networksavage

[networksavage]

VIDEO 33 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j This video is about the link layer discovery protocol (LLDP). In this video we are going to go over the LLDP cisco configuration commands. The command to enable lldp is lldp enable. Let's also compare lldp vs CDP. LLDP is the open standard version and CDP is the Cisco proprietary version of the protocol. The lldp configuration and commands are very simple. LLDP is supported on all Cisco routers and switches in case you need to integrate with third party devices. LLDP over poe does work. The lldp run cisco command is what turns the protocol on. By the end of this video you will know all the cisco link layer discovery protocol commands. COMMANDS: lldp holdtime X lldp reinit X lldp timer X lldp run (global) lldp enable (interface) VERIFY: sh lldp nei sh lldp traffic sh lldp errors sh lldp entry by Network Savage

[networksavage]

VIDEO 32 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video we will go through the cisco discovery protocol and the cisco cdp commands. Cisco cdp clients use the cisco cdp enable command in order to enable the cisco cdp discovery tool. There are a few cisco discoveryprotocol commands. The cisco discovery protocol control protocol is used to discover directly connected neighboring devices. There are common errors like cisco discovery protocol is not available on this physical adapter. This is due to the difference between cdp vls lldp. CDP is the cisco proprietary solution while LLDP is the open standard version. CDP does work with some windows clients like Cisco Jabber. COMMANDS: cdp run (global) cdp enable (interface) VERIFY: sh cdp nei (shows all cdp neighbors) sh cdp entry (to look at a specific neighbor sh cdp interface (shows interfaces with CDP running) sh cdp traffic by Network Savage

[networksavage]

GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Where to download GNS3 and VM: https://ift.tt/h1o7BKt Where to download VM Workstation Pro: https://ift.tt/BIpHzWa Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j The purpose of this video is to install gns3 2.2 on ESXi and get it up and running. This video will show step by step how to install gns3 on ESXi. Installing gns3 on ESXi is a fairly straightforward process. It will include gns3 installation and configuration on windows 10. I'll go through the gns3 setup wizard and show what options to pick. This installation will detail how to install gns3 with vm. Installing gns3 with vmware and vm workstation pro is now considered to be the best way to install gns3 and will also have instructions to install the gns3 appliance. I'll show you the best gns3 setup for the ccna. This guide details how to install gns3 step by step and install cisco images. This includes directions to install gns3 dynamips images as well as how to install router and switch images on gns3. This also shows directions on how to install the gns3 client and server with vm workstation pro. by Network Savage

[networksavage]

VIDEO 8 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Windows GNS3 Requirements: https://ift.tt/M3xUZho Where to download GNS3 and VM: https://ift.tt/CFWOiR0 Where to download VM Workstation Pro: https://ift.tt/IoerSG0 Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j The purpose of this video is to install gns3 2.2 on Windows 10 and get it up and running. This video will show step by step how to install gns3 on windows 10. Installing gns3 on windows 10 is a fairly straightforward process. It will include gns3 installation and configuration on windows 10. I'll go through the gns3 setup wizard and show what options to pick. This installation will detail how to install gns3 with vm. Installing gns3 with vmware and vm workstation pro is now considered to be the best way to install gns3 and will also have instructions to install the gns3 appliance. I'll show you the best gns3 setup for the ccna. This guide details how to install gns3 step by step and install cisco images. This includes directions to install gns3 dynamips images as well as how to install router and switch images on gns3. This also shows directions on how to install the gns3 client and server with vm workstation pro. by Network Savage

[networksavage]

Be sure to subscribe and check out the rest of the series for the rest of the labs! Where to download VM Workstation Pro: https://ift.tt/N4flZXPwI Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j The purpose of this video is to show you how to install VMWare's VM Workstation Pro on Windows 10 in the year 2022. by Network Savage

[networksavage]

VIDEO 30 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video I am going to first explain the multiple spanning-tree protocol (MSTP) and then go through mstp cisco configuration examples. The Multiple Spanning-tree cisco configuration examples will be performed in a MSTP GNS3 lab. COMMANDS: SW2-7: sp mo m sp ms c i 1 vl 10,20 i 2 vl 30,40 sp ms i 1 pri 61440 sp ms i 2 pri 61440 SW1: sp mo m sp ms c i 1 vl 10,20 i 2 vl 30,40 sp ms i 1 pri 0 sp ms i 2 pri 4096 SW8: sp mo m sp ms c i 1 vl 10,20 i 2 vl 30,40 sp ms i 1 pri 4096 sp ms i 2 pri 0 VERIFY: sh sp s sh sp vl 10 sh run | i span by Network Savage

[networksavage]

VIDEO 29 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video I am going to go through the Rapid Per-VLAN Spanning Tree protocol (RPVST+) and then show some configuration examples in the lab. COMMANDS: TEMPLATE CONFIG: SW1-8: conf t vlan 10,20,30 int ra gi 0/0 - 2 sw t e d sw m t sw t a v 10,20,30 SW1-8: hostn SWX SW2-7: sp mo p sp e s sp vl 10,20,30 pri 61440 SW1: sp mo p sp vl 10,20 pri 0 sp vl 30 pri 4096 SW8: sp mo p sp vl 10,20 pri 4096 sp vl 30 pri 0 VERIFY: sh sp s sh sp vl 10 sh run | i span by Network Savage

[networksavage]

VIDEO 28 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j This video compares PVST vs PVST+ and goes through the PVST cisco configuration commands. The PVST configuration commands on GNS3 are fairly simple. I will explain how PVST and PVST+ work and what the port roles are. The PVST and PVST+ protocol are almost exactly the same with only one true difference. PVST and PVST+ also differ from Rapid PVST. I will explain this difference as well. COMMANDS: SW2-7: sp mo m sp ms c i 1 vl 10,20 i 2 vl 30,40 sp ms i 1 pri 61440 sp ms i 2 pri 61440 SW1: sp mo m sp ms c i 1 vl 10,20 i 2 vl 30,40 sp ms i 1 pri 0 sp ms i 2 pri 4096 SW8: sp mo m sp ms c i 1 vl 10,20 i 2 vl 30,40 sp ms i 1 pri 4096 sp ms i 2 pri 0 VERIFY: sh sp s sh sp vl 10 sh run | i span by Network Savage

[networksavage]

VIDEO 27 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j This video explains the difference between the different types of Spanning-Tree (STP). We will compare and contrast the following STP Protocols: PVST, PVST+, CST, RSTP, MSTP, and Rapid PVST+. by Network Savage

[networksavage]

VIDEO 26 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j This spanning tree protocol is explained in this video. I go through the spanning tree protocol basics. This is what you need to know about the spanning tree protocol for the ccna certification. The spanning tree protocol algorithm elects a spanning tree protocol root bridge. Spanning tree protocol has advantages and disadvantages. There are a couple commands you can use for spanning tree protocol troubleshooting. This spanning tree protocol video also references spanning tree protocol rfc. The spanning tree protocol steps goes through states as it operates on switches. by Network Savage

[networksavage]

VIDEO 25 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video we are gong to talk about cisco native vlan configuration. I'll show the cisco native commands and options for config. There are a few ways to do cisco trunk native vlan configuration. Big problems occur when there is a cisco native vlan mismatch. When this happens you will see cisco native vlan mismatch discovered or cisco native vlan mismatch detected on interface errors. There is also the concept of cisco native vlan tagging and there is no such thing as cisco native vlan on routers except if you are working with switching modules. What is a cisco native vlan? We'll go through what they are and what they are used for on trunks. I'll show you examples of the cisco trunk native vlan example on GNS3. There will be a cisco native vlan configuration example and we'll explain the cisco native vlan meaning. As well as how to see the cisco native vlan usage, what the native vlan is. I'll go through the native vlan command for cisco. The native vlan concept is thoroughly explained with an explanation. I'll also go through the cisco native vlan configuration example on gns3. PRE-CONFIG:==================== SW1:====================== conf t hostname SW1 vlan 10 name ACCESS vlan 20 name DATA exi int vl 10 ip add 10.0.0.253 255.255.255.0 sh SW2:====================== conf t hostname SW2 vlan 10 name ACCESS vlan 20 name DATA exi int vl 10 ip add 10.0.0.254 255.255.255.0 sh MIN-CONFIG-ACCESS:======== int ra gi 0/0 - 1 switchport mode access switchport access vlan 10 int ra gi 0/0 - 1 switchport mode access switchport access vlan 20 PC1:====================== ip 10.0.0.1 255.255.255.0 10.0.0.253 PC2:====================== ip 10.0.0.2 255.255.255.0 10.0.0.253 PC3:====================== ip 10.0.0.3 255.255.255.0 10.0.0.254 PC4:====================== ip 10.0.0.4 255.255.255.0 10.0.0.254 DEFAULT-INTERFACE:======== default int ra gi 0/2 - 3 NEW-CONFIG:===================== TRUNK-CONFIG:============= SW1:====================== int ra gi 0/2 - 3 switchport trunk encap dot1q switchport mode trunk switchport trunk allowed vlan all switchport trunk native vlan 10 SW2:====================== int ra gi 0/2 - 3 switchport trunk encap dot1q switchport mode trunk switchport trunk allowed vlan all switchport trunk native vlan 20 do sh int tru VERIFY:=================== show vlan brief do show interface trunk do show spanning-tree summary ping 10.0.0.1 ping 10.0.0.2 by Network Savage

[networksavage]

Here is a link to the beginning of this course and playlist for Linux for Network Engineers: https://www.youtube.com/playlist?list=PLhHT1w6sU7CMj-NKi-wQrC0DM0WadS4Bq This is a great way to learn how to use the vim text editor. If you need to learn how to use the vim text editor this is a great tool: https://www.openvim.com You can use it to become proficient with the vim text editor on linux. It's a great place for the beginners to learn the vim text editor. by Network Savage

[networksavage]

VIDEO 24 in the GNS3 Labs for CCNA 200-301 Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video we will go through how to perform cisco trunk port configuration. This will involve what vlans are allowed on the cisco trunk vlan configuration and briefly distinguish the difference between cisco trunk vs access mode. Cisco trunk configuration commands are included. Cisco trunk stetup involves specifying the allowed vlans. I'll include cisco trunk port configuration samples and examples. There are cisco trunk port configuration best practices for cisco switch port trunk configuration. This involves vlan pruning on cisco trunks and we will discuss the cisco trunk encapsulation methods including dot1q. We will also look at the trunk port definition and do a trunk port configuration in a cisco switch. PRE-CONFIG:==================== SW1:====================== conf t hostname SW1 vlan 10 name ACCESS exi int vl 10 ip add 10.0.0.253 255.255.255.0 sh SW2:====================== conf t hostname SW2 vlan 10 name ACCESS exi int vl 10 ip add 10.0.0.254 255.255.255.0 sh MIN-CONFIG-ACCESS:======== int ra gi 0/0 - 1 switchport mode access switchport access vlan 10 PC1:====================== ip 10.0.0.1 255.255.255.0 10.0.0.253 PC2:====================== ip 10.0.0.2 255.255.255.0 10.0.0.253 PC3:====================== ip 10.0.0.3 255.255.255.0 10.0.0.254 PC4:====================== ip 10.0.0.4 255.255.255.0 10.0.0.254 DEFAULT-INTERFACE:======== default int ra gi 0/2 - 3 NEW-CONFIG:===================== TRUNK-CONFIG:============= int ra gi 0/2 - 3 switchport trunk encap dot1q switchport mode trunk switchport trunk allowed vlan 10 spanning-tree portfast trunk do sh int tru int ra gi 0/2 - 3 shut switchport trunk allowed vlan all no shut do sh int tru #ISL int ra gi 0/2 - 3 switchport trunk encap isl switchport mode trunk switchport trunk allowed vlan 10 no sh int ra gi 0/2 - 3 no sh VERIFY:=================== show vlan brief do show interface trunk ping 10.0.0.1 ping 10.0.0.2 by Network Savage

[networksavage]

How to install VIM Text Editor on Ubuntu Linux: https://youtu.be/CvTfCOYI-GQ Here is a link to the beginning of this course and playlist for Linux for Network Engineers: https://www.youtube.com/playlist?list=PLhHT1w6sU7CMj-NKi-wQrC0DM0WadS4Bq We are going to go over the vim shortcuts cheat sheet. There are a lot of VIM editor shortcuts on linux. This video is going to show a lot of vim commands in Linux. I'll also show you how to enter vim command mode. VIM command mode is what allows you to enter commands and I will like to the VIM command reference that shows you a: https://ift.tt/2lcbLW7 Here are the This will include the vim command to save and exit. VIMdiff Cheatsheet: Navigations: ]c Next difference [c Previous difference Editing: do Diff Obtain! Pull the changes to the current file. dp Diff Put! Push the changes to the other file. :diffupdate Re-scan the files for differences. ZQ Quit without checking changes Folds: zo / zO Open zc / zC Close za / zA Toggle zv Open folds for this line zM Close all zR Open all zm Fold more (foldlevel += 1) zr Fold less (foldlevel -= 1) zx Update folds by Network Savage

[networksavage]

VIDEO 23 in the GNS3 Labs for CCNA 200-301 Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video we are going to go through the different ways to perform cisco access port configuration. There are slight differences between cisco access ports vs trunk ports. The cisco switchport mode access command is the first step in configuring an access port. There are also questions about cisco multi vlan access port in configuration. I'll show you how to configure an access port on a cisco switch and describe what a cisco access port is. What happens if you connect a cisco access port to a trunk port. The configuration invloves specifying what vlans you want on the access port. We will also talk about tagged vs untagged vlans as well as using the native vlan on access ports. Access port networking will be easy upon completion of this video. SW1:====================== conf t hostname SW1 vlan 10 name ACCESS exi SW2:====================== conf t hostname SW2 vlan 10 name ACCESS exi MIN-CONFIG-ACCESS:======== int gi 0/0 switchport mode access switchport access vlan 10 int gi 0/1 switchport mode access switchport access vlan 10 IP-PHONE-CONFIG:========== int gi 1/0 switchport mode access switchport access vlan 10 switchport voice vlan 20 spanning-tree portfast SW1:====================== int vl 10 ip add 10.0.0.253 255.255.255.0 SW2:====================== int vl 10 ip add 10.0.0.254 255.255.255.0 PC1:====================== ip 10.0.0.1 255.255.255.0 10.0.0.253 PC2:====================== ip 10.0.0.2 255.255.255.0 10.0.0.253 PC3:====================== ip 10.0.0.3 255.255.255.0 10.0.0.254 PC4:====================== ip 10.0.0.4 255.255.255.0 10.0.0.254 BOTH:===================== int vl 10 no shut DEFAULT-INTERFACE:======== default int gi 0/0 VERIFY:=================== do show vlan brief do show interface trunk ping 10.0.0.1 ping 10.0.0.2 ping 10.0.0.3 ping 10.0.0.4 by Network Savage

[networksavage]

VIDEO 22 in the GNS3 Labs for CCNA 200-301. Be sure to subscribe and check out the rest of the series for the rest of the labs! Here is a link to the first video in the playlist for the Complete GNS3 Labs for CCNA 200-301 Exam: https://www.youtube.com/watch?v=z-P1aNT63XQ&list=PLhHT1w6sU7CNz2hDXrzKjGvufwMqx5a4j In this video we are going to compare the trunk port vs access port. We will explain what a cisco trunk port is for and what a cisco access port is for. Cisco trunk vs access mode comes down to what you need the port to do. A port can either be used for trunking or for access. Access ports are for attaching end devices like computers, phones, printers, etc. Trunk ports are for extending vlans to other devices. We will define what a trunk port is and how to configure cisco trunk ports. We will go through all the main differences between access ports vs trunk ports. We will also look at the definition of an access port. SW1:====================== conf t hostname SW1 vlan 10 name ACCESS exi SW2:====================== conf t hostname SW2 vlan 10 name ACCESS exi MIN-CONFIG-ACCESS:======== int gi 0/0 switchport mode access switchport access vlan 10 MIN-CONFIG-TRUNK:========= #DOT1Q int gi 0/1 switchport trunk encap dot1q switchport mode trunk switchport trunk allowed vlan 10 SW1:====================== int vl 10 ip add 10.0.0.253 255.255.255.0 SW2:====================== int vl 10 ip add 10.0.0.254 255.255.255.0 DEFAULT-INTERFACE:======== default int gi 0/1 VERIFY:=================== do show vlan brief do show interface trunk do ping 10.0.0.253 do ping 10.0.0.254 by Network Savage

[networksavage]

Here is a link to the beginning of this course and playlist for Linux for Network Engineers: https://www.youtube.com/playlist?list=PLhHT1w6sU7CMj-NKi-wQrC0DM0WadS4Bq In this video I am going to install vim in linux ubuntu on gns3. Installing the vim editor in ubuntu is not that difficult but it does require a few steps. This video will show you how to install the vim editor in ubuntu and on a docker container. The linux machine is a docker container. We will be installing the vim editor via command line on debian ubuntu linux. This will be a vim install on a debian container. Commands: vi --version apt remove --assume-yes vim-tiny apt update apt install --assume-yes vim vi --version by Network Savage