applefixnz-blog - Tumblr blog

[applefixnz-blog]

iphone water damage repair Hamilton new Zealand

Badly water damaged iphone shorted pp-vdd-boost and pp-lcm-bl-anode this video also explain how to find short using thermal camera and freeze spray

iphone repair specialist in hamilton new zealand.

call 078394111 or visit 125 ward street hamilton New Zealand

mail in Repair read info here https://applefix.co.nz/send-your-device/

logicboard and microsoldering repair courses in New zealand read info here https://applefix.co.nz/logicboard-repair-course/

lcd refurbish course read info here https://applefix.co.nz/lcd-refurbish-course/

[applefixnz-blog]

Nintendo Switch Light NOT Charging Charging port replacement nintendo Switch Repair Hamilton nz

Nintendo switch repair experts in hamilton New zealand Call 078394111 or visit 125 ward street hamilton www.applefix.co.nz

Mail in device read instructions here https://applefix.co.nz/send-your-device/

logicboard repair courses https://applefix.co.nz/logicboard-repair-course/

lcd refurbish courses https://applefix.co.nz/lcd-refurbish-course/

How to replace Nintendo switch charging port? read general guide below

Replacing the charging port on a Nintendo Switch can be a bit intricate and requires some technical skill. Here's a general guide on how you might go about it:

Tools Required:

Tri-wing screwdriver

Phillips head screwdriver

Tweezers

Plastic pry tool

Replacement USB-C charging port

Heat gun

Soldering Iron

Steps:

Prepare Your Workspace:

Find a clean, well-lit area to work in.

Lay down a soft cloth to prevent scratches to the screen or back of the Switch.

Power Down the Switch:

Ensure the Nintendo Switch is completely powered off before beginning any repairs.

Remove the Back Panel:

Use the tri-wing screwdriver to remove the screws from the back panel.

Gently pry off the back panel using a plastic pry tool. Be careful not to damage the plastic clips holding it in place.

Disconnect the Battery:

Inside, you'll find the battery connector. Use a plastic pry tool to disconnect it. This is important for safety reasons.

Locate and Remove the Charging Port:

The charging port is typically located at the bottom of the Switch.

Remove any screws securing the charging port in place.

Carefully disconnect any ribbons or cables attached to the charging port.

Replace the Charging Port:

Take your new USB-C charging port and connect any ribbons or cables to it.

Secure the charging port in place with the screws you removed earlier.

Reconnect the Battery:

Carefully reconnect the battery connector.

Replace the Back Panel:

Snap the back panel back into place, ensuring all clips are secured.

Replace the screws using the tri-wing screwdriver.

Test the Switch:

Before fully reassembling the Switch, it's wise to test if the new charging port is working properly.

Plug in the charger and ensure the Switch recognizes it and begins charging.

Reassemble the Switch:

Once you're sure the charging port is working, you can replace any remaining screws and fully reassemble the Switch.

Tips:

Be Patient: Take your time and don't rush the process. Rushing can lead to mistakes or damage to the device.

Keep Track of Screws: Use a magnetic mat or tray to keep track of screws and small parts during disassembly.

Watch Tutorials: If possible, watch video tutorials or read detailed guides specific to Nintendo Switch charging port replacements for visual guidance.

If you're uncomfortable performing this repair yourself, it might be best to seek assistance from a professional technician or repair service.

[applefixnz-blog]

laptop dc jack repair | Laptop Not Charging | laptop repairs in Hamilton new zealand 

Laptop Not turning on or not charging . How to solder DC jack on the cable. Laptop dc jack repairs in Hamilton new Zealand125 ward street hamilton New Zealand Call 078394111Soldering Process for Replacing Laptop DC Jack: Prepare the New DC Jack: Ensure that the new DC jack is compatible with your laptop model. Examine the soldering points on the new DC jack and make sure they match those on the motherboard. Prepare the Motherboard: Clean the soldering area on the motherboard using isopropyl alcohol and cotton swabs. This removes any dirt, dust, or residue that could interfere with the soldering process. Tinning the Soldering Points: Apply a small amount of solder to the soldering points on the motherboard and the corresponding terminals on the new DC jack. This process is called "tinning" and helps ensure good electrical conductivity during soldering. Positioning the New DC Jack: Carefully position the new DC jack on the motherboard, aligning it with the soldering points. Ensure it sits flush against the motherboard. Soldering: Heat up your soldering iron to the appropriate temperature for soldering electronic components. Hold the soldering iron against the soldering point on the motherboard and the corresponding terminal on the DC jack. Apply a small amount of solder to the joint. The solder should melt and flow smoothly, creating a solid connection between the two components. Repeat this process for each soldering point, ensuring that the connections are secure but not excessively soldered, which could cause shorts. Inspect the Solder Joints: After soldering all the connections, visually inspect the solder joints to ensure they are smooth, shiny, and without any bridges or cold solder joints. Use a magnifying glass if needed to check for any imperfections. Reassembly: Once you're satisfied with the soldering job, proceed with reassembling the laptop following the steps outlined in the previous guide. Testing: Before fully reassembling the laptop, perform a test to ensure the new DC jack is functioning properly. Connect the power adapter and battery and power on the laptop. Check if the laptop charges properly and if there are any issues with the power connection. Final Checks and Cleanup: Once you've confirmed that everything is working correctly, tidy up any loose wires and secure them with electrical tape or heat shrink tubing. Clean the laptop's exterior with a soft cloth and isopropyl alcohol if necessary. By following these steps carefully and using proper soldering techniques, you should be able to successfully replace the DC jack on your laptop. Remember to work slowly and carefully to avoid damaging any components. If you're not comfortable with soldering, consider seeking assistance from a professional technician. or bring it to applefix hamilton new zealand www.applefix.co.nzS

[applefixnz-blog]

ipod 6th 7th repair experts in hamilton new zealand . applefix hamilton call 078394111 or visit 125 ward street hamilton

We specialize in logic board and liquid damage repair and can fix your Laptop, MacBook, mobile phone , ipad, iphone , tablet , playstation, xbox or any other electronic gadget that has been deemed unfixable by another repair shop.

*Have a repair shop and are looking to outsource logic board repairs? We offer discounted repairs to other repair shops, schools, large organizations and government agencies. — https://applefix.co.nz/contact/

logicboard repair course in New Zealand

Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology.

This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment.  Start your own business or increase your chances to get job quickly.  https://applefix.co.nz/logicboard-repair-course/

 Mail in device info read here https://applefix.co.nz/send-your-device/

[applefixnz-blog]

Replacing the rear camera on an iPhone 13 Pro Max requires precision and care. Keep in mind that attempting to replace components on your own may void your warranty, and it's always recommended to seek professional help if you are not confident in your skills. If you're still determined to proceed, here is a general guide for informational purposes only. Please note that the specific steps may vary, and it's crucial to follow the guidelines provided by the device's manufacturer.

Disclaimer: Performing a rear camera replacement on your own may lead to further damage to your device. If your iPhone is still under warranty or AppleCare, it's advisable to contact Apple or an authorized service provider for assistance.

iPhone 13 Pro Max Rear Camera Replacement Procedure:

1. Gather Tools:

Screwdrivers (Pentalobe and Phillips)

Plastic or metal spudger

Tweezers

Suction cup

Plastic opening tools

2. Power Off the iPhone:

Turn off your iPhone before starting the repair.

3. Remove the Screws:

Use a Pentalobe screwdriver to remove the screws around the device frame.

4. Open the iPhone:

Use a plastic opening tool or a case opening tool to carefully open the iPhone. Be gentle, and avoid using excessive force.

5. Disconnect the Battery:

Once the device is open, locate and disconnect the battery to ensure safety during the repair.

6. Remove Logic Board Shield:

Remove any shields covering the logic board components using a Phillips screwdriver.

7. Disconnect Camera Module:

Locate the rear camera module and carefully disconnect it from the logic board. Be cautious not to damage any connectors.

8. Remove the Camera:

Gently remove the old camera from its housing. It may be secured with screws or adhesive.

9. Install the New Camera:

Place the new camera into the housing and secure it with screws or adhesive.

10. Reconnect Camera to Logic Board:

Connect the new camera to the logic board using the appropriate connectors.

11. Reassemble the iPhone:

Reverse the steps to reassemble the iPhone. Ensure all screws are tightened, and connectors are securely in place.

12. Power On and Test:

Power on the iPhone and test the new camera to ensure it's functioning correctly.

Note: Power on the iPhone and test the new camera to ensure it's functioning correctly. Note: This is a general guide, and the actual procedure may vary. If you are not comfortable or experienced with electronics, it's strongly recommended to seek professional at applefix hamilton 125 ward street hamilton New Zealand

[applefixnz-blog]

ipad air chrging port was replaced but still not charging, tested charging ic 1610a3 was faulty replaced and it charging fine Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology. This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment. Start your own business or increase your chances to get job quickly. read info here https://applefix.co.nz/logicboard-repair-course Mail in device read info here https://applefix.co.nz/send-your-device We specialize in logic board and liquid damage repair and can fix your Laptop, MacBook, mobile phone , ipad, iphone , tablet , playstation, xbox or any other electronic gadget that has been deemed unfixable by another repair shop. *Have a repair shop and are looking to outsource logic board repairs? We offer discounted repairs to other repair shops, schools, large organizations and government agencies. — https://applefix.co.nz/contact/ logicboard repair course in New Zealand Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology. This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment. Start your own business or increase your chances to get job

Replacing the charging IC (Integrated Circuit) on an iPad Air involves intricate soldering work and should be done with caution. If you're not experienced with microsoldering or electronics repair, it's recommended to seek professional assistance, as attempting these repairs without proper expertise can lead to further damage. Here's a general guide for informational purposes only:

Note: This information is for educational purposes, and I am not responsible for any damage that may occur during the repair process. Proceed at your own risk.

Tools and Materials Needed:

Replacement charging IC compatible with iPad Air.

Microsoldering iron with fine tips.

Hot air rework station.

Soldering flux.

Solder wick or desoldering braid.

Tweezers.

Magnifying glass or microscope for precision work.

Isopropyl alcohol and a brush.

ESD-safe workplace and wrist strap.

Procedure:

Prepare Your Workspace:

Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components.

Disconnect Power:

Power off the iPad and disconnect it from any power source.

Disassemble the iPad:

Follow a disassembly guide specific to your iPad Air model to expose the logic board.

Locate the Charging IC:

Identify the charging IC on the logic board. It is typically located near the charging port.

Apply Soldering Flux:

Apply soldering flux to the charging IC and the surrounding components. This helps in soldering and desoldering.

Desolder the Old Charging IC:

Use the hot air rework station and microsoldering iron to carefully desolder the old charging IC. Use solder wick to clean up any remaining solder.

Clean the Area:

Clean the area around the charging IC with isopropyl alcohol and a brush.

Place the New Charging IC:

Carefully place the new charging IC in the correct orientation. Ensure proper alignment.

Solder the New Charging IC:

Use the hot air rework station and microsoldering iron to solder the new charging IC onto the logic board. Be precise to avoid damage to nearby components.

Inspect Your Work:

Inspect the solder joints under a magnifying glass or microscope to ensure they are clean and free of defects.

Reassemble the iPad:

Put the iPad back together in the reverse order of disassembly.

Test the Charging Functionality:

Connect the iPad to a power source and check if it charges properly.

If you are not confident in your microsoldering skills or if the issue persists after the replacement, it's advisable to seek assistance from a professional technician or a reputable repair service. Microsoldering requires precision, and any mistakes could lead to further damage.

[applefixnz-blog]

https://applefix.co.nz/blog/ipad-air-not-charging-u2-tristar-1610a3-charging-ic-replacement-ipad-repair-hamilton-new-zealand

[applefixnz-blog]

Dead macbook pro A1708 board number 820-00875 moisture damaged | type C power managed IC u3100 CD3215B03 replacement. macbook repair experts in hamilton new zealand applfix call 078394111 visit 125 ward street hamilton new zealand Replacing the USB-C power IC (Integrated Circuit) on a MacBook A1708 involves delicate soldering work and should only be attempted by individuals with experience in electronics repair and soldering. If you're not comfortable with these skills, it's strongly recommended to seek professional assistance. Additionally, performing unauthorized repairs may void any existing warranties. Here's a general guide for informational purposes only. Note that this information is not a step-by-step guide, and specifics can vary based on the nature of the repair and the MacBook model: Tools and Materials Needed: Replacement USB-C power IC compatible with MacBook A1708. Soldering iron with a fine tip. Desoldering wick or solder sucker. Solder. Flux. Precision screwdrivers. ESD-safe workplace and wrist strap. Magnifying glass or microscope for precision work. Procedure: Prepare Your Workspace: Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components. Disconnect Power: Power off the MacBook and disconnect it from any power source. Disassemble the MacBook: Follow a disassembly guide specific to the MacBook A1708 model to expose the logic board. Locate the USB-C Power IC: Identify the USB-C power IC on the logic board. It's often located near the USB-C port. Apply Flux: Apply soldering flux to the USB-C power IC and the surrounding components. Desolder the Old IC: Use a soldering iron and desoldering wick or solder sucker to carefully remove the solder from the USB-C power IC's connections on the logic board. Remove the Old IC: Gently lift and remove the old USB-C power IC from the logic board. Be careful not to damage nearby components. Clean the Pads: Clean the solder pads on the logic board using isopropyl alcohol and a brush. Prepare the Replacement IC: Align the replacement USB-C power IC with the solder pads on the logic board and prepare to solder it in place. Solder the New IC: Use the soldering iron to solder the replacement USB-C power IC onto the logic board. Be precise and avoid creating solder bridges between connections. Inspect Your Work: Inspect the solder joints under magnification to ensure they are clean and free of defects. Reassemble the MacBook: Put the MacBook back together in the reverse order of disassembly. Test the USB-C Port: Connect the MacBook to a power source and test the USB-C port to ensure that the replacement IC is functioning correctly. If you are not confident in your soldering skills or if you encounter difficulties during the process, it's strongly recommended to seek professional help. Applefix new zeland are expert in macbook repairs in hamilton new zealand call us on 078394111 or visit 125 ward street hamilton new zealand

[applefixnz-blog]

Upgrading the SSD in an iMac involves several steps, and it may vary depending on the specific model. Here's a general guide that covers the process for some iMac models. Before proceeding, make sure to check the compatibility and warranty implications, and if you're not comfortable with the process, consider seeking professional help.

Note: This information is for educational purposes only, and I am not responsible for any damage that may occur during the upgrade process. Proceed at your own risk.

Tools and Materials Needed:

Compatible SSD: Ensure the new SSD is compatible with your iMac model.

Screwdrivers: Typically, you'll need a Phillips screwdriver.

Opening tools: Plastic or metal spudgers for safely opening the iMac.

External Drive Enclosure (optional): If you need to clone data from the existing drive.

Backup: Ensure you have a backup of your important data before starting.

Procedure:

Check Compatibility:

Verify that the SSD you have is compatible with your iMac model.

Backup Data:

Perform a backup of your important data. You can use Time Machine or any other backup method of your choice.

Power Off and Disconnect:

Power off your iMac and disconnect it from any power source.

Ground Yourself:

Use an anti-static wrist strap or regularly touch a grounded metal surface to discharge static electricity.

Open the iMac:

Follow the iMac's user manual or online guides to open the case. This often involves removing screws and using opening tools to release clips.

Locate the SSD:

Identify the existing SSD or HDD and its location within the iMac.

Remove Existing SSD:

Carefully disconnect and remove the existing SSD. It might be held in place by screws or connectors. Take note of how it's installed for reference.

Install the New SSD:

Place the new SSD in the same location and connect it securely. Make sure to follow any specific installation instructions provided with the SSD.

Close the iMac:

Carefully close the iMac and secure any screws that were removed.

Clone Data (Optional):

If you're not performing a fresh installation of the operating system, you may need to clone the data from the old drive to the new SSD. Use an external drive enclosure and cloning software for this purpose.

Boot Up and Test:

Power on your iMac and check if the new SSD is recognized. If you've cloned data, ensure that everything is working as expected.

Install macOS (If Necessary):

If you've installed a new, empty SSD, you may need to install macOS. You can do this using macOS Recovery or a bootable USB drive.

Format the New SSD (If Necessary):

If the new SSD is not recognized or needs formatting, use Disk Utility to format it correctly.

Remember to consult the specific documentation for your iMac model, as the procedure can vary. If you're uncertain or uncomfortable with any step, bring it to applefix Hamilton new Zealand 124 ward street Hamilton

[applefixnz-blog]

Repairing an HDMI port on an Xbox One X involves delicate soldering work and should be approached with caution. If you're not comfortable with electronics and soldering, it's recommended to seek professional assistance. Additionally, attempting this repair may void your warranty. Here's a general guide for informational purposes only:

Note: This information is for educational purposes, and I am not responsible for any damage that may occur during the repair process. Proceed at your own risk.

Tools and Materials Needed:

Replacement HDMI port compatible with Xbox One X.

Precision screwdriver set.

Plastic opening tools or spudgers.

Soldering iron with a fine tip.

Desoldering wick or solder sucker.

Solder.

Flux.

Heat gun or hot air rework station.

ESD-safe workplace and wrist strap.

Procedure:

Prepare Your Workspace:

Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components.

Disconnect Power:

Power off the Xbox One X and disconnect it from any power source.

Disassemble the Xbox One X:

Follow a disassembly guide specific to the Xbox One X model to expose the internal components.

Locate the HDMI Port:

Identify the HDMI port on the Xbox One X's motherboard.

Desolder the Old HDMI Port:

Use a soldering iron and desoldering wick or solder sucker to carefully remove the solder from the HDMI port's connections on the motherboard.

Remove the Old HDMI Port:

Once the solder is removed, gently lift and remove the old HDMI port from the motherboard.

Clean the Pads:

Clean the solder pads on the motherboard using isopropyl alcohol and a brush.

Apply Flux:

Apply flux to the cleaned solder pads to improve solder flow.

Solder the New HDMI Port:

Align the replacement HDMI port with the solder pads on the motherboard and solder it in place. Be precise to avoid creating solder bridges between connections.

Inspect Your Work:

Inspect the solder joints under magnification to ensure they are clean and free of defects.

Reassemble the Xbox One X:

Put the Xbox One X back together in the reverse order of disassembly.

Test the HDMI Port:

Connect the Xbox One X to a TV or monitor using an HDMI cable and test if the port is functioning properly.

If you're not confident in your soldering skills or if you encounter difficulties during the process, it's strongly recommended to seek professional help. Additionally, be aware that attempting to repair your Xbox One X on your own may void any existing warranties.

[applefixnz-blog]

Macbook Pro A1990 820-01326 Short on G3H Dead Liquid Damaged | Macbook repairs New Zealand

Macbook pro 15.6 A1990 water damaged. Board number 820-01326.

Macbook repair experts AppleFix 125 ward street Hamilton New Zealand Call 078394111

mail in repair instructions read here https://applefix.co.nz/send-your-device/

A general guide to macbook a1990 repair

Repairing a shorted G3H issue on a MacBook A1990 involves troubleshooting and locating the component or area that is causing the short. This process requires a good understanding of electronics, proper tools, and caution. If you're not comfortable with electronics repair or don't have experience with MacBook repairs, it's strongly advised to seek professional assistance, as attempting repairs without proper expertise can lead to further damage.

Here's a general guide for informational purposes only. Note that specifics can vary based on the nature of the short and the MacBook model:

Tools and Materials Needed:

Multimeter.

Schematics and boardview files for MacBook A1990.

Isopropyl alcohol and a brush.

Thermal camera (optional).

Soldering iron and soldering equipment.

ESD-safe workspace and wrist strap.

Procedure:

Prepare Your Workspace:

Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components.

Disconnect Power:

Power off your MacBook and disconnect it from any power source.

Disassemble the MacBook:

Follow a disassembly guide specific to your MacBook model to expose the logic board.

Inspect for Visible Damage:

Visually inspect the logic board for any signs of physical damage, burnt components, or liquid damage. Clean the board with isopropyl alcohol and a brush.

Check for Short Circuits:

Using a multimeter in continuity mode, check for short circuits on the main power rails, especially G3H. Compare your readings to the expected values from the schematics.

Identify Components:

Use the schematics and boardview files to identify the location of the G3H power rail and the components connected to it.

Thermal Imaging (Optional):

Use a thermal camera to identify hotspots on the logic board. Overheating components may indicate the area of the short.

Isolate Components:

Remove or lift components connected to the G3H power rail one by one and check for changes in the multimeter readings.

Inspect the Battery:

The battery could be a source of a short. Disconnect and inspect the battery, checking for any signs of damage.

Soldering Work:

If you identify a shorted component, carefully desolder it and replace it with a new one. Pay attention to proper soldering techniques.

Test After Each Step:

Power on the MacBook after each step to check if the short has been resolved.

Reassemble and Test:

Once you've identified and resolved the issue, reassemble the MacBook and perform a thorough test to ensure proper functionality.

Remember, MacBook logic board repairs, especially dealing with shorts, can be intricate and challenging. If you're not confident in your skills, it's advisable to seek the help of a professional technician or a reputable repair service. AppleFix Hamilton are experts in macbook repairs call 078394111 or visit 125 ward street hamilton new Zealand

[applefixnz-blog]

If you're experiencing issues with no sound from the ear speaker and loudspeaker on your iPhone 8 Plus, and the speaker button is grayed out, it could be due to a variety of reasons, ranging from software issues to hardware malfunctions. Here are some steps you can take to troubleshoot and potentially resolve the problem:

Before you bring it to applefix Hamilton new zealand try below steps

1. Restart Your iPhone:

Sometimes, a simple restart can resolve software glitches. Turn off your iPhone and then turn it back on.

2. Check Silent Mode and Volume Settings:

Ensure that your iPhone is not in silent mode check the silent switch on the side and that the volume is turned up.

3. Update iOS:

Make sure your iPhone is running the latest version of iOS. Software updates can include bug fixes that might address audio issues.

4. Reset All Settings:

Go to Settings  General  Reset  Reset All Settings. This won't delete your data, but it will reset system settings like Wi-Fi passwords and wallpaper. Check if the issue persists after the reset.

5. Check for Software Issues:

Sometimes, third-party apps or software glitches can cause audio problems. Try playing sound through different apps to see if the issue is app-specific.

6. Check for Water Damage:

If your iPhone has been exposed to water or moisture, it could be affecting the speakers. Check for any signs of water damage, and if present, consider drying your phone or seeking professional assistance.

7. Inspect the Audio Port:

Ensure that the audio port is not clogged with debris. Use a small, soft brush or compressed air to clean it.

8. Perform a Hard Reset:

Perform a hard reset by pressing and holding the power button and volume down button simultaneously until you see the Apple logo. This can help resolve temporary software issues.

9. Check Audio Settings:

Go to Settings  Sounds & Haptics and adjust the Ringer and Alerts volume. Make sure the Change with Buttons option is enabled.

10. Restore iPhone:

If none of the above steps work, you may need to restore your iPhone to factory settings using iTunes. Make sure to back up your data before doing this.

11. Hardware Inspection:

If the issue persists after trying all software-related solutions, there may be a hardware problem. In this case, it's advisable to contact Apple Support or visit an Apple Authorized Service Provider for further assistance.

iphone 8 plus no sound from era speaker and loud speaker and speaker button is grayed out. iphone 8 plus audio codec ic 338S00248  u4700 replacement

applefix hamilton new zeland iphone repair in new zealand call 078394111 125 ward street hamilton

mail in device read instructions here https://applefix.co.nz/send-your-device/

logic board repair courses in new zealand https://applefix.co.nz/logicboard-repair-course/

lcd refurbish course in new zealand

[applefixnz-blog]

Xbox one S digital broken hdmi port replacement. AppleFix Hamilton 125 ward street are xbox repair experts. Call 078394111

If you dont live in hamilton mail in your device read instructions here https://applefix.co.nz/send-your-device/

logicboard repair courses in new Zealand

lcd refurbish course in New Zealand

Repairing or replacing an HDMI port on an Xbox One S Digital Edition requires technical skill and should be approached with caution. If you are not comfortable with electronics and soldering, it's recommended to seek professional help or contact Microsoft for support. If you have the necessary skills, here is a general guide to replacing the HDMI port: For a professional xbox one s hdmi port repair bring it to applefix 125 ward street Hamilton New Zealand or call 078394111

Note: This information is for educational purposes only, and I am not responsible for any damage that may occur during the repair process. Proceed at your own risk.

Tools and Materials Needed:

Replacement HDMI port.

Soldering iron and solder.

Desoldering wick or solder sucker.

Precision screwdrivers.

Opening tools.

ESD-safe workplace and wrist strap.

Steps:

Prepare Your Workspace:

Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components.

Disconnect Power:

Power off and unplug your Xbox One S Digital Edition.

Disassemble the Xbox:

Follow a disassembly guide specific to your Xbox One S Digital Edition model. This usually involves removing the case and exposing the internal components.

Locate the HDMI Port:

Identify the HDMI port on the Xbox One S Digital Edition's motherboard.

Desolder the Damaged HDMI Port:

Use a soldering iron and desoldering wick or solder sucker to carefully remove the solder from the existing HDMI port's connections on the motherboard.

Remove the Old HDMI Port:

Gently lift and remove the damaged HDMI port from the motherboard.

Solder the New HDMI Port:

Align the replacement HDMI port with the solder pads on the motherboard and solder it in place. Be precise and avoid creating solder bridges between connections.

Inspect Your Work:

Examine the solder joints to ensure they are clean and free of defects. Check for any accidental solder bridges or cold solder joints.

Reassemble the Xbox:

Put the Xbox back together in the reverse order of disassembly.

Test the HDMI Port:

Power on the Xbox and test the HDMI port with a known-working cable and display. Ensure there is a proper connection and that audio and video signals are transmitted correctly.

If you are not confident in your soldering skills or if you encounter difficulties during the process, it's strongly recommended to seek professional help or contact Microsoft for repair options. Additionally, be aware that attempting to repair your Xbox One S Digital Edition on your own may void any existing warranties.

[applefixnz-blog]

Power & volume button not working | on off button repair | phone repairs experts | AppleFix |

power button and volume button not working. How to repair flex cable. mobile phone repairs in hamilton New Zealand. Oppo repairs, Huawei repairs, Nokia , samsung or any other brand.

Repairing or fixing the power on/off button on a mobile phone can be a complex task, as it often involves disassembling the phone and working with delicate components. If you're experiencing issues with your phone's power button, consider the following steps:

Basic Troubleshooting:

Ensure that the issue is with the power button and not a software problem. Sometimes, a simple restart or a software update can resolve power-related issues.

Clean the power button: Dust and debris can sometimes cause power buttons to become unresponsive. Carefully clean the button using compressed air or a small brush.

Restart Your Phone:

If your phone is still functional, try restarting it through the software settings, if possible. This can temporarily solve the problem if it's a software issue.

Check for Physical Damage:

Examine the power button and its surroundings for physical damage or debris that might be obstructing its operation.

Use Assistive Features:

Some mobile devices have built-in accessibility features that allow you to control power-related functions through the touchscreen. Check if your phone has this option.

Repairing or Replacing the Power Button (Advanced):

If you have experience with electronics repair and are comfortable disassembling your phone, you can attempt to repair or replace the power button.

You'll need the appropriate tools, a replacement power button, and a guide or tutorial specific to your phone model.

Be extremely cautious when disassembling your phone, as it can be easy to damage other components.

If you're not experienced with electronics repair, it's strongly recommended to seek professional repair services to avoid causing further damage to your phone.

Professional Repair Service:

The safest and most reliable option for fixing a power button issue is to take your phone to a professional repair technician like applefix in hamilton new zealand @. 125 ward street hamilton They have the expertise, tools, and replacement parts needed to address the problem effectively.

Contact the Manufacturer:

If your phone is under warranty, consider reaching out to the manufacturer's customer support for assistance and warranty repair options.

Remember that attempting a DIY repair on your phone may void your warranty or cause additional damage. It's essential to exercise caution and consider your level of expertise and the value of your device when deciding how to address a power button issue. If in doubt, consult with a professional technician or the phone manufacturer for guidance.

[applefixnz-blog]

Huawei Mediapad charging port repair & Disassembly | AGS2-W09 | Huawei repair Hamilton NZ AppleFix

Huawei repair experts in hamilton New Zealand. AppleFix Call 078394111 125 ward street hamilton New Zealand. Huawei mediapad AGS2-W09 broken charging port repair

We specialize in logic board and liquid damage repair and can fix your Laptop, MacBook, mobile phone , ipad, iphone , tablet , playstation, xbox or any other electronic gadget that has been deemed unfixable by another repair shop.

*Have a repair shop and are looking to outsource logic board repairs? We offer discounted repairs to other repair shops, schools, large organizations and government agencies. — https://applefix.co.nz/contact/

logicboard repair course in New Zealand

Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology.

This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment.  Start your own business or increase your chances to get job quickly.  https://applefix.co.nz/logicboard-repair-course/

 Mail in device info read here https://applefix.co.nz/send-your-device/

[applefixnz-blog]

Macbook Air water Damaged repair | A1931 CD3215C00 820-01521 | Macbook repair hamilton new zealand

Macbook Air water Damaged repair | A1931 CD3215C00 820-01521 | Macbook repairs Hamilton NZ |

Macbook repair Hamilton new zealand . how to replace pd controller?  Call 078394111 125 ward street hamilton new zealand

Macbook Air water Damaged repair | A1931 CD3215C00 u3200 | Macbook repair experts in Hamilton New Zealand. Type C power management IC

Logicboard repair courses

https://applefix.co.nz/logicboard-repair-course/

lcd refurbish courses

https://applefix.co.nz/lcd-refurbish-course/

[applefixnz-blog]

iMac wifi button grayed out | iMac Cross on wifi icon | iMac repairs hamilton nz AppleFix NZ

iMac a1418 a1418 not connecting to wifi or wifi is frayed out or cross on wifi connection. how to replace wifi module on imac. Full repair video

Applefix hamilton New Zealand imac repairs in hamilton nz

Call 078394111 125 ward street hamilton New Zealand

www.applefix.co.nz