logosweldproducts - Tumblr blog

[logosweldproducts]

Common welding mistakes which you need to avoid

Welding is the process which involves joining different materials together. Unlike soldering and brazing, during welding a good amount of 'melting' of the metals take place while fixing them together. Usually thermoplastics or metals are used in the welding process.

Like any other sphere of work, welding too requires an in-depth understanding of the basics. There are some mistakes which are commonly committed in the welding process. Right from using the wrong voltage, to creating an arc way too longer than is required. Logos Weld Products is one of the leading welding electrode plant supplier in India. With years of experience and expertise, here is a list of mistake which needs to be avoided in the welding process.

Mistake #1 – Making the arc outside the weld joint

Striking is not an easy task, more so in case of beginners, due to which several times it is seen that the arc is striked outside the weld joint. The best way to avoid this situation is to begin from the point you plan on welding. This way not only will you avoid striking in the wrong manner and also bring down the risk of damaging the other parts of your work piece.

Mistake #2 – Using the wrong current for welding

Yet another common mistake, often it is seen that welders use the wrong current in the welding process. You just need to take the type of metal and electrode into consideration, and it becomes easier to decide which current to use (DC/ AC) and the quantity of current to be used. If you are a first-timer, it is recommended that you cut some scraps of the metal and test it with your settings. This way you will get to know which is the right current for that particular metal.

Mistake #3 – Using electrodes which are damaged

It is very important that the welding electrode plant is not damaged in order to get the results you are looking for. A MIG wire with oil/ rust or a moist electrode for stick welding is sure to cause problems. Always keep in mind that the 7018 electrodes which are used in stick welding needs to be kept dry and warm in an electrode oven. In case there is no oven, then all you need to do is heat the 7018 electrodes before using them for welding.

Mistake #4 – Not cleaning the metal correctly

This is one of the most common and perhaps easily avoidable mistakes in the welding process. The quality of welding is affected if the metal is not cleaned in the right manner. Especially in the case of TIG welding, it is crucial that you use the right solvent like acetone. This way the quality of the welding will not be compromised. Other solvents like paint thinners etc too can be used for cleaning the metal.

To get more information on welding electrode making machine you can visit www.logosweld.com or call at +91 422 2934784.

Logos Weld  with their state-of-art welding rod manufacturing plant are the best Welding electrode powder supplier in India. They hold ISO 9001:2008 certification and have been providing quality welding services since 1994.

[logosweldproducts]

Flux-Cored Arc Welding

Welding involves joining different materials together. In the welding process a good amount of 'melting' of the metals takes place while fixing two metals together, and this is what differentiates it from soldering and brazing. Usually metals or thermoplastics are used in the welding process. Flux-cored arc welding (FCAW) is one of the popular welding processes. It is an automatic or semi-automatic arc procedure. Introduced in the 1950s, this process involves the use of a new kind of wire electrode on an MIG welding machine. This is the reason why flux-cored is regarded as similar to MIG welding process. The equipment's used in both the processes are same, so are wire fields and power supply. The wire used in this purpose is the tubular wire and not that the usual solid wire.

Basically there are two types of flux-cored wire:

Self-shielded

Dual Shield

While self-shielded wires do not use any external gas shield, rather they employ the flux to shield the molten weld puddle; dual shield wire uses both the external shielding gas as well as the flux to protect the molten weld puddle. Usually carbon dioxide and argon are used as shielding gases in dual shield flux cored wire.

If we compare flux-cored arc with MIG welding process, then it is has greater productivity. While a MIG welder can produces on an average 5 to 8 pounds of weld in an hour, FCAW produces above 25 pounds of weld per hour. Along with higher productivity, flux-core welding can weld 1/2” plates at a time that too on both the sides with full penetration. This is the precise reason why this welding process is used in the ship building industry which requires high quality welds which are not time consuming and can work even in windy conditions. It is also used in construction industry due to its speed and portability.

Advantages of Flux-cored arc welding

This welding process involves minimal weld clean up.

It requires lower heat inputs.

The electrode efficiency is extremely high.

No external shielding gas is required.

Reduced welding fumes.

Disadvantages of Flux-cored arc welding

It is recommended for heavy material only. Thus cannot be used for thin materials.

Lot of smoke is generated in the whole process.

Produces a lot of slag.

The cost of the equipment is extremely high.

For more information on welding and welding electrode making machine, you can visit www.logosweld.com or call at +91 422 2934784.

Logos Weld  with their state-of-art welding rod manufacturing plant are the best Wire Straightening and Cutting Machines Manufacturer. They hold ISO 9001:2008 certification and have been providing quality welding services since 1994.

[logosweldproducts]

Basics to be known before you start welding

Just like any work of art, welding too requires a thorough knowledge of the basics in order to master its different processes. Here is a simplistic understanding about welding and related topics from Logos Weld Products - one of the leading Welding rod manufacturing plants in India.

To begin with welding is the process through which materials are joined together to form a firm joint. Usually metals or thermoplastics are used in this process. What makes welding different from the other metal joining techniques like brazing and soldering, is the fact that when two metals are joined together in this process, a decent amount of 'melting' of the metals takes place.

Some of the best welding methods are:

Shielded Metal Arc Welding

Gas Metal Arc Welding

Flux-Cored Arc Welding

Submerged Arc Welding

Shielded metal arc welding uses an electrode which has the flux around it. This flux is the protectant for the puddle around the electrode. The electrode holder on the other hand holds the electrode as it melts away in the welding process. The slag on the other hand protects the weld puddle from atmospheric contamination of any kind. Gas Metal Arc Welding on the other hand uses a wire feeding gun. This wire feeding gun feeds the wire at an adjustable speed and flows an inert gas (Argon gas) or a mix of carbon dioxide and Argon over the weld puddle to protect it from atmospheric contamination.

Flux-Cored Arc Welding is quite similar to Gas metal arc welding. The only exception is that this method of welding uses a special tubular wire filled with flux. Depending on the filler, you can either use or not use the tubular wire. While the Submerged Arc Welding makes use of an automatic fed consumable electrode along with a blanket of granular fusible flux. In this method of welding the molten weld and the arc zone are constantly protected from the atmospheric contamination as it is “submerged” under the flux blanket.

These are some of the basic ways in which welding can be done. 

For better understanding about the various kinds of welding and other Logos Weld products visit www.logosweld.com.

Logos Weld with their state-of-art Welding electrode machine exporter are the best Welding electrode flux exporter in India. 

They are ISO 9001:2008 certified and have been providing quality welding services since 1994.

[logosweldproducts]

Different kinds of sieving machines

Sieving is the process through which unwanted elements are removed from the wanted elements. This surely is a very lose way to describe the process of sieving; because many times this technique is also used to separate particles of various shapes and sizes in order to refine the product. Usually a siever has a net or a mesh in order to screen out the unwanted material.

A sieving machine typically consists of two chambers – one in which the waste/ unwanted materials are collected; another which collects the required material. These machines come in various shapes & sizes and are used depending on the industry of work. 

Based on their shape and size sieves can be broadly of three types:

Perforated plate sieves: This type of sieve confirms to the ISO 3310-2 and has a diameter range from 200 to 450 millimeters. The perforated plate sieves have square/ round nominal apertures which ranges from 1 millimeter to 125 millimeters.

American standard sieves: They are also known as ASTM sieves, as they conform to the ASTM E11 standard. Unlike the perforated plate sieve, ASTM sieves are available in only 8 and 12 inch diameter sizes. Their nominal aperuture ranges from 20 micrometers to 200 millimeters.

Woven wire mesh sieves: One of the most commonly used sieves, woven wire mesh sieves conform with the ISO 3310-1. Their nominal aperture ranges from 20 micrometers to 3.55 millimeters, and when it comes to their size – these sieves diameter ranges from 100 to 450 millimeters.

As has already been mentioned, based on the end-requirement, sieves are selected and brought into use. According to Logos Weld –  leading Wire Straightening and Cutting Machines Manufacturer in India – it is important that the size and capacity of the work load should be taken into consideration before investing on any such machines. 

The other important aspects that needs to be paid attention to are:

The construction of the sieve

Most of all, the sieve should be easy to maintain

Its design

The housing should be non-corrosive in nature

Logos Weld also recommend a sieve analysis test before settling on a sieving machine. A sieve analysis is basically a process through which the gradation or the size of the particles to be separated can be assessed. This test can be performed on organic as well as non-organic materials. Usually this process is quite widely used in the area of civil engineering. But those belonging to other industries too can make use of this analysis so that they choose an appropriate siever.

For more information on Flux Sieving Machine Manufacturer and welding rod manufacturing plants you can visit www.logosweld.com or call at +91 422 2934784.

[logosweldproducts]

Logos Weld brings you the Basics of Welding

Just like any work of art, welding too requires a thorough knowledge of the basics in order to master its different processes. Here is a simplistic understanding about welding and related topics from Logos Weld Products - one of the leading suppliers of welding products in India.

To begin with welding is the process through which materials are joined together to form a firm joint. Usually metals or thermoplastics are used in this process. What makes welding different from the other metal joining techniques like brazing and soldering, is the fact that when two metals are joined together in this process, a decent amount of 'melting' of the metals takes place.

Some of the best welding methods are:

Shielded Metal Arc Welding

Gas Metal Arc Welding

Flux-Cored Arc Welding

Submerged Arc Welding

Shielded metal arc welding uses an electrode which has the flux around it. This flux is the protectant for the puddle around the electrode. The electrode holder on the other hand holds the electrode as it melts away in the welding process. The slag on the other hand protects the weld puddle from atmospheric contamination of any kind. Gas Metal Arc Welding on the other hand uses a wire feeding gun. This wire feeding gun feeds the wire at an adjustable speed and flows an inert gas (Argon gas) or a mix of carbon dioxide and Argon over the weld puddle to protect it from atmospheric contamination.

Flux-Cored Arc Welding is quite similar to Gas metal arc welding. The only exception is that this method of welding uses a special tubular wire filled with flux. Depending on the filler, you can either use or not use the tubular wire. While the Submerged Arc Welding makes use of an automatic fed consumable electrode along with a blanket of granular fusible flux. In this method of welding the molten weld and the arc zone are constantly protected from the atmospheric contamination as it is “submerged” under the flux blanket.

These are some of the basic ways in which welding can be done. For better understanding about the various kinds of welding and other Logos Weld products visit www.logosweld.com.

Logos Weld with their state-of-art welding rod manufacturing plant are the best welding products suppliers in India. They are ISO 9001:2008 certified and have been providing quality welding services since 1994.

[logosweldproducts]

Sieving machines and their types

The process of removing unwanted elements from those which are wanted is called sieving. Apart from this the process is also used to separate particles of various shapes and sizes in order to refine the product. In most of the cases a siever has a net to screen out the unwanted material.

Typically a sieving machine consists of two chambers – one which collects the required material, and the other wherein unwanted material is collected. Depending on the industry of work, seiving machines come in various shapes & sizes. Broadly they are of three types:

Perforated plate sieves: It confirms to the ISO 3310-2 and has a diameter range from 200 to 450 millimeters. The appertures in the  perforated plate sieves ranges from 1 millimeter to 125 millimeters and are square/ round in shape.

American standard sieves (ASTM): They conform to the ASTM E11 standard and unlike the perforated plate sieves, are available in only 8 and 12 inch diameter sizes. Their nominal aperture ranges from 20 micrometers to 200 millimeters.

Woven wire mesh sieves: This is the most commonly used sieves. They confirm with the ISO 3310-1 and have a nominal aperture ranges from 20 micrometers to 3.55 millimeters. Their diameter ranges from 100 to 450 millimeters.

Based on the end-requirement, sieves are selected and brought into use. According to Logos Weld –  leading sieve machine manufacturers in India – it is important that the size and capacity of the work load should be taken into consideration before investing on any such machines. The other important aspects that needs to be paid attention to are:

The construction of the sieve Its design The housing should be non-corrosive in nature Most of all, the sieve should be easy to maintain

Logos Weld also recommend a sieve analysis test before settling on a sieving machine. A sieve analysis is basically a process through which the gradation or the size of the particles to be separated can be assessed. This test can be performed on organic as well as non-organic materials. Usually this process is quite widely used in the area of civil engineering. But those belonging to other industries too can make use of this analysis so that they choose an appropriate siever.

Logos Weld is the leading welding electrode flux manufacturer exporter. They have some of the best wire straightening and cutting machines. You can get more information on sieving machines at www.logosweld.com or call at +91 422 2934784.

[logosweldproducts]

TIG welding – How does it work?

TIG in TIG welding stands for Tungsten Inert Gas. It is also known as Gas Tungsten Arc Welding (GTAW) and involves the use of non-consumable tungsten electrode to deliver current to the welding arc. This welding technique was developed in 1930s and was used during the times of secong world war to weld parts of aircraft and is today used in welding stainless steel, chromoly, aluminum, bronze, brass and gold.

How to weld with TIG?

Logosweld is among the top welding electrodes machine suppliers in India. Here is a brief expalnation on how the TIG weld works.

The first step is to clean the welding material. You can use stainless stell wire brush for aluminum, sander for carbon steel while for stainless steel all you need to do is wipe the weld area with a solvent. Once the surface is clean, the next step is to use tungsten electrode. You need to open the back of the electrode holder on the collet. Then insert the tungsten electrode and close the electrode holder. Make it a point that the electrode hangs at least 1/4-inch away from the protective sheath on the collet.

Now use a C-clamps to secure the parts you wish to weld together. You can also make use of  tack welds to hold the parts in place, until the final welding has taken place. The next step is to hold the TIG torch at about 75 degree angle, with the tunsgten raised up to 1/4 inch off the metal. It is important that the tungsten does not touch the work piece, or else it will contaminate the material.

With the torch heatup the base metal and advance the puddle in the desired direction using your arc. Continue to advance the puddle until the whole of the desired area has been welded.

And with this your TIG welding has been completed.

To get more information on welding and related services, visit www.logosweld.com. You can also call at +91 422 2934784 and get a detailed understanding of their services.

LogosWeld is the top welding electrode plant and machineries exporter. They have the best welding electrode manufacturing plant which is in-sync with the latest technology.

[logosweldproducts]

Various powders used in welding electrode

One of the major raw materials used in the electrode welding process are powdered form of metals, minerals and ferro alloys.  With higher productivity, improved quality of weld products and  demand for better welding characteristics, most welders have starting using metal powders as an important component in cored wired as well as for coating the welding electrodes.

Nickel powder, iron powder, tin powder, tungsten powder are some of the most commonly used metal powders in the welding rod manufacturing plant. Among all these powders, the use of iron powder shows great results in improving the quality of the products. Even the efficiency of the electrode improves as slag is removed, spatter level comes down and the re-striking feature is quite better.

Iron powder can be used in various industries – right from welding, brazing, metallurgy, iron fortification, dyes & stains, treatment of iron chlorosis to the making of sintered products, soft magnetic products, friction products, breaks & clutches, filtration and metallurgy. Generally the high quality fine iron powder is used in the manufacture of soft magnetic components, printing, surface coating, polymer filterations and in soft magnetic components.

Here are some varieties of iron powder:

Iron325

This variety is used specifically in the manufacture of low to medium density P/M applications, resin casting, printing inks and smooth magnetic paints. It is super fine and high in green strength.

Iron100

Used mainly in rough magnetic paints and resin casting. It is a high green strength reduced iron powder.

S100

Used in fire works, electro magnetism as iron fillings, chemical reactions for the production of iron chloride, iron sulfide etc and in concrete to increase weight.

S1001

A highly compressible, water-atomized steel powder, S1001 is specifically designed for providing high density and strength in powder metallurgy and forging applications. Along with this it is also used in the production of metal clays, magnetic paints, resin casting and brazing pastes.

SM1001

This is a high purity soft iron powder used in making of soft magnetic components using resin casting method. It is highly compressible, water-atomized powder specifically meant for high density and high strength soft magnetic P/M components.

IRON12

A coarse spongy iron powder made of high purity iron ore, it is used in chemical applications as well as in friction and filtration applications as well.

Depending on the industry and application requirements, any of these welding electrode powders can be used.

For more information on welding and welding powders, visit www.logosweld.com or call at +91 422 2934784.

[logosweldproducts]

Different kinds of sieving machines

Sieving is the process through which unwanted elements are removed from the wanted elements. This surely is a very lose way to describe the process of sieving; because many times this technique is also used to separate particles of various shapes and sizes in order to refine the product. Usually a siever has a net or a mesh in order to screen out the unwanted material.A sieving machine typically consists of two chambers – one in which the waste/ unwanted materials are collected; another which collects the required material. These machines come in various shapes & sizes and are used depending on the industry of work. Based on their shape and size sieves can be broadly of three types:

Perforated plate sieves: This type of sieve confirms to the ISO 3310-2 and has a diameter range from 200 to 450 millimeters. The perforated plate sieves have square/ round nominal apertures which ranges from 1 millimeter to 125 millimeters.

American standard sieves: They are also known as ASTM sieves, as they conform to the ASTM E11 standard. Unlike the perforated plate sieve, ASTM sieves are available in only 8 and 12 inch diameter sizes. Their nominal aperuture ranges from 20 micrometers to 200 millimeters.

Woven wire mesh sieves: One of the most commonly used sieves, woven wire mesh sieves conform with the ISO 3310-1. Their nominal aperture ranges from 20 micrometers to 3.55 millimeters, and when it comes to their size – these sieves diameter ranges from 100 to 450 millimeters.

As has already been mentioned, based on the end-requirement, sieves are selected and brought into use. According to Logos Weld – leading sieve machine manufacturers in India and Flux Sieving Machine Manufacturer -it is important that the size and capacity of the work load should be taken into consideration before investing on any such machines. The other important aspects that needs to be paid attention to are:

The construction of the sieve

Its design

The housing should be non-corrosive in nature

Most of all, the sieve should be easy to maintain

Logos Weld also recommend a sieve analysis test before settling on a sieving machine. A sieve analysis is basically a process through which thegradation or the size of the particles to be separated can be assessed. This test can be performed on organic as well as non-organic materials. Usually this process is quite widely used in the area of civil engineering. But those belonging to other industries too can make use of this analysis so that they choose an appropriate siever.For more information on sieving machines you can visit www.logosweld.com or call at +91 422 2934784.

[logosweldproducts]

Sieving Machines – An Introduction

Sieving is the process through which unwanted elements are removed from the wanted elements. This surely is a very lose way to describe the process of sieving; because many times this technique is also used to separate particles of various shapes and sizes in order to refine the product. Usually a siever has a net or a mesh in order to screen out the unwanted material.

A sieving machine typically consists of two chambers – one in which the waste/ unwanted materials are collected; another which collects the required material. These machines come in various shapes & sizes and are used depending on the industry of work. Based on their shape and size sieves can be broadly of three types:

Perforated plate sieves: This type of sieve confirms to the ISO 3310-2 and has a diameter range from 200 to 450 millimeters. The perforated plate sieves have square/ round nominal apertures which ranges from 1 millimeter to 125 millimeters.

American standard sieves: They are also known as ASTM sieves, as they conform to the ASTM E11 standard. Unlike the perforated plate sieve, ASTM sieves are available in only 8 and 12 inch diameter sizes. Their nominal aperuture ranges from 20 micrometers to 200 millimeters.

Woven wire mesh sieves: One of the most commonly used sieves, woven wire mesh sieves conform with the ISO 3310-1. Their nominal aperture ranges from 20 micrometers to 3.55 millimeters, and when it comes to their size – these sieves diameter ranges from 100 to 450 millimeters.

As has already been mentioned, based on the end-requirement, sieves are selected and brought into use. According to Logos Weld –  leading sieve machine manufacturers in India – it is important that the size and capacity of the work load should be taken into consideration before investing on any such machines. The other important aspects that needs to be paid attention to are:

The construction of the sieve

Its design

The housing should be non-corrosive in nature

Most of all, the sieve should be easy to maintain

Logos Weld also recommend a sieve analysis test before settling on a sieving machine. A sieve analysis is basically a process through which the

gradation or the size of the particles to be separated can be assessed. This test can be performed on organic as well as non-organic materials. Usually this process is quite widely used in the area of civil engineering. But those belonging to other industries too can make use of this analysis so that they choose an appropriate siever.

For more information on sieving machines you can visit www.logosweld.com or call at +91422 2934784.

[logosweldproducts]

High Speed Wire Straightening & Cutting Machines in India

Welding is a sculptural process where two materials are joined up with with the help of tremendous temperature. The best way to weld is by obtaining a welding electrode machine. Welding is used in most of the commercial based industries. The producers prefer this machine a lot.

They are the types to play one of the most important parts in manufacturing a material product. Not only for making a item but also for the facilities this machine is extremely used. This product can be very helpful in terms of making the most significant work in a making industry at a perspective of hand. The welding machines are also applied not only for joining materials but also for splitting them in different ways.

Welding electrodes

Welding production plants are the ones to make the welding electrodes in a sensible way. Some of the service suppliers in this aspect have been creating the best products in the market from the Welding Electrode Machine Manufacturers in India.

They offer you with the best in the industry as they are the ones to make the most useful products in this industry. Thus if you are searching for the electrodes for the industrial use, it is best to get through some of the online websites to select the best service.

Wire straightening service

The wire straightening devices are the ones which are commonly by the wire manufacturers. Some of the organizations are also prudent in making cutting machines. This company has come online for a better marketing and support for the customers these days.

The Wire Straightening And Cutting Machine is highly preferred by the industries as the machines help in saving the manpower. The technological innovation has made a high effect in the manufacturing sectors these days. Without these machines the circulation of work will not be up to the mark.

Some of the businesses procure best welding equipment all over and they are the ones to make the most appealing services all over India. The Welding Electrodes Machinery and Equipment are the one to make the most appealing services all over. You can get reductions and different offers and deals for the best price.

If you are getting machinery for manufacturing reason then you will have to buy them in bulks from the market. For that you cannot manage cramp tools and thus for the bulk machinery you will have to make the smartest decision and opt for the best in the market.

The best for the company

These days the Welding Electrode Manufacturing Plant is easily accessible online now and there but the best way to buy them is by knowing about the company in a specific way and then examining about the item. If you are opting for this brand name then you can get a specific information of the product and their services.

You can also get the guarantee for the full fulfillment from the products. The after sales service is also a prudent one. Some of the companies has the ability meet up with the clients expectation whenever they are needed. So go for the best and have a safe welding experience. Read More : http://www.logosweld.com/products.html

[logosweldproducts]

Welding Safety Tips and Guidelines

Welding is one of the most dangerous and thrilling professions in the world. Welding is actually heating one metal over the other so that they both melt and dry up to join together. Welding machines are embedded with welding electrodes. Welding Electrode Making Machines coat straightened wire with flux which is then dried to form the electrode responsible for melting and joining two metals.

Here are a few fun facts about welding that you just didn’t knew before:

1. Welding is one of those professions that needs no educational qualification and interestingly has been called as “Best kept secret” professions as it can never be taught instead; skills have to be developed on your own.

2. Welding is something that has been practiced continually for centuries in countries like India. It can be traced back to the Egyptian era as their tombs have images of welders as well the iron tomb in Delhi, India that dates back to 300 AD, which marks the presence of Welding Electrode Machine Manufacturers in India for long.

3. There are many ways to weld, unlike what has been assumed by most of us. You can arc weld, metal weld, glass weld and more of its types.

4. Welding can be done with different energy sources including mostly of those that are used to heat food like glass flames, electric arc, laser rays, ultrasound rays and others.

5. Welding is not only limited to earth and metals. It has been tried and experimented in areas like underwater and space. However the risk involved is increased many folds. Many people have to sacrifice their lives if proper instructions are not followed while performing underwater welding.

6. Welding without noise: Yes it’s possible. Welding in outer space or any vacuumed environment is silent, only sparks can be seen coming out.

7. Not only that metals are welded, there are other elements as well that can be welded. These elements include plastic and Lead glass tubes.

8. Welding is also amongst those professions that are performed not only by humans, but also robots. Robot welders can be seen welding in industries.

9. More than 50% of man-made items require welding. For instance, the roads, the cars, aircrafts, laptops and almost everything that you can think of and sometime don’t think of.

10. Average welders age on this point of time is 50+, precisely said 54. That means after 10 years there is going to be high demand of welders with qualities and hence high scope.

11. Welding Electrode Making Machines are an important element for this profession as the strength and tensile strength of their output i.e. welding electrodes is responsible for make or breaks of any building, bridge etc. most of the time.

So these are few fun and interesting facts about welding that you can use to wow others and impress them with subject knowledge of a profession that has no alternatives on Wire Straightening and Cutting Machines Manufacturer, low competition and very high demand and bright scope in future. Read More about Welding tips : http://www.logosweld.com/welding-products.html

[logosweldproducts]

Technical aspects:  Manufacturing Welding Electrode Plant and Machinery

Welding electrodes, as the name suggests are equipments that are used for arc welding purpose. These electrodes are coated with flux. So, basically to understand the concept of Welding electrodes, we must know what is Welding? The process of joining a metal to another metal is known as Welding. If said in simple words, it’s like heating two metals at a very high temperature so that both of them melt and get stick to each other and thus joined strongly enough so that they can’t be easily disjoined. This is an important process that has found wide applications in constructions, building, airplanes, cars, bridges and anything where ever you find metals joined.

Welding electrodes are produced to be used for fabrication of joining

1. Steels

2. Alloy Steel

3. Cast Iron

4. Hard iron etc.

The process of Welding Electrodes Machine Manufacturers India:

Though this process was earlier used only for big projects and large scale applications, however it has gained space even in small scale applications. How welding Electrode Making Machines work and what do they produce. Let’s know more about it.

1. First of all, Electrode quality wire of desired size is straightened on any straightening machine. The size of this wire may vary.

2. Then this wire is being cut and stored.

3. The flux for this wire is then made, as per the formulation devised or depending upon the requirements of Welding electrode. This flux is prepared in dry blender and a wet mixer.

4. Then comes the automatic slug press, in which a slug is prepared in cylindrical shape.

5. This slug is then placed on extrusion press and straight cut wires are fed in wire feeder.

6. Flux coated on wires is passed on conveyor for fixing it and then collected at end.

These flux coated roads are then dried in oven. Once dried it is packed well and sent for manufacturing. Before being manufactured these Welding Electrode Plant and Machineries Exporter tests these electrodes for

1. Tensile strength for pressure handling

2. Hardness

3. Compression strength

4. Chemical compositions

5. Bending and more

There is no alternative of making welding electrodes and thus, this process has impeccable scope. Welding Electrodes Machine Manufacturers India have devised several innovative welding electrode manufacturing machineries. These machineries are imported as well exported and are indigenously available. There lies great scope in this field.

[logosweldproducts]

Some Facts to Know About the Welding Electrode Plant Suppliers

Welding is a well known and established method of joining metals on permanent basis. Facts related to the process are still on the way to growth. The day by day increasing demand of welding equipments and machineries represent the actual requirement of welding in the industrial world. The most important thing to know about the process of welding is that it reduces the cost of fabrication in metal industry. The current data about growth and development of manufacturing units dealing with the production of welding equipments and machineries shows that this will attain hike rapidly in near future.

Nowadays, the welding process has become technical advance with updated equipments featured semi-automated and even fully automated functioning. Earlier when industrialists were employing manual Welding rod manufacturing plants in their service units, the process was time consuming and lesser perfect. With the gradual updates and advancement in machineries being utilized in the welding process, things have been changed positively and a stage occurred when the Indian welding services become one of the best known services all around the world.

The success of advance welding services all around the world can be denoted easily through growing shipbuilding and energy sector, wind power sector and engineering industry. According to an analysis by leading researchers, the field of welding will never face recession as every industry requires efficient performance for joining metals together for one or another reason. Definitely, the progress of welding electrode machine suppliers from manual to automatic level has become a key to growth for various technical sectors.

Due to the mind-blowing performance and robust designing of welding electrode plants in India, many leading foreign automobile companies prefer setting up their industrial units in India. This is how; the country enjoys positive impact upon the demand of welding equipment. Still, a little hike in the rate of import of welding equipments affected the local market of these machines negatively in India during recent years. To beat this situation also, the country based welding service specialists strive hard to modify their equipments for advance functioning. They concentrate a lot in contribution of advance features while designing the products too. So now, positive point to be noticed is that the Indian welding machinery sector is successful in securing it’s significant place on global market.

Customers love to know that they Indian market of welding equipments is not only flourishing well but also pays much emphasis on customer friendly services. This is why, all the equipments offered by them come with guarantee and warranty services as well as available at affordable price. Moreover, they have simplified the process of ordering these equipments so that you can simply place your order online only. Alternatively, you can talk to the customer care staff telephonically or through E-mail for further information.

[logosweldproducts]

Know More about the Welding Electrode Plant and Machinery Exporters in India

Finding the best welding plant and machinery exporter in the world is not a tough task nowadays because a well established web world in available now representing the best service providers in this series. When it comes upon the list of renowned and well settled welding exporters in India, many good service dealers are there to offer their awesome services to those who are looking for good quality designing and better functioning. The best thing to know about leading service dealers is that they have been established several years ago. This has made them perfect to meet demand of technological units all around the world.

Due to the classy performance and unbeatable designing of products has made the Indian electrode and machinery exporters well known on international level. This has made them globally recognized technical leader who are good not only for offering even bulk orders on time but also to upgrade the quality of their products time to time.  As the Indian Welding Electrode Plant and Machineries Exporter are based upon the foundation of trustworthy services, their customers never find any chance of disappointment while enjoying their services. Whether you talk about the proven reliability of their machines or about their state-of-the-art technology, they are awesome to meet demand of their customers on every aspect.

According to the Indian welding electrode plant and machinery suppliers, the robust designing, good installation and excellent maintenance services they offer impress their clients. These valuable services make people fall for their services and enjoy their assistance whenever they want to order affordable welding plants.  Another important thing to know in this direction is that the country based service providers are dedicated to customize their services as per demand of their clients. Offering a wide array of Welding rod manufacturing plants, they have achieved the standard on which they present hassle free performance to their customers. This is why; people love to set up long term professional relationship with the Indian service dealers.

Last but not the least to say here is that the Welding electrode machine exporter in India is that the products supplied by them are accessible in various specifications according to the demand of customers. All the electrode machines they offer are available at affordable price. Actually, the reputed service dealers of India in this direction hire only skilled employees and design sound infrastructure for this purpose; this is how, they find it simple to maintain good quality deals at reasonable cost for all domestic and foreign customers, both.

You might have been looking for the way now to contact the leading electrode machinery suppliers online. Well, you need nothing but to visit their official website in internet and fill a service request form online. Just by submitting that service request form, you can pave your way to the world class services as their customer care staff contacts to you as soon as they find your service request.  

INFRASTRUCTURE

Logos boast of sound infrastructure and highly skilled and dedicated work force that enable us to serve to customer's requirement. The R&D department is equipped with the latest computer added design (CAD) section and material testing lab. Production involves stringent quality checks resulting in flawless products.

Research and Development - R & D

Being a progressive organization run by a team of highly experience and well trained techno crafts we look forward innovative ideas. We are constantly designing and fabricating new products as per the requirements of the customers.

SERVICE

Logos service department recognizes the needs of occasional adjustment are repair of equipments after they have been sold to the customers. Over the years we have been fulfilling our commitment of providing your quick and prompt service for all the products supplied by us.

Ref : If you need Welding Electrode Plant and Machineries Exporter in india contact us : http://www.logosweld.com

[logosweldproducts]

Technical Know How for Welding Electrode Manufacturing

The manufacturing industries now a day have adopted many ways to reduce the manpower and monthly charges.  Technology has opened the door for them as they are the one to make the work easy by introducing new machines or products in the market. Though welding is an old concept of joining metal pieces by applying immense heat to it but in the recent times this idea has taken a step forward by making the welding electrode machines.  They are the ones to make the most of market in the manufacturing industry these days. This Welding Electrode Machinery has made the work of welding easier then ever before. The industries are investing a lot on these machines as this machine has become a must be tool for their regular work.

The pro level machines

For the industrial use the welding electrode machines are highly preferred as they are the ones to make the most promising services. Before buying a welding electrode manufacturing machinery for your home based jobs or industrial works, you can get the details of some of the companies from the Internet. They are into the web to get reach of many other customers which is impossible without the help of internet. A few among them are the one to make the most promising services all over. The welding electrodes are the ones in this field which is technologically very much advanced and in terms of products no one needs a second look to it. They are the one to make the most promising services in the industry. They are in this business for many years.

Some of the companies are making the best welding electrode products in the market. They will offer you with the best in the market as they are the ones to make the most valuable products in this industry. Some are specialized in making wire straightening machines. welding electrode plant supplier is used not only for making a product but also for the infrastructure, this machine is highly used. This product can be very useful in terms of making the most important work in a manufacturing industry with just a flick of hand. This machine has the ability to make the work easier. This is just a one-time investment scheme where you are investing on the Welding Electrode Making Machines for once and then it is going to save your man power and the other expenses for the work. Some of the companies have a wide range of welding products for the industrial use. Among all the other industrial welding machinery brands, choose the company that is highly preferred by the mass.

The market’s acclaimed

If you are planning to buy a welding electrode machine then at first you will have to look for the best in the market and then you will have to search them online for their authentication. The website present online as well as offline in the markets is to be checked hence forth. Some also provides the best after sales service in the market and also looks after your satisfaction in a prudent way. Choose the company that is a veteran in meeting up with the customer needs. So go for the best for your industrial purposes.

[logosweldproducts]

How welding rod manufacturing machineries Manufacturing

There are three important things that you will get in the manufacturing unit of the machines. The machine is for the straightening of the wires and for the generation of the electrode plates and machineries. All the heavy machineries are to be required in the industries and that is the most important support that you will need in this aspect. You can get to some of the sites and check the most popular companies out from there. Some of the important things that you must check out there are as follows:

Different service support

The different system support that you can expect is going to provide the best support for the company of yours. You will find that very few of the companies who are Welding Electrodes Machine Manufacturers India provide an online support. Some of them do really provide a support where you can get the support of online booking of the machineries even. Thus it is better to get there to the site and thus generate the best revenue for your company.

Essential features of support

There are certain supportive features that you will have to follow in the proceedings. Choose the right support of the machineries from the list of the products. The most important part in them is to get a quotation for the service. You can get the online support of the quotation from some of the sites, and there from you can get the different issue related support too. The issue related support for the Welding Electrode Manufacturing Plant is not going to solve the purposed of your company, but you must be looking to get the support of the best one in term of the budget and timely delivery. Thus look out for them in the service that is provided. You will get the details of the service form the list and availing them you can get the best service provider.

Three additional features to be considered

There are three more things that you will have to check in the service. The first of them is the support of the budget. The budget sensibility is the first and the most important thing that you will need in this aspect and thus you can assure to get the service from the most reliable Welding Electrodes Plant Machine Manufacturers India to assure the best results. The second thing is the guarantee attached with the product. You can check the mass scale manufacturers from the site and that will be the most significant thing that you will need in the context of your company. There is one last thing that you will need in this aspect and that is the access of the quick delivery. This option is available from the manufacturing company only. Thus check the sites and see that whether the service is provided by the manufacturer alone. You can determine the best service there on as the bets rate of the products is also available from there. For any additional support, you can visit the best support online.