katherinewangfs-blog

[katherinewangfs-blog]

What Is SFP Fiber Module?

Nowadays, almost all enterprise-class switches include two or more SFP (small form-factor pluggable) ports, allowing them to become part of a ring or star-based network topology spread among different buildings, floors or areas, and connected via fiber optic cabling. In many cases, SFP modules are also known as GBIC (mini-Gigabit interface converter) modules, as they have replaced the older GBIC transceivers. SFPs can be used and interchanged on a wide variety of products, and they can be either SFP fiber modules or SFP copper modules.

What Is SFP Fiber Module?

SFP fiber modules are connected by fiber optical cables, which are available with a variety of transmitter and receiver types, allowing users to select the appropriate transceiver for each link to provide the required optical reach over multimode fiber or single-mode fiber.

Optical SFP modules are commonly available in several different categories with different features:

For multi-mode fiber, with black or beige extraction lever; for single-mode fiber, with blue extraction lever

SX - 850 nm, for a maximum of 550 m at 1.25 Gb/s (Gigabit Ethernet) or 150m at 4.25 Gb/s (Fibre Channel)

LX - 1310 nm, for distances up to 10 km

BX - 1490 nm/1310 nm, Single Fiber Bi-Directional Gigabit SFP Transceivers, paired as BS-U and BS-D for Uplink and Downlink respectively, also for distances up to 10 km

1550 nm 40 km (XD), 80 km (ZX), 120 km (EX or EZX)

SFP Fiber Module Datasheet

With a wide application in optical network, many manufactures like Cisco and FS.COM provide a variety SFP modules. These models can be used on a wide variety of network equipment and intermixed in combinations of 1000BASE-T, 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX, 1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis. Part of the main products of Cisco SFP Fiber Modules are listed as below.

SFP Fiber Module vs SFP Copper Module

SFP port can be plugged in with both SFP fiber module and SFP copper module. The biggest difference between SFP fiber module and SFP copper module lies in the cabling method. As it has been mentioned before, a SFP fiber module runs on a optical fiber (SMF/MMF). While a SFP copper module works on a twisted copper cable (CAT5/CAT5a/cat6). Except for the cabling specification, their transmission distances and connectors are also different.

Summary

SFP module can connect various network devices such as switch, router, or fiber media converter to a fiber optic or copper networking cable. It is a popular industry format jointly developed and supported by many network component vendors. For SFP fiber module, it can transmit signal over a longer distance than SFP copper module. And the price for SFP fiber module is also cheaper than SFP copper module, so it gains more edges and popularity in the market of SFP modules.

[katherinewangfs-blog]

A Guide on Cisco SFP Port Configuration

We know that a SFP (small form-factor pluggable) transceiver is a compact, hot-swappable, input/output transceiver used in data communication and telecommunications networks. Many networks devices like switches, routers and fiber optic cables need SFPs to connect each other. Although everyone knows this is an important and essential component in optical communication system, many people are still unclear about its standard configuration, and don’t know how to install, remove, and maintain it correctly. Next we will Cisco SFP port configuration for three different types of Cisco SFP module respectively.

Cisco SFP Port Configuration for Mylar Tab SFP Module

Cisco SFP modules adopt different latching devices to secure and detach the Cisco SFP modules from the SFP port. The Mylar tab SFP module has a tab that you must pull to remove the module from a switching module port. To insert the Mylar tab SFP module into a switching module port, line up the Cisco SFP module with the port, and slide it into place.

To remove the Cisco SFP module from the switching module port, pull the tab gently in a slightly downward direction until it disengages from the port, and then pull the Cisco SFP module out.

Note: When pulling the tab to remove the Cisco SFP module, be sure to pull in a straight outward motion so that you remove the Cisco SFP module from the port in a parallel direction. Do not twist or pull the tab because you may disconnect it from the SFP module.

Cisco SFP Port Configuration for Actuator/Button SFP Module

The actuator/button SFP module has a button that you must push to remove the Cisco SFP module from a switching module port. To insert the actuator/button Cisco SFP module in to a switching module port, line up the Cisco SFP module with the port, and slide it in until the actuator/button clicks into place. Be sure not to press the actuator/button as you insert the Cisco SFP module because you might inadvertently disengage the Cisco SFP module from the port.

To remove an actuator/button SFP module from a switching module port, first you need to Gently press the actuator/button on the front of the Cisco SFP module until it clicks and the latch mechanism activates, releasing the SFP module from the port. And then grasp the actuator/button between your thumb and index finger, and carefully pull the Cisco SFP module from the port.

Cisco SFP Port Configuration for Bale-clasp SFP Module

The bale-clasp SFP module has a bale clasp that you use to secure the Cisco SFP module in a switching module port. To insert a bale-clasp Cisco SFP module into a switching module port, you need to close the bale-clasp before inserting the Cisco SFP module and then Line up the SFP module with the port, and slide it into the port.

To remove a bale-clasp SFP module from a switching module port, follow the next steps. Firstly, Open the bale clasp on the SFP module with your index finger in a downward direction. If the bale clasp is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver or other long, narrow instrument to open the bale clasp. Then, grasp the SFP module between your thumb and index finger, and carefully remove it from the switching module port.

Summary

It is important to follow the correct steps when making Cisco SFP port configuration, because that can protect your Cisco SFP mudule from getting damaged and ensure a high performance. Another caution needs to be mentioned here is that the invisible laser radiation may be emitted from disconnected fibers or connectors. So you need to avoid staring into beams or view directly with optical instruments.

[katherinewangfs-blog]

The Difference Between Cat5e vs Cat6 Patch Panel

To build a flexible and tidy cabling system. Patch panels are something we can never forget. The panel enables speedy UTP interconnections to hubs, routers, and other active equipment. Ethernet patch panel on the market comes in various types, such as 24 port patch panel or 48 port patch panel for Cat5e or Cat6 that is shielded or unshielded. So what’s difference between Cat5e Patch Panel and Cat6 Patch Panel? Can I use cat5e rated patch panel with cat6 cabling?

Cat5e vs Cat6 Patch Panel: To Know About Cat5e Patch Panel

Cat 5e patch panels meet the standards of TIA/EIA 568 industry specifications, which can help enhance the network performance in a maximum and keep up with the growing changes in your network. For now, there are many Cat 5e patch panel products that customers can pull off the shelf. Cat5e Ethernet patch panels from reliable supplier like FS are made from steel materials so that they can stand up even the most extreme conditions. With numbers labeled on ports, it’s easy for cable organization. FS Cat5e patch panels are available in 6-port and 8-port module groupings, in 8, 12, 24, and 48-port sizes. The high density panel design can be mounted to standard racks or cabinets, accommodate top, bottom or side cable entry, and also save valuable rack space.

Cat5e vs Cat6 Patch Panel: To Know About Cat6 Patch Panel

As it’s name suggests, Cat6 patch panels is specially designed for Cat6 cabling in 1 Gigabit Ethernet applications. With the help of these patch panels, you can achieve easy management and save data center rack space. They can meet or exceed the TIA/EIA 568 industry specification. All these Ethernet patch panels feature both T-568A and T-568B wiring configurations. Each patch panel terminates with standard 110 termination tools on the rear, which allows quick installations. Panels in FS cover 12, 24, 48, and 96-port configurations. Patch panels can be configured with six or eight port modules.

Cat5e vs Cat6 Patch Panel: Can I Run Cat6e on a Cat5e Patch Panel?

Actually, there isn't much practical difference in the Ethernet patch panels themselves. But there is a difference in the wire gauge specified between cat5/5e and cat6, and Cat6 wire gauge is typically larger which can be an issue when punching down on a 5e block. That’s to say:

When punching down Cat5/5e wire on a Cat6, the Cat5/5e wire is enough smaller that it is possible to get what looks like a good punch, but the insulation on the wire is not actually penetrated or is only partially penetrated by the vampire jaw of the punch block.

When punching down Cat6 wire on a Cat5/5e panel, the larger wire can end up bending or even breaking the vampire jaws on the punchdown block.

In both cases, using care and testing each connection, you can usually make it work. If your just doing one panel at home you are probably OK. However it wouldn't be recommended if doing several panels or working on an enterprise/commercial jobs that you plan to warrant the work.

[katherinewangfs-blog]

MTP vs MPO Connector for Dater Center’s High-density Demand

High density has been a hotly contested subject in the world of data centers for years. Today’s cyber world is moving ahead at an incredible speed, we’ve seen an unprecedented the demand for high-speed and high-density in data center. And 40Gb/s and 100Gb/s are more commonplace and now become a trend and hotspot for data-center cabling system. In such a circumstance, we can predict that MTP fiber connector and MPO fiber connector will eventually replace the standards for fiber optics as known.

MTP vs MPO Connector for High Density Needs

High density networking is based on two components. One, being able to have concentrated port density. Two, being able to have large numbers of fibre cores connecting nodes of the network. Most connectors (LC, SC, FC) have one fiber through them. The MTP/MPO connector has been designed as a “multi-fiber” connector. Going through the MTP connector wiki and MPO connector wiki, the MPO connector and subsequent standard were developed in the late 1980’s by the NTT-AT corporation. The MTP by US Conec corporation soon came after that with some additional features like a removable housing, elliptically shaped alignment pins, and the ability to change the connector’s gender. Current MPO connectors now offer these features. The main thing to remember is that the MTP connector adheres to the MPO standard. Therefore, MTP and MPO connectors are interchangeable.

The MTP connector is the same size as a traditional SC connector. However, the MTP connector has 12 fibers to the SC’s one fibre. This 12 fold increase in density enables a much greater port density at any point on the network. There are also 24 fibre and 48 fibre connectors within the MTP range that are also the same size as an SC connector.

MTP vs MPO for Multi-Fiber Solution

The MPO fiber connector and MTP fiber cable connector can offer up to 12 times the density of standard connectors, providing significant space and cost savings. Due to this fact and its excellent performance in various applications, many manufacturers now offer a wide range of MTP/MPO products, such as MTP / MPO Cable Assemblies, Fanout / Breakout Cables, MTP / MPO Trunk Cables, MTP / MPO Fiber Optic Plug-N-Play Cassettes, MTP / MPO Adapters, MTP / MPO Fiber Optic Loopbacks and etc.

With its higher port density, MTP/MPO fiber is easier to install - just pull 1 cable with 12, 24, or more fibers for one easy plug-in. Delivers big savings in installation time and cost. And High density MTP/MPO trunk cables can come with up to 288 fibers in a single cable.

Summary

MPO fiber connector and MTP fiber cable connector offer ideal solution to set up a high-density and high-performance data networks with the advantages of time saving and cost saving. Considering the huge benefits it they have brought and their special role in the migration to 40/100 Gigabit Ethernet, MTP/MPO connector will definitely gain more and more popularity among data centers.

[katherinewangfs-blog]

Do You Really Need a White Box Switch？

Although white box switches have been emerged for years, many people still tend to consider switches first from branded companies first when buying a fiber optic switch. The adoption of white box switch has been limited to niche companies that have large engineering departments. Over the years, the market of fiber optic market has been dominated by select vendors like Cisco, HP, Arista and Juniper. However, white box switch is coming to break the ice.

White Box Switch: What’s It?

The phrase "white box" has long been used to apply to no-name computers. The same ODMs (original design manufacturers) that produced them are getting into the game of manufacturing white-box switches. White-box switches look just like any other switch, but they are not installed with operating systems (OS). Since every switch needs an operating system, white box switches are useless without software. The OS can be chosen by the customers based on their actual needs. This OS needs to seamlessly integrate with existing L2/L3 topologies and support a basic set of features. Beyond this, there should be new capabilities delivered as a result of "opening up" the network switch. Also many third party provide white box switches that are already operating systems like ICOS or Cumulus while they are rolling off the production line.

White Box Switch: What Makes It Superior over Traditional Switch

Despite the fact that the use of white box switches has been limited for a couple of reasons, such as customer worries for product quality and technical support, white box switches have come a long way from where they were. And I believe they are now ready for a broader market. I know some of you may doubt it and think it is not the one for you when buying a gigabit ethernet switch. But if you dig into it, you can see the white boxes have improved significantly in the following areas:

1. High flexibility, as their main function is to meet the data demands.

2. These are helpful to provide efficiency and productivity to the business.

3. Lower operating cost.

4. Lower capex Methods.

5. Less costs than equivalent speed switches.

6. White box switches are open networking switches.

7. The SDN controller is accountable for centralizing the network.

8. White box switching software can be easily attainable through any reseller or partner directly.

Summary

Maybe a white box gigabit switch is not the best gigabit switch in your heart right now, it is still undeniable that white box switch will be the future trend for data center siwtches. Many mainstream networks vendors also began to provide white box switches. Also, these will come shipped with tried-and-true network operating systems from vendors such as Pica8 and Cumulus.

[katherinewangfs-blog]

Datasheet of 40G QSFP Module

When it comes to selecting 40G QSFP modules, customers may be dazzled by the various products provided by various suppliers. Some of them may directly purchase from big brands like Cisco. Actually, except for those well known brands, many other rising companies like FS also provide 40G QSFP transceivers, which usually come at a much lower price with with a high quality. This post will demonstrate the 40G QSFP Datasheet provided by FS.

40G QSFP Datasheet: QSFP 40G SR4 Datasheet

The S-Class FS 40GBASE-SR4 QSFP module supports link lengths of 100 and 150 meters, respectively, on laser-optimized OM3 and OM4 multimode fibers. QSFP 40G SR4 transceiver is aligned to IEEE 40GBASE-SR4 optical specifications which support high-bandwidth 40G optical links over 12-fiber parallel fiber terminated with MPO/MTP multifiber female connectors. Because IEEE 40GBASE-SR4 does not support 4x10G breakout connectivity to 10GBASE-SR, see QSFP-40G-SR4 or QSFP-40G-CSR4 for such applications. QSFP 40G SR4 does not support FCoE. More specific details of FS QSFP 40G SR4 Datasheet can be obtained in the table below.

40G QSFP Datasheet: QSFP 40G LR4 S Datasheet

The FS 40GBASE-LR4 QSFP module supports link lengths of up to 10 kilometer over a standard pair of G.652 SMF (single-mode fiber) with duplex LC connectors. The QSFP-40G-LR4-S module supports 40GBASE Ethernet rate only. The 40 Gigabit Ethernet signal is carried over four wavelengths. Multiplexing and demultiplexing of the four wavelengths are managed in the device. QSFP-40G-LR4-S does not support FCoE. More information have been shown in the following QSFP 40g LR4 S Datasheet.

QSFP+ SR4 vs QSFP+ LR4: Which One to Choose?

After going through QSFP 40G SR4 Datasheet and QSFP 40g LR4 S Datasheet, you may have had a basic understanding of QSFP 40G SR4 and QSFP 40g LR4. SR is short for short reach and LR represents Long Reach. The most obvious difference is that 40GBASE-SR4 is with MPO/MTP port while the 40GBASE-LR4 is with the Duplex LC port. The cost of 40GBASE-SR4 QSFP+ is more cheaper than the 40GBASE-LR4 QSFP+. Additionally, the fiber cost of the cabling with them also have a big difference. Because SMF cabling is more expensive than the MMF cabling.

Summary

As speeds have increased to 40G, the quad small form-factor pluggable (QSFP) has become the high-density transceiver of choice. Hoping this post on FS 40G QSFP Datasheet may help you when selecting 40G optical transceivers.

[katherinewangfs-blog]

Analysis of Power Budget and Link Distance in CWDM System

It can’t be denied that CWDM technology is a cost effective method to increase the capacity in the existing system, which can give different wavelengths to multiple optical signals and multiplex them for transmission through only one single fiber. Different from the DWDM system, the network using CWDM technology are deployed by passive components like passive CWDM Mux Demux, without the need of additional power, which makes CWDM system more commonly used. Do you also plan to build a CWDM system? If yes, you can check the following information for reference, which mainly analyzes the optical power budget in a CWDM system and calculates the CWDM link distance according to the power budget for smoothly deploying a CWDM system.

What’s Optical Power Budget?

Before deploying an optical network, it is very essential to calculate the optical power budget for better deployment. What’s optical power budget? It is just the amount of light available to make a successful fiber connection which can be calculated by analyzing the original output power of the transmitter and the required input power of the receiver. In details, we should firstly learn the optical power that is emitted by the source (also referred to Transmit Power) and the required power of the detector (also called Receiver Sensitivity). Using the first data to subtract the second one, you’ll get the data of the optical power budget which greatly determines the performance of the whole network link.

Here is the equation: Optical Power Budget = Transmit Power - Receiver Sensitivity.

How to Get the Optical Power Budget in a CWDM System?

To estimate the link distance supported by a CWDM system, the optical power budget should be calculated first, which can greatly determine the CWDM link distance. Here will show you a basic CWDM system under an ideal condition to clearly illustrate how to get the optical power budget. In this basic CWDM system, there is a optical transmitter which transmit power is -2 dBm and a optical receiver with -25 dBm receiver sensitivity. Hence, the optical power budget is 23 dB, as shown in the following equation.

Optical Power Budget = Tx Power - Rx Sensitivity = -2 dBm - (-25 dBm) = 23 dB

However, the mentioned CWDM system is just under an ideal condition without loss caused by the signal transmission. In a normal CWDM system, there are many components like passive CWDM Mux Demux, CWDM transceiver inserted. All these components cause insertion loss once they are inserted into the CWDM link. Therefore, when doing the optical power budget, all the loss should be taken into account for calculating the power budget exactly.

Here is more exact equation: Power Budget = Tx Power - Rx Sensitivity - Loss

To get the real power budget of a CWDM system, here offers a simple CWDM link which uses the -2 dBm optical transmitter, -25 dBm optical receiver and four passive CWDM Mux Demux with low insertion loss. Both the stable 4 channel CWDM Mux and stable 4 channel CWDM Demux in the link have 2.0 dB insertion loss, and other two are 8 channel ones feature 2.5dB insertion loss separately, as shown in the figure below. As a result, the total loss caused by the four passive CWDM Mux Demux is 9 dB, resulted from 2.5 dB + 2.0 dB+2.5 dB + 2.0 dB. Then we can get the total power budget, 14 dB. The calculation process is: Power Budget = Tx Power - Rx Sensitivity - Loss = -2 dBm - (-25 dBm) - 9 dB = 14 dB

How to Calculate the Link Distance in the CWDM System?

After knowing the optical power budget, let’s calculate the link distance of the CWDM system according to the following equation: Link Distance = Optical Power Budget/Fiber Attenuation. As there may be some other power loss caused by the factors that we didn’t consider like fiber aging, temperature and poor splice, we often subtract 2 dB buffer from the total optical power budget. Meanwhile, the fiber attenuation is changeable according to the wavelength, usually varying from 0.2 to 0.35 dB/km. In this case, we’ll use 0.35 dB/km as a typical data. Then we can get the link distance is about 34 km. The calculation process is Link Distance = Optical Power Budget/Fiber Attenuation = (14 dB- 2 dB)/0.35 dB/km.

Conclusion

This paper intends to illustrate how to calculate the optical power budget and estimate the link distance of a CWDM system according to the optical power budget, which allows for better budget of deploying the CWDM system and eliminates the unwanted or unnecessary issues which may happen in the system deployment. Besides, if you want to make a cost effective CWDM system, you are suggested to buy CWDM components like cheap passive CWDM Mux Demux, CWDM transceivers from FS.COM, which are of good price and quality.

[katherinewangfs-blog]

What Can CATV Systems Benefit from EDFA Optical Amplifiers?

As long-distance transmissions are always required in the CATV systems, it is very necessary to make the quality of visual and audio signals in high levels after the long transmissions, so that the performance of the CATV systems can be ensured. To serve this aim, the CATV EDFA optical amplifiers are come up with and widely used in the CATV systems. Why the EDFA optical amplifier is needed in CATV system? How does it work for the long CATV application? The following text will give you the answers and simply introduce two typical CATV EDFA amplifier applications for your reference.

What’s CATV EDFA Amplifier?

CATV EDFA is a kind of optical amplifier, most commonly used in the long-haul CATV system for boosting the damped CATV signals, with the aim of compensating the signal loss. Since it mostly works as booster optical amplifier in the CATV system, so that it can be also called CATV booster amplifier. By utilizing the CATV EDFA optical amplifier, the CATV signals can be enhanced to meet the system requirement and then be sent to the users. However, when the signal power is improved by the CATV EDFA, the noise existing in the transmission link would also boosted and some return loss would also occur at the same time. Considering that, it is very necessary to choose quality CATV EDFA optical amplifier for ensuring the performance of CATV system, even if it may be cost a little higher than common optical amplifier.

Why CATV EDFA Optical Amplifier is Used?

CATV is a multi-channel TV system transmitting visual and audio signals from digital or analog television and radio channel to many users via fiber or copper patch cable. As the signals should be finally separated by optical splitter to serve more than one users and many loss has occurred in the long transmission, the overall speed and quality of the CATV signals would become too weak to meet the receiver requirements. Under this condition, the CATV EDFA optical amplifier is very essential for CATV system with the function of amplifying CATV signals and giving high performance systems to the users.

How Does CATV EDFA Work for Long CATV Applications?

A long CATV system is always composed of head end, transmitter, receiver, CATV booster amplifier and optical splitter. When the system runs, the CATV signals are provided by the head end, and need to be split into several signals by the optical splitter to serve the users. When the signals pass through the optical splitter, the signal power would be in a very low level. Hence, the CATV EDFA optical amplifier should be deployed after the receiver to improve the signal power, and the users can finally receive quality signals.

From the figure above, we can learn a simple point-to-multipoint CATV network design as mentioned above. The CATV signals are provided by the RF combiner and should be connected with four receivers by the optical splitter. In order to compensating the signal loss caused by the optical splitter, CATV EDFA optical amplifier is required before sending the weak signals to the users.

Except for this simple kind of CATV network using CATV EDFA optical amplifier, here also offers a complex CATV network, as designed in the figure below. In this CATV network, the CATV EDFA optical amplifier is deploy behind the 8 channel DWDM Mux Demux to amplify the signals while the 8 channel DWDM Mux Demux allows for higher capacity transmission. Hence, a long CATV network with big capacity can be achieved.

Conclusion

When deploying a long CATV system, we should pay attention to the loss caused by long transmission distance and CATV components. When the loss is very high, CATV EDFA optical amplifier would be an ideal device deployed in the long CATV system for improving the quality of CATV signals, so that the users can receive high speed and reliability of the services.

[katherinewangfs-blog]

EDFA Amplifiers for Building Long-haul DWDM Networks

Clearly different from the traditional repeater, the EDFA amplifier doesn’t need to convert the optical signals into electrical ones, then make the electrical amplification and finally convert the amplified electrical signals into amplified optical signals again. It is an optical amplifier that can directly enhance the optical signals without making additional conversion. By using the EDFA optical amplifier, the attenuated signal power can be amplified into strong signal level to meet the requirement of the long-haul applications, especially the long-haul DWDM networks. To better understand the function of EDFA amplifier, the following will mainly study the working principle of EDFA amplifier works and illustrate how to use it to build the long DWDM network.

What’s the Working Principle of EDFA Amplifier?

From the figure below, we can learn the basic configuration of the EDFA amplifier, mainly composed of a length of EDF (erbium doped fiber), a pump laser with 980 nm or 1480 nm, a pump combiner and a simple WDM system. When the attenuated signals around 1550 nm pass through an EDFA amplifier, a pump laser will be generated. Then the DWDM signals and pump laser will be combined by the pump combiner. When they come into the EDF together, the wavelengths of signals and pump laser will be multiplexed and the interaction with the doping ions would enhance the signal power into high level. Thereby, a longer DWDM transmission can be reached.

How to Use EDFA Amplifier for Long DWDM network?

In a long DWDM network, the EDFA amplifier can be put in three different places with different aims. Firstly, we can put it in the transmitter side of the DWDM link to offer high input signal power, so that the DWDM fiber link can be extended. If the EDFA amplifier is deployed in this place, we can also call it EDFA optical booster amplifier. Secondly, we can also place the EDFA amplifier in the receiver side of the DWDM link as optical preamplifier, hence the output signal power can be boosted to meet the necessary receiver level. Finally, when the fiber loss in the transmission process is too high to support the long DWDM network, we can deploy the EDFA amplifier in any intermediate point along the long fiber link to compensate the fiber loss. And this time, we can call it EDFA optical in-line amplifier.

Analysis of Practical Long DWDM Cases with EDFA Amplifiers

Case One: in this case, EDFA optical booster amplifiers are deployed at both transmitter sides of the dual-way DWDM links. We can learn it from the figure below. Two 40 channel DWDM Mux Demux are deployed to multiplex 40 1G signals. Then the two integrated 40G signals from both sides are enhanced by the booster amplifier and can be transmitted up to 170 km over each single fiber.

Case Two: as shown in the following figure, except for the booster amplifiers, EDFA optical optical preamplifiers are also placed at both receiver sides of the dual-way DWDM links. By adding the optical preamplifiers to the CWDM link, the transmission distance is finally extended from 170 km to 200 km.

Case Three: it is highly noted from the following figure that the DWDM transmission distance can be up to 400 km. How to achieve this? Just putting the EDFA amplifiers in the three places mentioned above. As deployed in the figure, a pair of EDFA optical booster amplifiers, optical preamplifiers and optical in-line amplifiers are used for the 400km transmission.

Case Four: If the distance of 400 km still cannot meet our requirement, we can set up more repeater sites to place other optical in-line amplifiers. At present, using these three kinds of EDFA amplifiers already enables 100Gbps bandwidth for realizing up to 1000 km in a point-to-point connection, as shown in the figure below.

Conclusion

When designing a long-haul DWDM network for transmitting big data, EDFA amplifier is an ideal solution for current and future optical system which should be taken into consideration. It can be deployed at the transmitter side, the receiver side and any intermediate point along the DWDM long fiber link, as optical preamplifier, booster amplifier and in-line amplifier, for enhancing the signal power, thereby a long-haul transmission can be deployed.

[katherinewangfs-blog]

Why Not Build a 10G CWDM Network for Higher Capacity?

Although the 40G and 100G technologies develop vigorously recent years to meet the increasing need of higher capacity, they are still not widely accepted and applied due to high deploying cost. Under this case, choosing to build a 10G network is always the first choice for most users. But except upgrading our system, what else can we do when the 10G network can’t offer enough capacity? To address this issue, telcom engineers and researchers suggest that we can deploy the 10G CWDM networks. With use of CWDM optical multiplexer, this solution offers a highly cost effective method to gain more capacity on the basis of 10G network. Let’s study the benefits of 10G CWDM network and its two basic common network infrastructures in details.

What Can We Benefit from 10G CWDM Network?

In contrast to 10G DWDM network, 10G CWDM network can neither offer so high data capacity nor transmit the signals so long. But on the other hand, 10G CWDM network is an easier-to-deploy and less expensive solution that can well serve for a wide range of optical applications. Let’s study the main benefits of 10G CWDM networks.

It is possible to add connections for transmitting more data in 10G network, which makes the whole network load increasing from 10G to 40G or 100G possible.

CWDM Mux Demux is the key component of 10G CWDM network. As a passive component, it doesn’t require extra power, which is an ideal option for deploying 10G CWDM network.

Instead of upgrading system, deploying 10G CWDM network to get more capacity can saves a lot of money due to the economical 10G hardware and cheap passive CWDM Mux Demux.

Understanding Common 10G CWDM Network Infrastructures

10G CWDM system is a passive optical network, which supports 10G transmission with any protocol over the optical link, as long as the 10G signals are at the specific CWDM wavelengths. At present, there are two common CWDM network infrastructures. One is 10G CWDM point-to-point network, and the other is 10G CWDM ring network. The following will introduce the two common infrastructures in details.

10G CWDM Point-to-Point Network: it is the simplest network infrastructure of the CWDM networks. As shown in the following figure, there are two passive CWDM Mux Demux deployed in the 10G network that offers 8 channels to multiplex the signals from 8 different optical fiber link into an integrated signal. Thereby, the signal can be transmit through only one fiber, which means there are 7 virtual fiber created with higher capacity for transmitting more data. As for the cheap passive CWDM Mux Demux, it can be available at very good price that costs less than upgrading the system from 10G to 40G or 100G. Undoubtedly, deploying a 10G CWDM point-to-point network is very economical solution for higher capacity.

10G CWDM Ring Network: it is deployed on the basis of 10G CWDM point-to-point network. Compared to point-to-point network, the ring network is much more complex that needs other optical CWDM components like CWDM OADM. By adding CWDM OADM, two or more point-to-point network can be connected together, which can finally achieve a 10G CWDM ring network. To better understand how does the 10G CWDM ring network work, here offer a figure that shows four buildings are connected by several 8 channels CWDM Mux Demux and CWDM OADM for your reference.

Conclusion

Unlike upgrading the network from 10G to 40G or 100G, building a 10G CWDM network doesn’t requires changing all the network equipment which may cost highly. It only need CWDM transceiver and CWDM Mux Demux to be deployed in the original 10G network. For a complex 10G CWDM network, additional optical equipment like CWDM OADM are required. If you come across the capacity-hungry issue, building a 10G CWDM network would be a nice option for higher capacity.

[katherinewangfs-blog]

How to Extend Your Network Transmission Distance?

To face the need for long-haul, high-capacity transmission, experts come up with several DWDM projects including DWDM Mux Demux, EDFA amplifier (erbium-doped fiber amplifier) and DCM module (dispersion compensation module) to expand network capacity and enhance the signal power, which can greatly extend the optical network reach. Do you have the need to deploy a longer fiber optical transmission link? If yes, you can just build a DWDM system with the DWDM projects mentioned above. This paper will introduce three solutions that utilize these DWDM components to extend the optical network transmission distance. Hope these DWDM solutions would be useful for you.

Using DWDM Mux Demux for Long Transmission up to 50 km

DWDM technology plays an important role in building long-haul transmission system, which enables multiple signals with different wavelengths to be transmitted through only one single fiber. To build a long system with DWDM technology, the DWDM Mux Demux is an indispensable component that features low insertion loss and polarization-dependent loss. By using the DWDM Mux Demux in your network, the signal transmission distance can be extended to up to 50 km. To better know the advantage of DWDM Mux Demux, here offers an example that uses two 8 channel DWDM Mux Demux for extending the optical fiber link.

From the figure, we can learn that at the transmit side, eight kinds of signals from different fiber links are multiplexed into an integrated signal by the 8 channel DWDM Mux. Then the integrated signal is transmitted over the single mode fiber (SMF) and the maximum transmission distance can be up to 50 km. At the receiver side, the signal will be demultiplexed into individual signals with their original wavelengths by the 8 channel DWDM Demux and then transmitted to another eight different fiber links. Just by using the DWDM Mux Demux, a 50km long-haul transmission can be simply achieved.

Adding EDFA Amplifier for Transmission Longer Than 50 km

As we know, the longer the transmission distance is, the higher the fiber loss will be. Hence, except for the DWDM Mux Demux, you are suggested to add an EDFA amplifier to the long fiber link if the transmission distance is longer than 50 km. What’s the function of EDFA amplifier? It is mainly designed to amplify the signal power, which enables longer transmission. As shown in the following figure, you can learn that the only difference is the EDFA amplifier in the SMF, compared to the first solution.

When the integrated signal multiplexed by the 8 channel DWDM Demux is transmitted over the SMF, it would become too weak in the transmission process to be transmitted. Then the EDFA amplifier should be placed there to boost the signal power, supporting the transmission longer than 50 km. Once the long transmission is realized, the signal will be also split by the 8 channel DWDM Demux, like the first solution. In short, DWDM Mux Demux and EDFA amplifier are highly suggested if you want to deploy a DWDM system longer than 50 km.

Adding DCM Module for Transmission up to 200 km

With the use of EDFA amplifier, the DWDM fiber link can be extended to 200 km. However, the signal quality is always unsatisfied due to the optical dispersion in long transmission, especially in CATV systems. To meet high requirements of the signal quality in these long transmission systems, an additional optical component, DCM module are needed in the long fiber link, as deployed in the figure below.

From the figure, we can learn it is a long-haul point-to-multipoint CATV system. To extend the transmission distance, 8 channel DWDM Mux Demux, EDFA amplifier are used. Except for that, a DCM module is added to enhance the skew signal for ensuring the whole transmission quality. With the use of DCM module, the accumulated chromatic dispersion issue is solved, without dropping and regenerating the wavelengths on the long fiber link. Thereby, a high-performance 200km system can be reached.

Conclusion

DWDM projects including DWDM Mux Demux, EDFA amplifier and DCM module are key optical components to support long-haul transmission systems. If you want to deploy a long transmission system up to 50 km, then the DWDM Mux Demux is needed. For transmission longer than 50 km, both the DWDM Mux Demux and EDFA amplifier are required for boost the signal power. But once the transmission distance is about 200 km, you should additionally add the DCM module to enhance the signal quality.

[katherinewangfs-blog]

Whether to Use EDFA Amplifier in Long WDM System Or Not?

Currently, utilizing WDM technology to deploy the optical network has received widespread attentions, which enables higher capacity for data transmission. However, the technology is also limited by the transmission distance. When deploying a long WDM system, the signal power would still become weak due to the fiber loss. In order to address the issue, using EDFA amplifier to directly enhance the WDM signals would be a good choice for current and future optical network needs. The optical network combining WDM technology and EDFA module together can transmit multiple signals over the same fiber, at lengths up to a few hundred kilometers or even transoceanic distances. To better know how does EDFA amplifier work in the long WDM system, let’s learn the EDFA amplifier knowledge and analyze the performance of WDM system bonding with the EDFA module.

Introduction to EDFA Amplifier

EDFA amplifier, also referred to as erbium-doped fiber amplifier, is basically composed of a length of Erbium-doped fiber (EDF), a pump laser, and a WDM combiner. When it works, the pump laser with 980 nm or 1480 nm and the input signal around 1550 nm can be combined by the WDM combiner, then transmitted and multiplexed into the Erbium-doped fiber for signal amplification. The pump energy can be transmitted in the same direction as the signal (forward pumping), or the opposite direction to the signal (backward pumping), or both direction together. And the pump laser can also using 980 nm or 1480 nm, or both. Taking the cost, reliability and power consumption into account, the forward pumping configuration with 980nm pump laser EDFA amplifier is always the first choice to enhance the signals for a long WDM system.

Analysis of WDM Network Without EDFA Amplifier

Before analyzing WDM network deployed with EDFA amplifier, it is necessary to know the basic configuration of an original WDM network, as shown in the figure below. We can learn that four signals from different channels are combined by the optical combiner. And then, the integrated signals are transmitted through an optical fiber. Thirdly, the signals are split into two parts by the splitter. One part passes through the optical spectrum analyzer for analyzing signals, and the other one goes through the photo detector to be converted into electrical signal and then be observed by the electrical filter and scope. However, in the process, the signal power gets highly attenuated after being transmitting at long distance.

Analysis of WDM Network Using EDFA Amplifier

By using the EDFA amplifier, we can easily overcome the attenuation of long WDM network. From the following figure, we can learn that EDFA amplifiers act as booster amplifier and pre-amplifier to enhance the signal, so that system will no longer suffer from losses or attenuation. Therefore, if you need to deploy a long WDM system, it is highly recommended to deploy the EDFA amplifiers in the system that features flat gain over a large dynamic gain range, low noise, high saturation output power and stable operation with excellent transient suppression. It is an undoubtedly ideal solution with reliable performance and relatively low cost to extend the WDM network transmission distance.

Conclusion

It is well know that the signal power would be greatly attenuated when the transmission distance is long enough. Hence, when deploying a long WDM network, it is definitely necessary to use the EDFA amplifier to enhance the signal strength, allowing for the long transmission distance. As a preferable option, the EDFA amplifier with very low noise is relatively insensitive to signal polarization and easy to realize signal amplification.

[katherinewangfs-blog]

EDFA vs Raman Optical Amplifier

Although the fiber loss limits the transmission distance, the need for longer fiber optical transmission link seems never ending. In the pursuit of progress, several kinds of optical amplifiers are published to enhance the signals. Hence, longer fiber optical transmission link with big capacity and fast transmission rate can be achieved. As the EDFA and Raman amplifiers are the two main options for optical signal amplification. which one should be used when designing long fiber optical network? What are the differences of the two optical amplifiers? Which one would perform better to achieve the long fiber optical link? And which one is more cost effective? Let’s talk about this topics.

What’s EDFA Amplifier?

EDFA (Erbium-doped Fiber Amplifier), firstly invented in 1987 for commercial use, is the most deployed optical amplifier in the DWDM system that uses the Erbium-doped fiber as optical amplification medium to directly enhance the signals. It enables instantaneous amplification for signals with multiple wavelengths, basically within two bands. One is the Conventional, or C-band, approximately from 1525 nm to 1565 nm, and the other is the Long, or L-band, approximately from 1570 nm to 1610 nm. Meanwhile, it has two commonly used pumping bands, 980 nm and 1480 nm. The 980nm band has a higher absorption cross-section usually used in low-noise application, while 1480nm band has a lower but broader absorption cross-section that is generally used for higher power amplifiers.

The following figure detailedly illustrates how the EDFA amplifier enhance the signals. When the EDFA amplifier works, it offers a pump laser with 980 nm or 1480 nm. Once the pump laser and the input signals pass through the coupler, they will be multiplexed over the Erbium-doped fiber. Through the interaction with the doping ions, the signal amplification can be finally achieved. This all-optical amplifier not only greatly lowers the cost but highly improves the efficiency for optical signal amplification. In short, the EDFA amplifier is a milestone in the history of fiber optics that can directly amplify signals with multiple wavelengths over one fiber, instead of optical-electrical-optical signal amplification.

What’s Raman Amplifier?

As the limitations of EDFA amplifier working band and bandwidth became more and more obvious, Raman amplifier was put forward as an advanced optical amplifier that enhances the signals by stimulated Raman scattering. To meet the future-proof network needs, it can provide gain at any wavelength. At present, two kinds of Raman amplifiers are available on the market. One is lumped Raman amplifier that always uses the DCF (dispersion compensation fiber) or high nonlinear fiber as gain medium. Its gain fiber is relatively short, generally within 10 km. The other one is distributed Raman amplifier. Its gain medium is common fiber, which is much longer, generally dozens of kilometers.

When the Raman amplifier is working, the pump laser may be coupled into the transmission fiber in the same direction as the signal (co-directional pumping), in the opposite direction (contra-directional pumping) or in both directions. Then the signals and pump laser will be nonlinearly interacted within the optical fiber for signal amplification. In general, the contra-directional pumping is more common as the transfer of noise from the pump to the signal is reduced, as shown in the following figure.

EDFA vs Raman Optical Amplifier: Which One Wins?

After knowing the basic information of EDFA and Raman optical amplifiers, you must consider that the Raman amplifier performs better for two main reasons. Firstly, it has a wide band, while the band of EDFA is only from 1525 nm to 1565 nm and 1570 nm to 1610 nm. Secondly, it enables distributed amplification within the transmission fiber. As the transmission fiber is used as gain medium in the Raman amplifier, it can increase the length of spans between the amplifiers and regeneration sites. Except for the two advantages mentioned above, Raman amplifier can be also used to extend EDFA.

However, if the Raman amplifier is a better option, why there are still so many users choosing the EDFA amplifiers? Compared with Raman amplifier, EDFA amplifier also features many advantages, such as, low cost, high pump power utilization, high energy conversion efficiency, good gain stability and high gain with little cross-talk. Here offers a table that shows the differences between EDFA and Raman optical amplifiers for your reference.

Considering that both EDFA and Raman optical amplifiers have their own advantages, which one should be used for enhancing signals, EDFA amplifier, Raman amplifier or both? It strictly depends on the requirement of your fiber optical link. You should just take the characteristics of your fiber optical link like length, fiber type, attenuation, and channel count into account for network design. When the EDFA amplifier meets the need, you don’t need the Raman amplifier as the Raman amplifier will cost you more.

Original source: http://www.chinacablesbuy.com/edfa-vs-raman-optical-amplifier.html

[katherinewangfs-blog]

How to Enhance the Optical Signals for a Long DWDM System?

As we know, the longer the optical transmission distance is, the weaker the optical signals will be. For a long DWDM system, this phenomenon easily causes transmission error or even failure. Under this case, what can we do for a smooth, long DWDM system? The answer is optical signal enhancement. Only by enhancing the optical signals, can the DWDM transmission distance be extended. In this post, we are going to learn two effective solutions, optical amplifier (OA) and dispersion compensating module (DCM) to enhance the signals, for making a smooth, long DWDM system.

Optical Amplifier Solution

We used to utilize repeater to enhance the signals in fiber optics, which should firstly convert the optical signals into an electrical one, amplify the electrical signals, and then convert the electrical signals into an optical one again. Finally, you can get the enhanced optical signals. However, this method of enhancing signals can not only cause more signal loss, but also add unwanted noises in the actual signal. Taking these issues into account, the optical amplifier is more recommendable.

An optical amplifier is a device that enables direct optical signal enhancement or amplification. Its working principle is not so complicated as that of the repeater, while its performance is much higher. From the following figure, we can learn that the original reach of the DWDM system is limited to 80 km due to the signal loss. But with the optical amplifier, the signals are enhanced and the reach can be extended to 160 km. It is really an ideal option to enhance the signals for a long DWDM system.

At present, there are mainly three major kinds of optical amplifiers, Semiconductor Optical Amplifier (SOA), Doper Fiber Amplifier (DFA), and Raman Amplifier (RA).

Semiconductor Optical Amplifier: as its name implies, the semiconductor in a SOA is used to offer the gain medium. This kind of optical amplifier has a similar structure to the FP laser diode. However, it is designed with anti-reflection elements at the end face that can greatly reduce the end face reflection. Meanwhile, the SOA features small package and low cost that suits for most users to enhance the optical signals.

Doper Fiber Amplifier: in a DFA, the doped optical fiber acts as the gain medium for signal amplification. When the DFA works, the signal to be amplified and a pump laser are multiplexed into the doped fiber. And then the signal is amplified through interaction with the doping ions. The most common DFA is the Erbium Doped Fiber Amplifier (EDFA). Its gain medium is a optical fiber doped with trivalent erbium ions that always enhances the signals near 1550nm wavelength. Undoubtedly, the EDFA is a great choice to enhance the optical signals.

Raman Amplifier: different from the SOA and DFA, the signal in a RA is amplified through the nonlinear interaction between the signal and a pump laser within an optical fiber. In details, two kinds, distributed and lumped Raman amplifier (DRA and LRA) are available on the market. The distributed one multiplexes the pump wavelength with signal wavelength through the transmission fiber to enhance the signals, while the amplification of the lumped one is provided by a dedicated, shorter length of fiber.

Dispersion Compensating Solution

Apart from signal amplification, we can also use dispersion compensation to enhance the optical signals. Once the dispersion occurs, the signal will be tended to skew due to the different frequencies, which has a negative effect on the quality of signal transmission. At that moment, we use the dispersion compensating module to enhance the skew signal, for achieving a longer transmission distance. As shown in the figure below, the DWDM system is extended to longer than 80 km with the use of 80km passive dispersion compensating module.

The dispersion compensation module is an important component for a long fiber optical link. It typically connects to the mid-stage of an OA like EDFA, in the long haul transmission system. Except for the 80km DCM mentioned above, FS.COM also provides other DCM modules that allow long transmission distance extension. The compensation distances can range from 10km to 140 km, as shown in the following table.

Conclusion

The optical amplifier has the ability to directly boost the weak signal, while the dispersion compensation module can reshape the deformed signal and offer a long compensation distance. Considering that the signal strength would become weak as the transmission distance increases, using the optical amplifier and dispersion compensation module to enhance the signals is very necessary when building a long DWDM system.

Original source: http://www.chinacablesbuy.com/enhance-optical-signals-long-dwdm-system.html

[katherinewangfs-blog]

Economical Solutions for 10G to 40G Connection

With the accelerated development of optical network, there exist more and more capacity-hungry applications in 10G networks today. To solve this problem, experts put forward the 10G to 40G connection as an ideal solution. However, due to the high migration cost, we are prevented from making the migration. Do you also meet this issue? In this paper, it will offer several solutions for making 10G to 40G connections with less cost. Hope you can find one that suits your network.

Economical Solutions for 10G to 40G Short Connection

How to make a short link between 10G and 40G switches? You can choose the 40GBASE-SR4 QSFP+ module that supports the 40G network at length up to 150 m. Meanwhile, four 10GBASE-SR SFP+ modules are required. So is the MTP-LC harness cable for connecting QSFP+ and four SFP+ modules. In details, FS.COM offers OM3 MTP-LC harness cable supporting 40G connection up to 100 m and OM4 up to150 m. All these equipment mentioned above are available at FS.COM with good prices. For the details, you can learn from the following table.

If the link distance is longer than 150 m in your network, 40GBASE-CSR4 QSFP+ module may be a better choice. It can transmit the 40G signals longer, up to 400 m. As for the fiber patch cable, you can still chosse OM3 or OM4 MTP-LC harness cable. In general, the OM3 provided by FS.COM enables the connection up to 300 m, while OM4 up to 400 m. When making a short 10G to 40G migration, you can just choose FS.COM as an ideal fiber optical manufacturer. It offers all the equipment your network needs, including 10G and 40G switches, SFP+ and QSFP+ module and MTP-LC patch cable.

Economical Solutions for 10G to 40G Long Connection

Do you need to make a long 10G to 40G migration? FS.COM also offers several cost effective solutions. For example, up to 1km, 10km, 40km or even 80km 10G to 40G connection solutions. Let’s talk about the detail information of these solutions.

Spending Less for up to 40km 10G to 40G Connection

You can use the 40GBASE-PLRL4 QSFP+ and 10GBASE-LR SFP+ modules to support the 10G to 40G migration up to 1 km. The 40GBASE-LRL4 QSFP+ is also a good choice. As for the fiber patch cable, you can choose the 8 fibers single mode MTP-LC harness cable. Once the distance is longer than 1 km, your are suggested to use the 40GBASE-LR4 QSFP+ and 40GBASE-PLR4 QSFP+ modules. These two kinds of fiber transceiver modules enable the connection at lengths up to 10 km. It the link distance is up to 40 km, then you can use the 40GBASE-ER4 QSFP+ module. Here are the related equipment offered by FS.COM.

Spending Less for up to 80km 10G to 40G Connection

Have you ever felt puzzled about whether the 10G to 40G connection can be extended to 80 km? Here you’ll find the answer is yes. How to deploy 80km 10G to 40G connection? You should add the extra equipment, including two DWDM Mux Demux, two WDM transponder OEO (Optical-Electrical-Optical) repeaters and several DWDM SFP+ modules, to your network.

In order to make a smooth 80km 10G to 40G migration, we should add the WDM transponder OEO repeater into the 10G to 40G link. It can not only act as fiber repeater for long distance transmission, but also CWDM/DWDM optical wavelength converter. When the 10G signals pass through the WDM transponder OEO repeater, it will be converted into several DWDM singals. Then you should use the DWDM Mux Demux to multiplex, transmit and demultiplex them. And finally another WDM transponder OEO repeater is required to convert the DWDM singals into 10G signals again. Hence, you can finally achieve the up to 80km 10G to 40G connection. As for the equipment the network requires, you can also order them from FS.COM with good prices.

Conclusion

FS.COM is an ideal fiber optical manufacturer that offers very cost effective solutions for 10G to 40G connection. These solution can support not only the short 10G to 40G migration at lengths up to 400 m, but also the long migration with reach 1km, 10km or even up to 40km. Moreover, if you want to extend the 10G to 40G connection up to 80 km, you can order the extra equipment like DWDM Mux Demux, WDM transponder OEO repeaters and DWDM SFP+ modules from FS.COM with good price. All the equipment mentioned above have been tested to assure 100% compatibility.

Original source: http://www.chinacablesbuy.com/economical-solutions-for-10g-to-40g-connection.html

[katherinewangfs-blog]

Can the Hybrid CWDM-DWDM System Work for Higher Capacity?

When facing the capacity-hungry issue, have you ever hesitated over which WDM system should be choose? As the CWDM system is a more economical solution for limited expanding capacity while the expensive DWDM solution enables much higher capacity, which one should be chose is really a tough decision. In order to solve the issue, can we deploy a Hybrid CWDM-DWDM system, for not choosing a wrong solution to increase the network capacity? Thereby, both the bandwidth shortage with CWDM solution or the potential bankruptcy with DWDM solution can be avoided. Let’s seeking the answer.

Can the Hybrid CWDM-DWDM System Work?

Can the Hybrid CWDM-DWDM system work for higher network capacity? The answer is yes. In fact, it is an ideal solution for boosting the network capacity, which is designed with merging DWDM and CWDM traffic seamlessly at the optical layer, taking full use of the WDM technology. In a hybrid CWDM-DWDM system, more channels can be added to deal with the limited capacity and reach in a CWDM system. That’s to say, the hybrid CWDM-DWDM system utilizes the DWDM technology to empower CWDM system, by integrating CWDM and DWDM equipment, which offers true pay-as-you-grow capacity growth and investment protection.

In short, the hybrid CWDM-DWDM system is a simple, plug-and-play option that enables more DWDM channels interleaved with the existing CWDM channels, for transmitting more data signals. It gets the utmost out of CWDM and DWDM technologies in a single system that greatly reduces the cost, simplifies the installation and keeps the system flexibility for bigger network capacity.

How to Build a Hybrid CWDM-DWDM System?

In general, a normal complete optical connection can be simply done by using a length of fiber patch cable to connect two fiber transceivers and then separately inserting the two transceivers into the ports of two switches. While in a hybrid CWDM-DWDM system, both the CWDM Mux Demux and DWDM Mux Demux should be added offering multiple channels to multiplex and demultiplex the signals. Here offers a typical 44 channel hybrid CWDM-DWDM system information for your reference.

From the figure, we can learn that the original CWDM system uses two 8 channel CWDM Mux Demux with wavelengths from 1470 nm to 1610 nm (20nm channel spacing). In order to add more channels for transmitting larger data signals, two pairs of DWDM multi-channel Mux/Demux are deployed separately under the pass band of the existing CWDM filters. In principle, deploying the DWDM multi-channel Mux/Demux in the 1530nm channel can create 25 100 GHz spaced DWDM channels. However, only 19 DWDM channels circled in the following figure are suitable to be added in the hybrid CWDM-DWDM system. It is also the same to the 1550 channel. Hence, this hybrid CWDM-DWDM system totally offers 6 CWDM channels and 38 DWDM channels with less deployment cost but easier installation.

Conclusion

If you come across the capacity-hungry issue and can’t make the decision about which WDM system should be choose for increasing your network capacity, you are highly recommended to deploy a hybrid CWDM-DWDM system. As an economical and future-proofing solution, the hybrid CWDM-DWDM system can completely deal with the issue of bandwidth shortage when building a CWDM system and avoid the potential bankruptcy for a DWDM system. You can just deploy a CWDM system first. Once the capacity the CWDM system offers can’t meet your requirement, you can add DWDM equipment in for more channels to transmit signals. All in all, the hybrid CWDM-DWDM system is an ideal choice that not only costs less for deployment but keeps the flexibility to increase the network capacity.

[katherinewangfs-blog]

Dual-Fiber or Single-Fiber CWDM Mux Demux for Higher Capacity Need?

What would you do if your network capacity can not meet your requirement? Will you put more fibers or update your system? In fact, these two methods are not very recommendable. Why? As your fiber cabling infrastructure is limited for adding fibers and high cost is required for upgrading system, these two methods are unworkable or too expensive. Under this condition, using a pair of CWDM Mux Demux to build a CWDM system with higher capacity is highly recommended. The CWDM Mux Demux is regarded as a key component for a CWDM system, as shown below. It can be simply divided into two types, dual-fiber and single-fiber CWDM Mux Demux. To meet the higher capacity need of your system, this post will mainly introduce the basic knowledge of the dual-fiber and single-fiber CWDM Mux Demux and guide you find a suitable fiber optic Mux Demux for building your CWDM system.

Dual-Fiber CWDM Mux Demux

Dual-Fiber CWDM Mux Demux is a passive device multiplexing and demultiplexing the wavelengths for expanding network capacity, which must work in pairs for bidirectional transmission over dual fiber. It enables up to 18 channels for transmitting and receiving 18 kinds of signals, with the wavelengths from 1270 nm to 1610 nm. The CWDM transceiver inserted into the fiber optic Mux port should have the same wavelength as that of Mux port to finish the signal transmission. For instance, the two reliable 4 channel CWDM Mux Demux showed below use four wavelengths, 1510 nm, 1530 nm, 1550 nm and 1570 nm, their corresponding CWDM transceivers also features the same wavelengths.

When the connection above works, the left 4 channel dual-fiber CWDM Mux Demux uses 1510 nm, 1530 nm, 1550 nm and 1570 nm for transmitting 4 kinds of signals through the first fiber, while the right 4 channel dual-fiber CWDM Mux Demux features 1510 nm, 1530 nm, 1550 nm and 1570 nm for receiving the signals. On the other hand, the transmission from the right to left use the same wavelengths to carry another 4 signals through the second fiber, finally achieving the bidirectional signal transmission.

Single-Fiber CWDM Mux Demux

Single-fiber CWDM Mux Demux should be also used in pairs. One multiplexes the several signals, transmits them through a single fiber together, while another one at the opposite side of the fiber demultiplexes the integrated signals. Considering that the single-fiber CWDM Mux Demux transmitting and receiving the integrated signals through the same fiber, the wavelengths for RX and TX of the same port on the Single-fiber CWDM Mux Demux should be different. Hence, if the 4 channel single-fiber CWDM Mux Demux is used for CWDM system, 8 wavelengths are required, the twice time as that of the dual-fiber one.

The working principle of single-fiber CWDM Mux Demux is more complicated, compared to the dual-fiber one. As shown in the figure above, the transmission from the left to right uses 1470 nm, 1510 nm, 1550 nm and 1590 nm to multiplex the signals, transmit them through the single fiber, and using the same four wavelengths to demultiplex the signals, while the opposite transmission carries signals with 1490 nm, 1530 nm, 1570 nm and 1610 nm over the same fiber. As for the wavelength of the transceiver, it should use the same wavelength as TX of the port on the CWDM Mux Demux. For example, when the port of a single-fiber CWDM Mux Demux has 1470 nm for TX and 1490 nm for RX, then a 1470nm CWDM transceiver should be inserted.

Dual-Fiber vs. Single-Fiber CWDM Mux Demux

We always consider whether an item is worth buying according to its performance and cost. In view of the performance, the single-fiber CWDM Mux Demux can carry signals through only one fiber supporting fast speed transmission and saving the fiber resource, while the dual-fiber one requires two fibers for transmission with a higher reliability. Besides, using single-fiber CWDM Mux Demux can be easier to install. In view of the cost, the single-fiber CWDM Mux Demux is much more expensive than the dual-fiber. And the simplex fiber cable also costs higher than duplex fiber cable. Thereby, the whole cost for building single-fiber CWDM system must be much more higher. Like the two sides of the same coin, both the dual-fiber and single-fiber CWDM Mux Demux have their own advantages and disadvantages. Which one you should choose just depends on your system needs and your budget for building the CWDM system.

Original source: http://www.chinacablesbuy.com/dual-fiber-or-single-fiber-cwdm-mux-demux-for-higher-capacity-need.html