wierdcore-blog

[wierdcore-blog]

How to Paint Kitchen Area Cabinets

A new coat of paint can make used, exhausted kitchen cabinets look brand-new again. Comprehensive preparation is essential to successfully painting kitchen cabinets. You can also find out: Painters in Warner Robins for Best Quality ​Services

Size-Up the Job

Wood, wood-laminate, and metal cabinets generally can be repainted without difficulty. Plastic laminate cabinets resist overpainting-- those that can be refinished frequently need unique paints and methods, and results can vary. If your cabinets have plastic laminate surface areas, initially consult an experienced paint dealer, and check a sample of the paint you want to use in an inconspicuous location to guarantee that it will bond to the product.

Flat-front doors and drawers are quickly repainted, however woodwork with raised panels, routed profiles or other architectural detailing will require more time to prep and paint. If the woodwork is warped, terribly worn or harmed, or splitting up at the glued joints, you can decide to buy brand-new unfinished doors and drawers and paint them in addition to your existing cabinets.

Applicator options for repainting consist of spraying, rolling or brushing with either a natural or synthetic bristle brush or a foam brush. All have their advantages and drawbacks; select whichever is most suited to the amount of woodwork to be repainted and your design of working. The very best applicator likewise may depend upon the kind of paint or finish you choose.

Get Rid Of Doors and Hardware

Start by eliminating the cabinet doors and drawers and get rid of all pulls, knobs, latches and other hardware from these parts. Place the hardware and screws in plastic bags inside the cabinets where they will be simple to locate when you're prepared to reassemble whatever (Image 1).

Number each door and its matching location as you eliminate them (Image 2). Do not mix them up or the hinges might not line up correctly when you reinstall them (Image 3). If you are painting just the drawer fronts, you will not have to get rid of the attached slides. If you do require to remove the slides, mark them and their places.

Clean Surfaces

Cooking areas are work areas, so grease, steam, and food splatters are common. Before you begin sanding or painting, tidy all of the surface areas to be repainted with an option made from one part tri-sodium phosphate and four parts water. Rinse, but do not soak the cabinets. Allow them to dry completely.

Sand

Lightly sand the doors on all sides and faces (Image 1). Use a wood sanding block to prevent rounding over the wood edges (Image 2). If your repainting task is just a facelift for the cabinets, you don't need to sand and paint the inside of the cabinets; mask off the interiors with painters' tape for a clean finish and sand just the front surface areas and visible edges of the cabinet face frames.

When sanding, there is no requirement to eliminate all of the old paint if it is sound and well-adhered; simply rough up the surface to supply the brand-new paint with a company, tidy base for better adhesion. Pay particular attention to especially worn locations of the old finish, which typically get the most utilize. Likewise, make certain to sand over shiny locations to deglaze any staying previous surface. Persistent surfaces might require rubbing with denatured alcohol and fine steel wool.

If the old paint is exfoliating in locations, it indicates the surface did not adhere well to the wood surface. This is usually due to wetness or greasy residue getting under the paint layer or into the wood itself, which can be anticipated in kitchens. Sand these areas to bare wood and spot-prime with a stain-killing primer/sealer before repainting. Wherever you sand to bare wood, try to mix or "feather" the edges where the old paint satisfies the wood so the brand-new paint will lay flat, and the paint edges will not be visible or "telegraph" through the brand-new surface.

Thoroughly vacuum the sanding dust from all surfaces (Image 3). If you have a pneumatic air compressor, usage high-pressure air to blow the dust out of crevices or molding information. Clean down the locations to be painted with a tack fabric to get any staying sanding residue

Use Primer-Sealer

Apply an even coat of primer-sealer to all surface areas to ensure a well-bonded finish coat. Primer-sealers also lower the need to sand and deglaze old surfaces before repainting. Another benefit to a primer-sealer is that it provides an excellent base for semigloss, water-based paint. High-gloss enamel paint was once the preferred finish for kitchen area cabinets because it resists discolorations and water and is easily cleaned up, however, today's water-based surfaces are simpler to deal with and offer a similarly durable finish.

Apply the Paint

Start by painting the inside edges and openings of the face frames, then the outer cabinet sides, and lastly the face frame fronts. This allows you to work quickly in the less important areas and enables you to see and fix any drips or spots on the most noticeable locations.

Next, paint the cabinet doors and drawer fronts, in addition to any different wood pieces or moldings (Image 1). If these parts have raised or routed functions, make certain to stream the paint into crevices and corners, however, don't enable it to build up in these areas (Image 2).

Constantly apply paint in thin, light coats, but make certain to cover all areas. Thin coats leave less noticeable brushstrokes and dry faster. Do not lay the surface on heavily and do not strain the brush-- too many brush strokes will create air bubbles in the surface, leaving bumps and pits when it dries.

Enable the paint to dry for at least four hours between coats. When dry, resand all surface areas gently to prepare them for the second coat (Image 3), wipe away all sanding dust with a tack fabric (Image 4), then repaint. Two coats of quality paint are usually all that is needed, however, you may wish to add a 3rd coat because cooking area cabinets take great deals of punishment from cooking heat and day-to-day usage, and wood surface areas require all the security they can get.

[wierdcore-blog]

[wierdcore-blog]