connection.

Read More:-

[wirelessextender]

Get your Rockspace wifi range extender up and running in no time. Follow our easy step-by-step guide for setting up your extender and expanding your wireless network range. Enjoy the improved coverage and faster internet speeds today!

[httprerockspacelocal]

How To Connect Rockspace Wifi Extender Setup?

Rockspace wifi extenders are the most convenient and quick solution to increase the range of your existing Wifi.

To connect your rockspace wifi range exetnder to your phone or laptop, follow these steps:

Before connecting, switch off your mobile network.

Then, connect the WIFI extender to an electrical outlet.

Wait until the indication remains solid on.

Open WIFI on your Android, iPhone, or PC now.

To connect, select ROCKSPACE WIFI EXTENDER.

After a successful connection, open the web page and enter re.rockspace.local to configure the WIFI extender's password.

Locate the existing WIFI network that you want to expand, and then type on the existing WIFI network.

Finally, it has been linked.

You can now relocate it to a location where the networks are poor (dead zone area) or where you want to expand your network.

Default Login for Rockspace Wifi Range Extender

Before proceeding with the extender device configuration, you must have the login credentials for your ROCKSPACE booster device in order to conveniently access settings and control it swiftly. In addition, the default Login IP address, username, and password are printed on the ROCKSPACE Sticker, and a simple user manual is supplied with the box.

The default login URL is re.rockspace.local, and the IP address is 192.168.10.1**.**

Default username: NA

ROCKSPACE password- For the first time you log in, you must create a new password.

When you have everything ready to set up a range extender device, it is time to move on to the next stages.

Open your WEB BROWSER and navigate to re.rockspace.local or 192.16810.1, then wait for the login screen to load. During the initial configuration of the range extender, you must now generate a new login password. So enter a strong login password and then click the next button.

Final Words

These were the steps to assist you set up and log in to the Rockspace wifi Extender dashboard. If you are having trouble logging in, you may contact our customer service, we will assist you with your problem.

Visit: https://re-rockpacelocal.com/rock-space-wifi-extender-setup/

[routerloginsetupnet]

Use your IP address to log in to the internet:

It's linked to a clandestine network. The SSID name of the switch is shown on the device's bottom and can be altered in simultaneous settings.

Open your program on your device and type 192.168.0.1 into the address box, then press Start on the first page.

Select a connection type. The switch has three connection methods: PPPoE, Dynamic IP Address, and Static IP Address.

You'll find autoconfiguration here. You can choose the precise type of link in your network by giving data as needed. The next button should be pressed.

Keep in mind that if you're using a PPPoE connection, you'll need to provide your PPPoE client name and password before pressing Next.

[profoundlandcreator]

Rockspace Extender General Guide

Rockspace Extender General Guide

Network dead zones are always a headache for those using a wireless connection. The best solution for this problem is to use a Wireless Extender. It's harder to pick a good Extender from the whole lineup with the value for money as well. One of the best manufacturers who create the best Wireless Extender is Rockspace. Each consumer can pick Extender from a huge lineup in various price sectors. Re rock space local wifi extender boost your signals and make your workplace no dead zone area.

Rockspace local wifi extender works at single 2.4 GHz and the most famous model from Rockspace Extender is AC1200 which supports dual-band too. These Wireless Extenders are very easy to setup device. Rockspace Extender can set up with the single press via WPS and also setup via online through their official setup page http://re.rockspace.local. or 192.168.0.254. We can go through a detailed step by step process in the following sections

Features On Rockspace Extender

* High Signal boost.

* Full signal coverage

* Easy setup via WPS and Web UI

* Almost compatible with all devices.

* Smart signal indicator helps to find the perfect spot easily.

* Most models support dual-band which is future proof.

* Some models support Access Point Mode.

Things inside the Box

 * Rockspace Wireless Extender

* Power cable and adaptor

* Quick Guide / Manual

* Warranty Card

Important Extender Models from Rockspace

Rockspace Extenders comprises of various single-band and dual-band Extenders in 2.4GHz and 5GHz. Most important model from Rockspace is AC-1200 Dual Band Repeater. AC750 is another model within a more budget section. Different models come with different features as well. All models include single press WPS setup but your router should also support WPS connection. Rockspace AC-1200 also works in triple mode; it can work as an Access point as well. The important part of Extenders is to proper positioning of Wireless Extenders. The position must be midpoint from the router as well as a dead zone to get maximum coverage and maximum performance. Some models come with a smart signal indicator as well. This shows the signal level graphically which is easier to find the perfect spot.

Rockspace Extender Setup

As we mentioned before, there are two ways to set up your Rockspace Extender. You can set up with the single press via WPS and you can set up in online through re.rockspace.local. or 192.168.0.254.

We can briefly go through each setup in the following steps.  

Rockspace Extender Setup with Web UI

To set up your Extender via Web UI, you need a web browser installed. We prefer Google Chrome and Mozilla Firefox. There is a specific website as well to do this setup, Connect to http://re.rockspace.local or 192.168.0.254. from the connected device.

 1. Power your Rock space Extender.

2. Connect your device Wi-Fi device to rockspace_EXT WiFi network.

3. Open any above-mentioned web browser from the connected device.

4. Open the above-mentioned link from the device via a web browser.

6. Select the WiFi Network.

7. Enter your Wi-Fi Password from the connected device.

8. Reposition your Wireless Extender to any better spot.

9. Start Enjoying your Extended Network connection.

 Rockspace Extender Setup with WPS

 Rockspace Extender also comprises of another easy method. In this method, the only requirement is the ability of your router for WPS. For all those devices which don't support WPS can use the above method. We can go through this method steps now.

 1. Power your Extender through an AC outlet.

2. After turning ON, Press WPS button on your router.

Note: If there's no WPS button, go for the above method.

3. Now press WPS button on your Rockspace Wireless Extender

4. Reposition your Rockspace Extender which prescribed in the description.

5. Connect your device as your comfort.

6. Start Enjoying your Network connection.

 Rock space Extender setup as Access Point

 Rockspace Extender can be used as an Access Point instead of working as an Extender. We can go through step by step process for Access Point setup now. re.rockspace.local login is needed in the official Website.

 1. Power your Rockspace repeater via Electrical outlet.

2. Connect your Rock space Extender to your Router using any compatible Ethernet cable.

3. Now follow the steps as mentioned above.

4. Open any web browser and open Rockspace Extender Webpage via websites mentioned in the Web browser.

5. In the website, change the connection mode as Access Point and start using your Rockspace Extender as Access Point.

FAQ

There are lots of doubts regarding Rockspace Extender. We can go through some questions now.

 1. Important Question is my rock space wifi extender not working.

A. If you go through the above steps correctly, there will be no problem. If there is no power in your Extender, then you can demand a replace or repair from the manufacturer.

 2. After Extending, do we need new SSID and password?

A. No, you can use the same SSID and password of your Wi-Fi router.

 3. Which connections Rockspace Extenders work?

A. Almost all models work in WPA, WPA2.

 4. What do the colours from the device represent?

A. Blue colour indicates a good connection, Red colour indicates poor connection and no colour indicate No connection at all.

 5. Rock space Extender support dual-band or single band?

A. Rock space Extender supports the single band in some models and dual-band in some other models. Most famous AC 1200 supports dual-band.

 6. Is there a mobile application for rockspace Extender?

A. No, but there is a website for remote managing the Extender and set up process as well.

  As a whole, Rock space Extenders is the best option for anyone looking for a good Wireless Extenders in any price point. It comes with good enough features and also budget-friendly as well. Rock space works hard to make you worth every penny External antennas help to give the best coverage available in the market. Even though there is no stand-alone mobile application for Rockspace, Website is good enough to forget that negative. The Best Wireless Extender or the best value for money Wireless Extender from Rockspace is definitely the Rockspace Wireless dual-band Extender AC-1200.

Read more…   https://re-rockspace-local.com/

[techtrickszonedotcom]

Rock Space AC750 and Ac1200 Range Extender Setup

[lilacharlie]

Re.rockspace.local

The private web address re.rockspace.local is responsible to let you interact with your WiFi extender. If you have a Rockspace range extender, you can get access to it through this private web address. The URL can help you configure or manage your extender’s wifi network without any cables or wires. 

All you have to do is, connect to the extender and go to the re.rockspace.local web page. The web-based interface does not even ask for an active internet connection in order to get inside your device. Want to learn how to login to the Rockspace range extender through this address, follow the steps below:

Firstly, ensure that your extender is plugged into the power outlet. 

Go to a web browser on a device connected to the extender. 

Type http://re.rockspace.local in the browser and hit Enter. 

Put down the username and password upon reaching the re rockspace local login page. 

Make sure you enter the login credentials carefully. 

Click Login. You will log into the Rockspace wifi extender successfully. 

That was all about the Rockspace WiFi extender and how to login to it using the private web address. 

[rudraglambeauty]

There are some astonishing steps mentioned for re.rockspace.local setup. Let’s obtain more meticulous erudition about it from here.

[smartwifiplus]

Only the offline method at re.rockspace.local / http://re.rockspace.local can be used to configure the rockspace ac2100 extender setup

[rerockpace-blog]

Re.Rockspace.local wifi extender setup

For bigger zones where remote transmission is required, re.rockspace nearby wifi extender goes about as a repeater to support the sign and keeps it from deadzone region. Fundamentally, re.rockspace neighborhood wifi extender works at 2.4G band in this manner giving full sign inclusion transmission speed of 300 Mbps. Additionally, AC1200 wifi run extender is accessible that works at double band and lift your home system by expanding the range and speed of wifi signal. To arrangement the association with switch, one needs to simply press the WPS button and inside couple of moments the association with expand the sign will be set up. Thus, a reset button is given on the gadget by which the wifi extender can be reestablished to default settings. The reset button must be squeezed until the pointer turns red.

Steps to Follow Re.Rockspace local wifi extender Configuration

To arrange and interfacing the re.rockspace.local wifi extender to a gadget, one must follow the rockspace wifi extender arrangement guidelines gave on http/re.rockspace.local. For broadening the wifi signal by wifi extender, we can utilize WPS fasten or can likewise login to Web UI (utilizing an advanced mobile phone) and check the sign quality. In addition for better wifi inclusion and sign quality, the reception apparatuses must be situated appropriately. When you login effectively to web UI, you can check the status of associated switch or gadgets and wifi name. On this page, we can likewise alter the settings of wifi extender and can arrangement new login name and secret key. To spare and initiate any of the changed settings, we need to reboot the extender. In any case, on the off chance that we reset the extender, at that point it will be set to the default settings and one needs to arrangement all the settings again in the extender.

At times, the gadget may perform strange tasks, at that point one needs to visit the rockspace wifi extender site http://re.rockspace.local or 192.168.0.254 and utilize the refreshed programming to determine the specific issue.

Read more…..  https://re-rockspace-local.com/

[wirelessextender]

Are you struggling with the Rockspace WiFi extender setup? If the answer is yes and you are confused about how to setup rockspace wifi extender then don’t panic! Here, you will get the best setup guide for the Rockspace range extender setup. 

[gracillymarte8962]

Rock Space gives a portable application to both Android and iPhones that permits you to deal with your organization and makes the arrangement interaction unbelievably simple. Directly from the application you can likewise make visitor organizations should you need to give restricted admittance or an alternate arrangement of qualifications to your visitors. Also, the course of action from the site re.rockspace.local can be successfully done on your wifi engaged device after you partner your wifi go extender properly. When the Rockspace extender a game plan you can move it to another zone where the wifi signals are satisfactory so the extender will spread the framework similarly to all the zones of the house.

[profoundlandcreator]

How to Setup Rockspace Extender

Rock space extenders are well known in the market when it comes to best affordable extenders without compromising with the quality of wifi Connection. If you are on this page because you wanted to Setup Rockspace Extender then just follow the below given instructions. First of all make sure that your Rockspace Extender is plugged in to the wall near your router then only start the Re.Rockspace.Local Setup process. Before we start Setup its important to make sure extender have solid light on power.

Read more about Re rock space Extender....