#usb 3.1 device controller | Explore Tumblr posts and blogs

howzitsa · 2 months ago

Photo

Dell Latitude 7320 Core i5-1135G7-16GB DDR4-6RB7HK3 Technical Specifications CONDITION Excellent DISPLAY Display diagonal Display diagonal: 33.8 cm (13.3") Display resolution Display resolution: 1920 x 1080 pixels Touchscreen Touchscreen: No HD type: Full HD Panel type: WVA Native aspect ratio: 16:9 LED backlight LED backlight: Yes Anti-glare screen Anti-glare screen: Yes Display brightness Display brightness: 250 cd/m² Pixel density: 166 ppi Pixel pitch: 0.153 x 0.153 mm Display response rise/fall: 35 ms Maximum refresh rate: 60 Hz Contrast ratio (typical): 800:1 PROCESSOR Processor manufacturer: Intel Processor generation: 11th gen Intel® Core™ i5 Processor family Processor family: Intel® Core™ i5 Processor model Processor model: i5-1135G7 Processor boost frequency: 4.2 GHz Processor cores: 4 Processor cache: 8 MB Processor cache type: Smart Cache Configurable TDP-up frequency: 2.4 GHz Configurable TDP-up: 28 W Configurable TDP-down frequency: 0.9 GHz Configurable TDP-down: 12 W MEMORY Internal memory: 16 GB Internal memory type: LPDDR4x-SDRAM Memory form factor: On-board Memory clock speed: 4267 MHz STORAGE Total storage capacity: 256 GB Storage media: SSD Total SSDs capacity: 256 GB Number of SSDs installed: 1 SSD capacity: 256 GB SSD interface: PCI Express SSD form factor: M.2 Optical drive type: No Card reader integrated: Yes Compatible memory cards: MicroSD (TransFlash), MicroSDHC, MicroSDXC GRAPHICS Discrete graphics card model: Not available On-board GPU manufacturer: Intel On-board graphics card: Yes Discrete graphics card: No On-board graphics card model: Intel Iris Xe Graphics AUDIO Audio chip: Realtek ALC3281-CG Number of built-in speakers: 2 Speaker power: 2 W Built-in microphone: Yes CAMERA Front camera: Yes Video capturing speed: 30 fps NETWORK Mobile network generation: 4G 4G standard: LTE Top Wi-Fi standard: Wi-Fi 6 (802.11ax) Wi-Fi standards: Wi-Fi 6 (802.11ax) Mobile network connection: Yes Antenna type: 2x2 Wi-Fi data rate (max): 2400 Mbit/s WLAN controller manufacturer: Intel WLAN controller model: Intel Wi-Fi 6 AX201 Ethernet LAN: No Bluetooth: Yes Near Field Communication (NFC): Yes PORTS & INTERFACES USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity: 1 USB4 Gen 2x2 ports quantity: 2 HDMI ports quantity: 1 HDMI version: 2.0 Combo headphone/mic port: Yes Charging port type: USB Type-C USB Type-C DisplayPort Alternate Mode: Yes USB Power Delivery: Yes PowerShare: Yes Number of USB ports with PowerShare support: 1 KEYBOARD Pointing device: Touchpad Keyboard language: US International Keyboard backlit: Yes Numeric keypad: No SOFTWARE Operating system architecture: 64-bit Operating system language: Multilingual Trial software: Microsoft Office Operating system installed: Windows 10 Pro PROCESSOR SPECIAL FEATURES Embedded options available: No Intel Virtualization Technology for Directed I/O (VT-d): Yes Intel Virtualization Technology (VT-x): Yes CPU configuration (max): 1 Idle States: Yes Intel VT-x with Extended Page Tables (EPT): Yes Intel Stable Image Platform Program (SIPP): No Intel Software Guard Extensions (Intel SGX): No Intel Trusted Execution Technology: No BATTERY Number of battery cells: 4 Battery voltage: 11.4 V Battery capacity: 63 Wh Removable battery: No Battery recharge time: 3 h Fast charging: Yes Battery weight: 212 g Battery charge indicator: Yes POWER AC adapter power: 65 W AC adapter frequency: 50 - 60 Hz AC adapter input voltage: 100 - 240 V AC adapter output current: 3.25 A AC adapter output voltage: 20 V SECURITY Cable lock slot: Yes Smart card reader: Yes Fingerprint reader: Yes Password protection: Yes Dell ControlVault: Yes OPERATIONAL CONDITIONS Operating temperature (T-T): 0 - 35 °C Storage temperature (T-T): -40 - 65 °C Operating relative humidity (H-H): 10 - 80% Storage relative humidity (H-H): 0 - 95% Operating altitude: -15.2 - 3048 m Non-operating altitude: -15.2 - 10668 m Operating shock: 105 G Non-operating shock: 40 G Operating vibration: 0.26 G Non-operating vibration: 1.37 G WEIGHT & DIMENSIONS Width: 306.5 mm Depth: 199.5 mm Height (front): 1.7 cm Height (rear): 1.84 cm Weight: 1.12 kg

#REFURBISHED #REFURBISHED_LAPTOP #1135G7 #CORE_I5 #CORE_I7 #DDR4 #DELL #INTEL #LAPTOP #LATITUDE_7320

0 notes

bliiot · 3 months ago

Text

ARMxy RK3588J Embedded Edge Device WireGuard for Secure IoT Communication

BL450 Series ARM Embedded Computer is an industrial-grade ARM controller with flexible I/O configuration, based on the Rockchip RK3588J/RK3588 processor, featuring a quad-core ARM Cortex-A76 + quad-core ARM Cortex-A55 + triple-core ARM Cortex-M0 architecture, witha clock speed of up to 2.0G/2.4GHz. It is equipped with 32GB/64GB/128GB eMMC and 4GB/8GB/16GB LPDDR4X RAM and ROM configurations. Supporting a rich set of I/O interfaces, it also integrates a 6TOPS NPU, enabling deep learning capabilities. The BL450 series iswidely used in industrial control, edge computing, AIoT, artificial intelligence, communication management, AGV robots, machine vision inspection, robotics, industrial IoT gateways, energy storage systems, automation control, and transportation infrastructure.

BL450 Series ARM Embedded Computer offers 1 to 3 optional RJ-45 network ports, including two 10/100/1000M ports and one 10/100M adaptive port, along with 2×USB 3.1, one optional HDMI 2.1, and optional X-series and Y-series I/O boards for communication, PWM output, pulse counting, and other data acquisition and control functions. It supports 8K@30fps H.264 video encoding and 8K@60fps H.265 video decoding. Built-in Mini PCIe interface allows support for Bluetooth, WiFi, 4G, and 5G communication modules.

BL450 Series supports multiple operating systems, including Linux-5.10.209, Linux-RT-5.10.209, Ubuntu 20.04, Debian 11, and Android 13. It is also compatible with Docker containers, Node-Red, and Qt-5.15.10 for graphical development. The BLIoTLink industrial protocol conversion software enables fast industrial data acquisition and conversion, facilitating seamless integration with mainstream IoT cloud platforms and industrial SCADA software. Additionally, the BLRAT remote access tool provides remote access and maintenance, while Node-Red allows for rapid IoT application development.

Designed with professional electrical performance and high/low-temperature testing, the BL450 series operates reliably under harsh electromagnetic interference and extreme temperatures ranging from -40°C to 85°C. With DIN35 rail mounting, it is suitable for various industrial applications.

#bliiot #iot gateway #embedded computer #edgecom

0 notes

factorysolution · 6 months ago

Text

What Is An Affordable Embroidery Machine And How Can It Benefit You?

No.01: Introduction to Affordable Embroidery Machines

No.1.1: What is an affordable embroidery machine?

It is new and growing tools stitch into you smart and affordable Embroidery machines like a professional These devices have so many functions that you can create your bespoke designs and complex forms without spending a fortune. With features that are easy to use, such as user-friendly controls, built-in patterns and adjustable stitch lengths, they work for beginners as well as experienced crafters. Aside from quality output, by offering affordable Machines, Brands like JINYU popularize embroidery for hobbyists and small businesses already. In recent years, budget embroidery machines have changed the game for fabric arts, becoming the tool of choice for those wanting to personalize their clothes and accessories as well as their home decor.

No.1.2: Why affordable embroidery machines are popular among hobbyists and professionals

Low-cost embroidery setups have been trending ever because they deliver nice quality results at a value that everyone can afford. By 2025 these machines have never been more trusted with even higher stitch per minute offerings, further designs and larger hoop sizes. More affordable embroidery machines are also budget-friendly options for hobbyists who want to enter the world of custom embroidery without paying for older processes of it, or its commercial-grade device prices. How has technology bridged the gap between a good price and a function — JINYU is making enormous strides in that direction with professional embroidery now literally at your doorstep.

No.02: Key Features of Affordable Embroidery Machines

No.2.1: Stitches per minute and other performance metrics

Some important features to consider when choosing an affordable embroidery machine include stitch speed, user-friendly features, and the number of stitches to choose from. Faster production and efficiency happen when it is the latter, backed up by a higher SPM machine, especially for business needs. Furthermore, machines featuring automatic thread cutting, needle threading assistance, and built-in LCD screens enhance user-friendliness. These features can greatly enhance a small-business or DIY enthusiast's productivity. The embroidery hoop size also matters; the larger the size of the hoop, the large the design can be so fewer setups and, therefore, less time and effort. That said, brands like JINYU have perfected these functions catering to the demands of both new and professional users.

No.2.2: Comparing design capabilities in low-cost models

Another thing to think about when deciding on the right embroidery machine for you is to check their designs. Most machines come with a selection of built-in embroidery patterns, but being able to upload your own is a bonus. Innovative designs flaw because open machines are no more than. DST,. PES, and. EXP is ideal for users who require adding logos or other graphics to a project. Features like USB ports or Wi-Fi capability can turn design transfers into a breeze. Also think about the machine’s durability and construction — while some lightweight models will make transportation less of a hassle, heavy-duty machines generally give better stability and precision for more intricate patterns. Finally, when it comes to choosing the best embroidery machine for the money for your needs, it's also relevant to have in mind how easy is to access customer service and the availability of compatible accessories.

No.03: How to Choose the Best Affordable Embroidery Machine

No.3.1: Factors to consider when purchasing an affordable embroidery machine

No Identical 5: The right way to Buy the Right Best Low-cost Embroidery Machine: You must take into consideration what you might be buying for — interest, small enterprise or big scale enterprise? Entry-level models are designed for beginners and hobbyists; they generally serve up simple features: preprogrammed designs, basic stitch functions, limited setup. But if you’re in business or need complex designs, a pricier machine might be worthwhile since higher-end versions come stacked with advanced features, like automatic thread trimming, more stitching options and larger embroidery displays. Affordable doesn’t have to indicate underpowered, and there are many machines that find a good compromise between the two on today’s market. Along its line of low-cost models, JINYU's more versatile options do not come at the expense of accuracy or model choice so that they mark for a less expensive choice.

No.3.2: How to evaluate machine size, stitch types, and additional features

You have to consider checking the overall functioning and durability before the purchase depending on how frequently you plan to use the embroidery machine. However, if you only plan to use your machine occasionally, then you probably don’t need a ton of options — so a small embroidery field and a handful of stitches may be more than enough for your needs. For the second type user who wants to design a more complex pattern or run a small business, it would most probably need a machine with a larger hoop size and higher stitching speed. Be sure to check reviews from users to see how the machine performs in the real world. Look for remarks about how easy it is to set up, how reliable it is and how well the machine handles different fabrics. Just a bit of research on your part will ensure you select a model that works for your budget and your longer-term needs, so that you’re getting the best possible value from an entry-level embroidery machine.

No.04: Top Affordable Embroidery Machines of 2025

No.4.1: Review of the best entry-level embroidery machines

2025The best affordable embroidery machine includes different options with competitive price, performance and features in 2025. Brands such as JINYU are good exemples of putting together price and on of the good quality tire line, being able to please both, entry level users or small business owners. The JINYU machine, for example, offers high stitches per minute (SPM) along with making it great for almost any beginner as well as professional, with the ability to support embroidery designs. Models come in at this price with how easy they are to use, too, with built-in designs and even LCD screens meaning users can jump straight into the embroidery without much of a learning curve. The combination of affordability and performance is what has made JINYU and other economical brands a hit in the world of embroidery, proving that you can have your cake and eat it too when it comes to quality and lower cost machinery.

No.4.2: Pros and cons of the top budget-friendly models

This shows a show that low cost embroidery machines have come a long way and are no more inferior to high price machines. As a matter of fact, quite a few entry level models have features that used to be exclusive to their pricier alternatives. For example, automatic thread cutting, better stitch functions and bigger embroidery areas are now standard on many budget embroidery machines. If you plan to have your design sent over via a computer or a mobile device, some of the models you'll find out there are wireless-connected, which can make the entire process smoother and quicker. With these improvements — and a substantially lower price point — users can achieve professional-grade results without the hefty investment. The likes of JINYU have made it easy for everyday crafters and small business owners to achieve the kind of professional-quality embroidery you'd find elsewhere for a fraction of the cost.

No.05: How Affordable Embroidery Machines Enhance Creativity

No.5.1: Customizing your designs with low-cost embroidery machines

1:Monotonous sewing machine upkeep is crucial to keep your economical stitching machine working seamlessly. Regular cleaning of the machine will help to avoid thread jams and avoid stitching inconsistency. Regular tasks like oiling the appliance, cleaning the bobbin case, and changing needles regularly can add years to its life. Some of the cheaper models from JINYU and other brands have a self-cleaning function that does run but please still use manual cleaning if needed. By doing so, embroidery machine repairs due to wear and tear will be avoided and production can run smoothly. Also, be sure to adhere to the manufacturer’s servicing guidelines to prevent voiding any warranties.

No.5.2: Practical applications for [affordable embroidery machine]affordable embroidery machines in various crafts

2:Besides regular maintenance, troubleshooting common problems saves time and money as well. Common problems when you are sewing are tension problems, skipped stitches, uneven stitching, but these are usually very easy to fix. The tension issues on the sewing machine can be solved by improving tension adjustment on the other hand, skipping stitches occur because your sewing machine does not use the correct stitch or the machine can be fixed with a new needle. JINYU and other brands of embroidery machines have a plethora of guides on troubleshooting your embroidery machine and these guides empower the user to fix issues that arise without having to get a professional to help them. So bookmark these guides so you know when to seek out customer support for the hard stuff. Your inexpensive embroidery machine can continue to deliver joyously professional results for years, if you care for and use it properly.

No.06: Maintenance Tips for Affordable Embroidery Machines

No.6.1: Cleaning and troubleshooting basic issues

1:Knowing your budget embroidery machine features and restrictions is essential to make the most out of it. Not only are affordable models made to be easy to use, but that's with the understanding that they're only going to be a good option with certain limitations in speed, complexity of design and size of the hoop. Whereas a high-end embroidery machine may be disastrous in small, simple projects, such as with the JINYU affordable embroidery machine, it’ll struggle with large, complex designs with multiple colors but is otherwise great for smaller, simpler projects. That’s precisely why you would want to buy it as a hobbyist or a small business, single color designs with small embroidery areas. Optimising the machine for you to achieve higher performance is the theme that comes from learning how to make more with less without too much, costly hardware.

No.6.2: Extending the lifespan of affordable embroidery machines

2: So, another thing to learn about cheap embroidery machines is how to(machine embroidery on velvet) be used on various types of fabrics. For those of you with an embroidery machine out there, not every single model works on the same types of material. However, while not every budget-friendly model is versatile enough to work on a variety of fabrics (everything from cotton and denim to delicate silks and knits), plenty are, including offerings from epicenter of affordability JINYU. Selecting the correct needle and thread for the appropriate textile is critically important to prevent complications such needle breaks or thread bunching. Adjustable presser feet, as well as stitch lengths are also commonly available settings on the best cheap embroidery machines which help with getting the best result on a range of different types of material. When you learn the proper settings for various fabrics, you really can expand the range of items that your budget embroidery machine can create.

No.07: What to Expect from Affordable Embroidery Machines in 2025?

Choosing the right affordable embroidery machine for you can be determined through weighing the features, performance, and cost. For instance, the JINYU cheap embroidery machine stands out for its fast stitch speed and flexibly wide sewing options, making it easier to tackle both small and bigger projects. Breathable mesh paneling and sturdy cushioning gives it a snappy feel, while the little price tag makes it perfect for collegiate types and those well overdue for an upgrade without needing to take out a second mortgage. It has a big color touch screen, making it simpler to customize the appearance. It provides support for multiple needle types in addition to different weights of thread, increasing the machine’s ability to do embroidery. functionality at cost availability aspect makes the JINYU the best necessary option for hobbyists and small biz owners

No.08: How do affordable embroidery machines compare to high-end models?

The ease of use is one of the best benefits of an inexpensive embroidery machine. Another element of user-friendliness is the JINYU model which comes with an intuitive interface, comes with preloaded embroidery patterns and are easy to understand. These features allow beginners to get started on projects with zero configuration." “ And, most budget models also have automatic needle threaders and at least some adjustments for thread tension, so you also will not have to worry about that! Whether you want to make a personalized gift or start a small business, these machines are easy to play with, fast without the features of the more expensive big boys that make it so difficult to learn on, and designed for instant production.

No.09: When is it time to upgrade from an affordable embroidery machine?

Basic cleaning, which is a critical part of this process, can extend the life of your inexpensive embroidery machine. In like manner, with the JINYU machines, you have to clean the bobbin area or needle plate, you know to maintain your threads from getting stuck. You may also wish to change them out every few projects for the best in stitch quality, especially if you’re working with heavyweight fabrics or have a lot happening in your stitching. Also, for the embroidery machine, change the thread frequently when using it so that, it should not break. If you follow the maintenance guidelines, you could save big on maintenance costs and your machine will work like new. Keep in mind that regular maintenance will help you to get professional grade results from your inexpensive embroidery machine.

No.10: Are affordable embroidery machines suitable for business use?

Every embroidery machine which is on the cheaper side comes up with features that help you with light and heavy fabrics. And, for instance, the JINYU affordable embroidery machine is great for a variety of fabrics like cotton, denim and polyester. A machine capable of handling a range of fabrics, including those that are thicker or textured, has adjustable presser feet and stitch length options. Whether you’re designing intricate patterns on light fabrics or bold designs on thicker materials, the JINYU can keep up. Yet, this omnivorous way with so many fabric types doesn’t come at the cost of stitch quality, which means that you can take on a type of work that goes from custom clothes to home décor and beyond.

No.11: Will affordable embroidery machines meet the demands of professional embroiderers?

Budget-friendly embroidery machines, like the JINYU win model, are perfect for small businesses in need of reliable performance that doesn't break the bank. Other features include automatic thread cutting, adjustable speed control and a wide embroidery area, which means that users can work on large projects with precision. For instance, if you are employed at a personalized apparel shop with very few employees, you can easily produce professional-quality logos or custom-made works for your customers with an inexpensive embroidery machine. Most budget embroidery machines come with USB ports which are used to transfer designs from your computer and other electronic devices directly to them. Moreover, the ability to seamlessly integrate with various design software platforms is an ideal opportunity for creative entrepreneurs.

No.12: Can beginners use affordable embroidery machines effectively?

A low-cost sewing machine such as JINYU model is also one that has lots of customer support, and is going to hold up for a while. Most of the machines indeed contain even a detailed user manuals, and some sprinkle ql tutorials to assist the user with the embroidery. Thisis in addition to troubleshooting guides and a supportive team to assist you through it if you are experiencing some of the most common struggles associated with sewing pulp such as adjusting your thread tension or swapping out your bobbin. This commitment to customer service ensures a worry-free experience with their machine for both hobbyists and professionals alike. This is a significant factor, as first-time buyers want peace of mind in selecting the right machine for their embroidery business or craft projects.

No.13: Does the embroidery quality of affordable machines hold up over time?

Hobbyists running creative DIY projects also get a lot from these affordable embroidery machines that not just work for small business but also other activities. You can set up these machines differently and you can work with this machine using any kind of stitch. A low-cost embroidery machine can also make it easy for novices at home to create personalized embroidered towels or bags, costing significantly less than what you would pay at a commercial service. Home embroidery is perfect for hobbyists who want to try their hand at embroidery without having to commit to a costly industrial machine. With convenient features like automatic needle threading and integrated design libraries, these machines are user-friendly and perfect for those dipping their toes into embroidery.

No.14: Which accessories are essential for affordable embroidery machines?

A lot are on the lookout for embroidery machine that offers professional quality but without the professional price. All the professional attributes (whether it is multi-needle, high-speed and so on) used by high-end embroidery machines are used by JINYU, so the large manufacturers we can equip with machine embroiderer can also be very good! This is why they’re numbered as a favorable alternative for those who want to offer a bit of everything in terms of embroidery services — from custom logos to intricate designs — without paying for more expensive commercial embroidery machines. That means a JINYU’s particular embroidery machine like the inexpensive one we discussed are a clear best-fit option for home businesses and creative pros alike—the best price-performance-quality value ratio. Such machines lower total project times, meaning users can spend hours being productive without noticing an impact on the quality of their output.

No.15: Reference

#Reference SourceLink1Wikipedia - Embroidery Machinehttps://en.wikipedia.org/wiki/Embroidery_machine2The Spruce Crafts - Best Embroidery Machineshttps://www.thesprucecrafts.com/best-embroidery-machines-48405563Sewing Machine Club - Best Budget Embroidery Machineshttps://www.sewingmachineclub.com/best-budget-embroidery-machines/

youtube

#tech #embroidery #embroiderymachines #Youtube

0 notes

portablegeneratorsreview · 7 months ago

Link

#AIVOLT1200Wpetrolinvertergenerator #PetrolInverterGenerator #Portablepower #Silentoperation

0 notes

johngarrison1517 · 8 months ago

Text

VCM Actuator Integration: Maximizing 2MP Resolution in USB 3.1 Cameras

Use of a 2MP USB 3.1 camera may make you question whether you're getting the most out of it. Sharp, detailed images are promised by high-resolution cameras, but these promises may not be fulfilled in the absence of accurate focusing systems. The Voice Coil Motor (VCM) actuator is used in this situation. However, what is a VCM actuator, and how might it improve your camera system's performance? This post will discuss how adding a VCM actuator can enhance the performance of 2MP USB 3.1 cameras and solve typical issues like image quality and focus accuracy.

What Is a VCM Actuator, and Why Does It Matter?

A VCM actuator is a type of focusing mechanism used in camera modules to adjust the lens position for optimal focus. Unlike stepper motor systems, which can be slower and less efficient, VCM actuators use electromagnetic force to move the lens with speed and precision. This fine control over the lens position ensures sharper focus and better overall image quality.

In the realm of 2MP USB 3.1 cameras, integrating a VCM actuator can mean the difference between an average photo and an exceptionally detailed one. This is particularly valuable in applications like industrial inspection, medical imaging, and video conferencing, where even slight focus inconsistencies can affect the final output quality.

Image Quality and Speed

Many camera users face the problem of achieving rapid focus without sacrificing image quality. A poorly focused image can lead to frustration, decreased productivity, and missed opportunities. Whether it’s a technician trying to conduct a detailed inspection or a user participating in a video call, achieving and maintaining sharp focus is critical.

Traditional focusing systems can struggle with quick adjustments, especially in dynamic environments where the distance between the camera and the object can change frequently. VCM actuators address this pain point by offering faster and more precise focus capabilities.

How VCM Actuators Maximize 2MP USB 3.1 Camera Performance

Enhanced Focus Speed: One of the standout benefits of a VCM actuator is its fast response time. For a 2MP USB 3.1 camera, which already processes a significant amount of data at high speed, this rapid focus adjustment means that users can capture clear images without any delay. This is particularly useful for live applications where timing is critical, such as telemedicine or remote surveillance.

Improved Image Stability: A major challenge in achieving consistent image quality is stability during focus adjustments. VCM actuators allow for smooth and gradual lens movements, which translates to stable image output. For customers who need reliable camera performance in high-stakes settings, such as diagnostic imaging or machine vision, this stability is essential.

Minimized Motion Blur: Quick and precise lens adjustments help minimize motion blur. Motion blur can be especially problematic in industrial settings where machinery or conveyor belts are in motion. A VCM actuator helps maintain sharp images even in environments with rapid movement, enabling more accurate data collection and analysis.

Compact and Lightweight Design: Modern 2MP USB 3.1 cameras are valued for their compact size and versatility. The VCM actuator fits well within these compact modules, maintaining a sleek form factor without adding bulk. This makes it ideal for use in portable devices and embedded systems where space is at a premium.

Customer Utility: Practical Applications of VCM Actuators in 2MP USB 3.1 Cameras

Integrating a VCM actuator into a 2MP USB 3.1 camera opens up a variety of practical applications:

Medical Imaging: Medical professionals rely on high-resolution cameras for diagnostics. A VCM actuator ensures that images remain clear and detailed, making it easier to detect abnormalities and make accurate diagnoses.

Quality Control: In manufacturing, even minor defects can lead to costly recalls. A 2MP USB 3.1 camera equipped with a VCM actuator can provide the detailed imaging needed to catch issues early and maintain quality standards.

Retail and security: surveillance cameras in stores and public areas need to adjust focus rapidly as people move through different areas. The quick focus capabilities of a VCM actuator improve the efficiency and reliability of security systems.

Addressing Common Pain Points

Despite the benefits, some customers may worry about compatibility or the learning curve of implementing VCM actuator technology. The good news is that modern VCM actuators are designed to integrate seamlessly with most camera systems, including 2MP USB 3.1 models. Furthermore, software support ensures that the actuator can be controlled easily, simplifying the user experience.

For developers, the integration process is straightforward. Most camera modules with VCM actuators come with SDKs (software development kits) that make configuration simple, even for those new to this technology.

How to Choose the Right VCM-Integrated Camera

When looking for a camera with a VCM actuator, consider the following:

Compatibility: Ensure that the camera model supports USB 3.1 for faster data transfer.

Use Case: Think about how and where you will use the camera. For instance, a medical professional might need different focus speeds and precision compared to an industrial inspector.

Budget: While VCM-equipped cameras may come at a higher price point, their long-term value in terms of performance and reliability often justifies the investment.

Final Thoughts: Make the Smart Move to VCM Actuators

Are you tired of mediocre focus and inconsistent image quality? Upgrading to a 2MP USB 3.1 camera with a VCM actuator might be the solution you’ve been searching for. With rapid focus adjustments, enhanced stability, and compact design, these actuators offer substantial improvements over traditional focusing systems. The technology addresses key pain points like slow focus and motion blur, providing clearer, more reliable imaging for your critical applications.

Ready to transform your camera experience? Invest in VCM actuator technology today and see the difference in your 2MP USB 3.1 camera’s performance.

Learn how integrating a VCM actuator can transform the capabilities of your camera. For additional information on selecting the ideal VCM-equipped camera for your requirements, get in touch with our professionals right now.

#VCM actuator #USB 3.1 camera #camera technology #high-resolution imaging

0 notes

sanaavay · 10 months ago

Text

Features THE H-SERIES PC CASE The H510 Elite compact ATX mid-tower is perfect for your RGB build. Behind the flush-mounted, tempered glass front panel, youâ€™ll discover our renowned Aer RGB 2 fans keeping your components brilliantly cool. Well-engineered airflow, removable radiator mounting bracket, multiple fan filters, vertical GPU mount, a front panel USB-C connector, and an all-steel and tempered glass construction are just some of the key features youâ€™ll get. The H510 Elite also includes the NZXT Smart Device V2, powering the built-in RGB light strips and case fans. BEAUTIFUL CRAFTMANSHIP Two tempered glass panels top off your build, perfectly showcasing your RGB build. Weâ€™ve included two Aer RGB 2 fans and an RGB LED strip to get you started. The H510 Elite features a removable radiator mounting bracket, simple-to-use SSD trays, and a patented cable management system for a smarter, easier build experience. The new Smart Device 2 includes two HUE 2 RGB lighting channels, and three fan channels that support 0dB modes for voltage-regulated or PWM fans. The USB 3.1 Gen 2-compatible USB-C connector on the front panel makes it easier than ever to connect smartphones, high-speed external storage, and the latest peripherals to your PC. The clean, modern design, iconic cable management bar, and uninterrupted tempered-glass panels all showcase your stunning build. Use the intuitive NZXT CAM application to monitor and control your build, choosing from presets or custom controls for your RGB lighting and fans to create your dream PC. Specifications Model Number CA-H510E-B1 Dimensions W: 210mm H: 435mm D: 428mm (without feet) W: 210mm H: 460mm D: 428mm (with feet) Material(s) SGCC Steel and Tempered Glass Motherboard Support ATX I/O Ports 1x USB 3.1 Gen 2 Type-C 1x USB 3.1 Gen 1 Type-A 1x Headset Audio Jack Filters All Air Intakes Expansion Slots 7 Smart Device 3x Fan channels with Max 10W per channel output* 2x RGB LED channels, each support up to 4x HUE 2 LED strips or 5x Aer RGB 2 fans Built-in noise detection module *Note : If a splitter is used, fan control is regulated depending on the fan connected to the 4-pin port . Do not use low-noise adapters. System Requirements PC with open internal USB 2.0 port and WindowsÂ® 10 operating system recommended. Internet connection is needed to download CAM. Some CAM features require Internet access, a valid email address and acceptance of our current Terms of Service. LED Strips 1 integrated RGB LED strip No additional strips included. Drive Bays 2.5â€: 2+1 3.5â€: 2+1 Radiator Support Front: 2x 140 or 2x 120mm with Pull Rear: 1x 120mm Fan Support Front: 2x 120/ 2x 140mm (2x AER RGB 2 140mm included) Top: 1x 120mm/ 1x 140mm (1x AER F140 Case Version Included) Rear: 1x 120mm (1x AER F120 Case Version Included) Fan Specs Aer RGB 2 (140mm) Speed: 500-1,500 RPM Airflow: 30.39 – 91.19 CFM Noise: 22 – 33 dBA Air Pressure: 0.17 â€“ 1.52mm-H2O Bearing: Fluid Dynamic Bearing Fan Connector 4-Pin PWM Clearance Cable Management: 19-23mm GPU Clearance: Up to 368.5mm Vertical GPU Mount Clearance: 40.64mm CPU Cooler: Up to 165mm Front Radiator: 60mm Rear Radiator: 60mm Reservoir & Pump: Up to 180mm (Along cable bar), Up to 86mm (Along bottom panel) Warranty 2 Years Note ***Features, Price and Specifications are subject to change without notice.

0 notes

sanmeiglobal998 · 10 months ago

Text

Power Delivery 3.1 Charger: The Ultimate Guide to the Future of Fast Charging!

As our reliance on electronic devices continues to grow, so does the demand for faster and more efficient charging solutions. Enter the Power Delivery 3.1 (PD 3.1) charger, the latest innovation in charging technology. Whether you’re powering up a smartphone, tablet, laptop, or even more demanding devices, a PD 3.1 charger offers unparalleled speed and versatility. In this article, we’ll explore what makes Power Delivery 3.1 a game-changer in the world of charging, and why it’s time to upgrade to this advanced technology. What is Power Delivery 3.1? Power Delivery 3.1 is the newest version of the USB Power Delivery standard, designed to provide more power and faster charging speeds than its predecessors. While previous versions like PD 2.0 and 3.0 could deliver up to 100W of power, PD 3.1 takes it a step further by supporting up to 240W. This makes it ideal not only for smartphones and tablets but also for laptops, monitors, and other high-power devices. Key Features of Power Delivery 3.1 Chargers - Increased Power Output: One of the most significant upgrades in PD 3.1 is its ability to deliver up to 240W of power. This is achieved through the use of Extended Power Range (EPR) cables and connectors, which are specially designed to handle higher wattages. - Faster Charging Speeds: With more power comes faster charging. PD 3.1 chargers can significantly reduce the time it takes to charge your devices, making it perfect for those who are always on the go and need quick power-ups. - Universal Compatibility: PD 3.1 is designed to work with a wide range of devices, from smartphones and tablets to laptops and beyond. Its universal compatibility means you can use a single charger for all your devices, reducing clutter and simplifying your charging routine. - Enhanced Safety Features: Safety is always a concern with high-power chargers, and PD 3.1 addresses this with advanced safety protocols. These include over-voltage protection, over-current protection, and temperature control, ensuring that your devices are charged safely without the risk of damage. Why Upgrade to a Power Delivery 3.1 Charger? - Future-Proof Your Charging Setup: As more devices adopt the PD 3.1 standard, having a compatible charger ensures you’re ready for the future. Whether you’re upgrading your laptop, buying a new smartphone, or adding a high-resolution monitor to your setup, a PD 3.1 charger will keep all your devices powered efficiently. - Charge Multiple Devices: PD 3.1 chargers often come with multiple ports, allowing you to charge several devices simultaneously. This is perfect for users with multiple devices who want to streamline their charging setup. - Portable and Travel-Friendly: Despite their increased power output, PD 3.1 chargers are typically compact and easy to carry. This makes them ideal for travelers or anyone who needs to charge their devices on the go. - Improved Energy Efficiency: PD 3.1 chargers are designed to be more energy-efficient, reducing power wastage and saving on electricity costs. This is not only better for your wallet but also for the environment. Top 5 Power Delivery 3.1 Chargers to Consider - Acer PD Charger 100W - Why It’s Recommended: Acer Power Delivery technology ensures efficient, high-speed charging while keeping the charger compact and portable. It’s an excellent choice for those who need a powerful charger that won’t take up much space. - Key Features: PD technology, multiple charging ports, advanced safety features. - RAVPower 100W PD 3.1 Charger - Why It’s Recommended: Known for its reliability and performance, RAVPower’s 100W PD 3.1 charger is perfect for powering up laptops, smartphones, and other high-demand devices quickly and safely. - Key Features: Multiple device support, portable design, robust safety features. - Baseus 140W USB-C Charger - Why It’s Recommended: Baseus offers a budget-friendly option without compromising on power or safety. This charger is ideal for users who need fast charging at an affordable price. - Key Features: Affordable, high power output, compact design. - Apple 140W USB-C Power Adapter - Why It’s Recommended: For Apple users, this charger is a no-brainer. It’s designed specifically for the latest MacBook Pro models but is also compatible with other PD 3.1 devices. - Key Features: Apple-certified, high compatibility with Apple devices, reliable performance. - Satechi 165W USB-C 4-Port PD Charger - Why It’s Recommended: Satechi’s charger is perfect for users with multiple devices, offering four USB-C ports that can charge laptops, tablets, smartphones, and more simultaneously. - Key Features: High power output, multiple ports, sleek design. How to Choose the Right Power Delivery 3.1 Charger When selecting a PD 3.1 charger, consider the following factors: - Device Compatibility: Ensure the charger is compatible with your devices. While most PD 3.1 chargers support a wide range of devices, it’s essential to check that your specific device can utilize the charger’s full potential. - Portability: If you travel frequently or need a charger for on-the-go use, opt for a compact and lightweight model. - Budget: PD 3.1 chargers come in a range of prices. Determine your budget and choose a charger that offers the best value for money without sacrificing quality or safety. - Safety Features: Look for chargers that include safety features such as over-voltage protection, temperature control, and short-circuit protection to keep your devices safe. The Benefits of Power Delivery 3.1 for Various Devices - Smartphones and Tablets: Experience faster charging times and reduce the downtime between uses. - Laptops: Power even the most demanding laptops quickly and efficiently, making PD 3.1 chargers ideal for work and play. - Monitors and Other High-Power Devices: Use a single charger to power multiple high-wattage devices, simplifying your workspace. Conclusion The Power Delivery 3.1 charger represents the cutting edge of charging technology, offering more power, faster speeds, and greater compatibility than ever before. Whether you’re a tech enthusiast, a professional, or simply someone who wants the best for their devices, upgrading to a PD 3.1 charger is a smart investment in the future of fast charging. Choose the right charger for your needs and enjoy the convenience, efficiency, and safety that Power Delivery 3.1 brings to the table. With PD 3.1, you’re not just charging your devices—you’re powering your life with the latest and greatest technology available. Read the full article

0 notes

atplblog · 2 months ago

Text

Price: [price_with_discount] (as of [price_update_date] - Details) [ad_1] Product Description CableCreation USB3.1 A to C data cable / fast charging cable Type: USB 3.1 Type-A to Type-C CableLength: 1.0m/3.3Feet, 1.5m/5Feet, 0.5m/1.6FeetColor: Black+GrayData Transfer Speed: 10GbpsMaterial: Premium Aluminum Alloy CoverCharging & Sync: Supports safe fast charging and data transfer Kindly reminder: This USB-A to USB-C cable does not support to transfer data or charging between two hosts (two laptops), USB A for hosts or chargers, USB C for devices.The cable works with USB-C devices, but it does not work with iPhones, iPhone needs a lightning cable.This cable is used to transfer data or charge, it could not deliver 4K video. 4K video USB C cable, Search ASIN: B072M7GH29 B07Q43S8NYBefore purchasing, make sure this is the length you need. USB A to USB C Cable This USB 3.1 A to C cable is an ideal charging and data cable for your daily life and work, to use at the home, office, in your car even on your travel. Just enjoy your leisure time laying on the sofa or bed while charging and playing with your phone. iPad Air, iPad Mini, iPad ProiMac, MacBook Pro, MacBook Air, Mac miniPixel 5/ 4/ 3XL/ 2/ 2XL/ XL / Pixel CGalaxy Z Flip/S23/S23+/S23 Ultra/ S22 /S22 Ultra/S21/ S20/ S10/ S10+ / S9Xbox wireless controller, Stylus pen (With USB C port)More other USB C Laptops, smartphones, tablets, external hard drives, etc.Great cables for the android Auto set up. (With USB-C port: Please check whether your Android Auto supports the OTG function. If so, please check whether the OTG function in the system is enabled.) If you're not sure whether our Cable is compatible with your Device, Please feel free to ask us. High-quality Materials A gold-plated connector ensures maximum signal quality and stable signal transmission.Premium aluminum alloy shells make the cable more durable, it looks fashionable and perfectly matches your expensive devices.This cable is a bit stiff , Due to the number of wires in them meterials, USB data cables are usually thicker than USB charging cables and as durable as well. Durable and long cable Newly-designed cable and mold.Durable cable with copper braid inside to provide better EMI performance.5 Feet long cable to reach more space. Premium Material - The premium material used in the production of our CableCreation items, we tested with other's item, and we are sure it provides a greater degree of cable durability, stability and long life; Premium aluminum alloy shell and gold-plated connector add additional durability and stability to this cable, which makes it more durable than normal cables, a must-have for daily use.

Add to Cart Add to Cart Add to Cart Add to Cart Customer Reviews 4.1 out of 5 stars 35,411 4.3 out of 5 stars 2,305 4.3 out of 5 stars 2,305 4.1 out of 5 stars 35,411 Price ₹909.30₹909.30 ₹3,739.00₹3,739.00 ₹3,569.00₹3,569.00 ₹1,519.00₹1,519.00 Length 6 inch 16 feet 16 feet 6 inch Data transfer 480Mbps 5Gbps 5Gbps 480Mbps Feature charging/ data transfer/portability VR gaming VR gaming charging/ data transfer/portability USB 3.2 10Gbps Data Transfer: Gen2 USB 3.2 Type-C to Type-A Cable supports super speed data transmission up to 10Gbps. You can transfer HD movies or songs in seconds with your USB C SSD (Note: This cable does not support data transfer or charging between two laptops, nor does it support video output, USB 3.2 is backwards Compatible with USB 3.1, USB 3.0, USB 2.0.) Support output Power up to 3 Amp: charge your pc, laptop, tablet or phone up to 3A with your USB-A charger. built-in with 56kΩ resistor to ensure safe charging, protect your devices from damage. Compatible with Qualcomm Quick Charge 3.0. Great Compatibility: This A to C cable compatible with USB C External SSD and other USB-C/Thunderbolt 3 devices. If you are not sure with your device, please tell us and we'll answer your ask. Premium Aluminum Alloy: Premium aluminum alloy shell and gold-plated connector add additional durability and stability to this cable, which makes it more durable than normal cables, a must-have for daily use. What You’ll Get: 1.6FT CableCreation USB A to C cable, with our 24-month product replacement warranty and lifetime 24/7 friendly technical support.

[ad_2]

0 notes

digitalmore · 3 months ago

Text

#IFTTT #DigitalMore.co

0 notes

howzitsa · 6 months ago

Photo

HP EliteDesk 800 G2 Mini Intel Core i5 6th 65W Designed for every demand Blast through your most demanding challenges with the uncompromising performance of 6th Gen Intel® Core™ processors,[2] Intel® HD 530 Graphics, and optional high-end discrete graphics and HP Turbo Drive.[3] Seriously secure Help protect your PC and maintain maximum uptime with a suite of solutions that help stop security breaches, including HP BIOSphere[4] with SureStart. Make durability a reality Get the reassurance of a PC that goes through 120,000 hours of HP Total Test Process and is designed to pass MIL-STD testing.[5] Add an optional Dust Management Solution for enhanced reliability in dusty environments. Expand with ease Extend the life of your investment with a toolless chassis and a range of expansion slots, bays, ports, and connectors for the most demanding business needs. SPECIFICATIONS: General Platform Technology Intel vPro Platform Type Personal computer Product Form Factor Mini desktop Built-in Devices Speaker, hood sensor Embedded Security Trusted Platform Module (TPM 1.2) Security Chip Localization Language: English / region: United States Processor / Chipset CPU Intel Core i5 (6th Gen) 6500T Clock Speed 2.5 GHz Max Turbo Speed 3.1 GHz Number of Cores Quad-Core CPU Upgradability: Upgradable Processor Main Features: Intel Turbo Boost Technology 2 CPU Socket: LGA1151 Socket Chipset Type: Intel Q170 Cache Memory Installed Size: 6 MB Cache Per Processor: 6 MB RAM Installed Size: 8 GB Technology: DDR4 SDRAM - non-ECC Effective Memory Speed: 2133 MHz Rated Memory Speed: 2133 MHz Memory Specification Compliance PC4-17000 Form Factor: SO-DIMM 260-pin Slots 2 (total) / 1 (empty) Features Unbuffered, dual channel memory architecture Configuration Features: 1 x 8 GB Hard Drive Type: HDD Capacity: 1 x 500 GB Interface Type: SATA 6Gb/s Spindle Speed: 7200 rpm Storage Controller Type: 1 x SATA Controller Interface Type: SATA 6Gb/s Optical Storage Type: No optical drive Graphics Controller Graphics Processor: Intel HD Graphics 530 Dynamic Video Memory Technology Video Interfaces: VGA, DisplayPort HDCP Compatible: Yes Max Monitors Supported: 3 Audio Output Sound Output Mode Stereo Max Sampling Rate 192 kHz Compliant Standards High-Definition Audio, DTS Studio Sound Input Device Type Mouse, keyboard Keyboard Keyboard Name HP Business Slim Keyboard Interface USB Localization & Layout US Mouse Interface USB Networking Ethernet Controller Intel I219-LM Wireless LAN Supported Yes Wireless NIC Intel Dual Band Wireless-AC 8260 Data Link Protocol Ethernet, Fast Ethernet, Gigabit Ethernet, IEEE 802.11b, IEEE 802.11a, IEEE 802.11g, IEEE 802.11n, Bluetooth 2.1 EDR, IEEE 802.11ac, Bluetooth 4.1 Remote Management Protocol DMI Features Wake on LAN (WoL), PXE support, auto-uplink (auto MDI/MDI-X) Compliant Standards IEEE 802.2, IEEE 802.3, IEEE 802.3u, IEEE 802.3i, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.11b, IEEE 802.11a, IEEE 802.11g, IEEE 802.11i, Wi-Fi CERTIFIED, IEEE 802.11n, IEEE 802.3az Expansion / Connectivity Bays 1 (total) / 0 (free) x internal 2.5" x 1/8H Slots 1 (total) / 0 (free) x CPU | 2 (total) / 1 (free) x SO-DIMM 260-pin | 1 (total) / 0 (free) x M.2 Card (x1 mode) | 1 (total) / 1 (free) x M.2 Card (x4 mode) Interfaces 1 x headphones - mini-jack (1 in front) | 1 x headphones/microphone - mini-jack (1 in front) | 1 x USB-C 3.0 (1 in front) | 6 x USB 3.0 (2 front, 4 rear) | 1 x VGA | 2 x DisplayPort | 1 x LAN (Gigabit Ethernet) - RJ-45 Miscellaneous Theft/Intrusion Protection Security lock slot (cable lock sold separately) Security Slot Type Kensington security slot VESA Mounting Interface 100 x 100 mm Compliant Standards ACPI, CCC, CECP, SEPA, low halogen Manufacturer Selling Program HP Smart Buy Power Device Type Power adapter Voltage Required AC 120/230 V (50/60 Hz) Power Provided 65 Watt Efficiency 89% Power Factor Correction Yes (active) Operating System / Software OS not provided Environmental Standards ENERGY STAR Certified Yes

#REFURBISHED #REFURBISHED_DESKTOP #6TH_GEN #CORE_I5 #ELITEDESK_800_G2 #HP #INTEL #MICRO #SMALL_FORM_FACTOR #TPC_P055_DM

0 notes

flora-819 · 10 months ago

Text

Exploring PCIe Slots and Their Versatile Uses

Introduction

Peripheral Component Interconnect Express (PCIe) slots are integral to modern computing systems, serving as the interface for a wide array of expansion cards. The PCIe interface, known for its high-speed data transfer capabilities, has become a standard for connecting components and peripherals to a motherboard. This article explores the various applications of PCIe slots, focusing on their versatility and the types of expansion cards they support.

Understanding PCIe Slots

PCIe slots are designed to accommodate expansion cards through a card edge connector, a key feature that allows these cards to be inserted into the motherboard. This card edge connector consists of a series of metal contacts that align with corresponding pins in the PCIe slot, ensuring a stable electrical connection. PCIe slots come in different sizes and configurations, including x1, x4, x8, and x16, which denote the number of data lanes available for communication.

Types of Expansion Cards

Graphics Cards (GPUs) One of the most common uses for PCIe slots is to install graphics cards. These cards, often referred to as GPUs (Graphics Processing Units), are essential for rendering complex graphics and performing computational tasks. High-end gaming, video editing, and 3D rendering applications demand powerful GPUs, which are typically installed in x16 PCIe slots to leverage maximum bandwidth and performance.

Network Interface Cards (NICs) Network Interface Cards enhance a computer's connectivity by providing additional Ethernet ports or supporting advanced networking features. While most motherboards come with built-in Ethernet ports, dedicated NICs can offer higher speeds, better reliability, or additional networking functionalities, such as dual or quad-port configurations. These cards are commonly installed in x1 or x4 PCIe slots, depending on their performance requirements.

Storage Controllers PCIe slots are also used for installing storage controllers, including those for NVMe (Non-Volatile Memory Express) SSDs (Solid-State Drives). NVMe SSDs, which offer significantly faster data transfer speeds compared to traditional SATA SSDs, can be installed directly into M.2 slots on the motherboard or through dedicated PCIe expansion cards. These controllers are crucial for enhancing data storage performance in both consumer and enterprise systems.

Sound Cards For users requiring advanced audio capabilities, sound cards are a popular choice. While integrated audio solutions are sufficient for general use, dedicated sound cards can offer superior audio quality, support for surround sound, and enhanced audio processing features. These cards are typically installed in x1 PCIe slots and are favored by audiophiles and professionals in the music and film industries.

Capture Cards Capture cards are essential for video production, streaming, and gaming. They allow users to capture and record video from external sources, such as cameras, game consoles, or other media devices. Capture cards, which often require substantial bandwidth to handle high-definition video signals, are usually installed in x4 or x8 PCIe slots to ensure smooth operation and minimal latency.

RAID Controllers RAID (Redundant Array of Independent Disks) controllers manage multiple hard drives or SSDs to improve performance, increase storage capacity, or provide data redundancy. RAID controllers can be installed in PCIe slots to facilitate complex storage configurations, such as RAID 0, RAID 1, RAID 5, or RAID 10. These controllers are particularly valuable in server environments or for high-performance computing tasks.

USB Expansion Cards USB expansion cards add additional USB ports to a system, which can be useful for users who require more connectivity options than what is provided by the motherboard. These cards can offer USB 3.0, USB 3.1, or even USB-C ports, enhancing the versatility of a system’s connectivity options. Depending on the card’s design and the number of ports, they may be installed in x1 or x4 PCIe slots.

Wi-Fi and Bluetooth Cards While many motherboards now come with integrated Wi-Fi and Bluetooth, dedicated expansion cards can provide better connectivity options or support for newer standards. These cards are particularly useful in systems where integrated wireless capabilities are not available or where higher performance is desired. Typically, these cards are installed in x1 PCIe slots.

Additional PCIe Slots Expansion Cards For users with motherboards that have limited PCIe slots, expansion cards that provide additional PCIe slots can be installed. These cards effectively allow users to expand the number of available PCIe slots, enabling the installation of more expansion cards than the motherboard originally supports. These are generally used in high-performance workstations or servers where multiple cards are necessary.

Choosing the Right PCIe Slot

When selecting an expansion card, it’s essential to choose the appropriate PCIe slot based on the card’s bandwidth requirements and the slot’s size. For instance, high-performance GPUs and RAID controllers typically require x16 slots to fully utilize their capabilities. Conversely, NICs, sound cards, and USB expansion cards often function well in x1 slots.

Conclusion

PCIe slots, with their card edge connectors, provide a versatile platform for expanding the capabilities of a computer system. From enhancing graphics performance with GPUs to improving connectivity with network and USB cards, PCIe slots play a crucial role in modern computing. Understanding the different types of expansion cards and their corresponding PCIe slot requirements enables users to build or upgrade systems tailored to their specific needs, whether for gaming, professional work, or general computing.

#connector #pcie #card edge #pcie card edge

0 notes

digidarshini · 11 months ago

Text

JBL Bar 3.1 Soundbar with Wireless Subwoofer

The JBL Bar 3.1 Soundbar with Wireless Subwoofer is a high-performance audio system designed to enhance your home entertainment experience. Here’s an overview of its key features and benefits:

Key Features:

1. Sound Quality:

450W Total System Power: Delivers powerful, room-filling sound that enhances movies, music, and gaming experiences.

3.1 Channel Configuration: Provides clear and precise audio with dedicated left, center, and right channels for accurate sound localization.

Wireless Subwoofer: The 10-inch wireless subwoofer adds deep, impactful bass, making explosions, music beats, and other low-frequency sounds more immersive.

2. Design:

Sleek and Modern: The soundbar features a slim, elegant design that fits well with any home decor and can be easily mounted on the wall or placed on a TV stand.

LED Display: An intuitive LED display on the soundbar shows volume level, input source, and sound mode, making it easy to use.

3. Connectivity:

4K Ultra HD Pass-Through: Ensures the best picture quality from 4K devices by supporting 4K video pass-through.

HDMI ARC: Simplifies your setup by allowing audio to be sent from your TV to the soundbar with a single HDMI cable.

Multiple Input Options: Includes HDMI, Optical, USB, and AUX inputs, providing versatile connectivity to various devices such as TVs, Blu-ray players, gaming consoles, and more.

Bluetooth Connectivity: Enables wireless streaming of music from your smartphone, tablet, or other Bluetooth-enabled devices.

4. User-Friendly:

Remote Control: Comes with a user-friendly remote control for easy adjustment of settings, input selection, and volume control.

One-Touch Control: HDMI ARC and CEC support enable you to control both your soundbar and TV with a single remote.

5. Sound Modes:

Dedicated Sound Modes: Features different sound modes, including Movie, Music, Voice, and Sports, allowing you to optimize the audio output based on the content you are enjoying.

Performance:

The JBL Bar 3.1 Soundbar with Wireless Subwoofer delivers excellent audio performance, making it a great addition to any home theater setup. With 450W of total power and a 10-inch wireless subwoofer, it provides robust sound and deep bass that enhance the overall listening experience. The 3.1 channel setup ensures clear dialogue and precise audio placement, making your movies, music, and games more immersive.

Pros:

Powerful 450W total system power.

Deep, impactful bass with a 10-inch wireless subwoofer.

4K Ultra HD pass-through for optimal video quality.

Multiple connectivity options, including HDMI ARC and Bluetooth.

Sleek and modern design with an intuitive LED display.

Dedicated sound modes for different types of content.

Cons:

May be more expensive than basic soundbars.

The large subwoofer might require additional space.

Conclusion:

The JBL Bar 3.1 Soundbar with Wireless Subwoofer is an excellent choice for anyone looking to upgrade their home audio system. It combines powerful sound output, deep bass, and versatile connectivity options in a sleek, user-friendly package. Whether you're watching movies, listening to music, or playing games, this soundbar provides a high-quality audio experience that brings your entertainment to life.

#buy jbl sound bar #jbl sound bar price

0 notes

forlinx · 1 year ago

Text

Forlinx FET3588J-C: Hardware Solution Customized for Marine Instrument Panel Technology

Marine instrument panels are critical display and monitoring devices on ships, crucial for ensuring maritime safety, efficiency, and comfort. Real-time monitoring of vital ship information such as position, speed, heading, and engine status through marine instrument panels enables prompt adjustments and decision-making. They not only enhance the precision and reliability of ship operations but also help reduce accident risks, ensuring safe navigation. Moreover, the digital and intelligent design of marine instrument panels allows crew members to manage and control ships more efficiently, improving operational efficiency. They are key tools for ship operation and management.

With the continuous advancement of maritime technology, there is an increasing demand for intelligence and digitization in modern ships. As a core component for ship information display and monitoring, the performance and stability of marine instrument panels are crucial to meet modern maritime needs for information display, data monitoring, and navigation safety. Specific objectives include:

Providing a clear and intuitive instrument display interface enables crew members to quickly access navigation information.

Facilitating compatibility with various data interfaces enables seamless data transmission with onboard sensors and equipment.

Ensuring that instrument panels can operate stably in harsh maritime environments, with high resistance to interference and waterproof performance, is essential.

Based on the above characteristics, the hardware platform of modern marine instrument panels should possess the following features:

High-performance processor: Ensures fast response and accurate display of navigation information, equipped with powerful data processing and graphic rendering capabilities.

Rich Data Interfaces: Integrated with multiple data interfaces such as display ports, serial ports, Ethernet ports, USB ports, etc., enabling seamless connection with various sensors and devices onboard ships for easy data display, real-time acquisition, and transmission.

Reliability Design: The hardware itself demands high quality and stability to ensure long-term reliable operation in harsh maritime environments.

Based on a modern marine instrument screen hardware platform, Forlinx Embedded recommends FET3588J-C as the hardware development solution.

Product Characteristics

High-performance processor: Quad-core 64-bit Cortex-A72 + quad-core Cortex-A55 architecture with integrated 6 TOPS NPU for enhanced AI learning and edge computing capabilities in diverse operational scenarios.

Rich Display Interfaces: Offers multiple interfaces such as HDMI, eDP, DP, MIPI-DSI, supporting various display types including up to 8K output, meeting diverse requirements for maritime instrumentation screens. At the same time, it supports four-screen display function, which enables the crew to monitor multiple important parameters at the same time and improve work efficiency.

High-efficiency Graphics Processing: Integrates ARM Mali-G610 MP4 quad-core GPU, fully compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2, and Vulkan 1.2. Enables maritime instrumentation screens to efficiently handle complex graphic tasks such as real-time rendering and 3D map display, enhancing user operational experience.

Versatile Peripheral Interfaces: Features include dual Gigabit Ethernet, USB 3.1, PCIe 3.0, and 10 UART ports, enhancing data speed and efficiency. This strengthens maritime instrumentation screen functionality, meets navigation needs, and ensures stable data transmission and efficient device communication.

Robust and Reliable Performance: The RK3588J platform meets industrial-grade temperature range standards and has undergone rigorous testing to provide stable performance support for high-end applications. During maritime navigation, stable and reliable instrumentation screens are crucial for ensuring the safety of vessels. FET3588J-C SoM's excellent performance ensures reliable operation of the instrumentation screen in harsh environments, providing accurate data feedback to the crew.

Originally published at www.forlinx.net.

#ForlinxEmbedded #FET3588JC #Rockchip #RK3588 #MarineTechnology #AI #MarineInstrumentPanels #MaritimeSafety #RealtimeMonitoring #HarshEnvironment

0 notes

jcmarchi · 1 year ago

Text

SanDisk Professional Next Generation Storage Solutions for your PROJEC - Videoguys

New Post has been published on https://thedigitalinsider.com/sandisk-professional-next-generation-storage-solutions-for-your-projec-videoguys/

SanDisk Professional Next Generation Storage Solutions for your PROJEC - Videoguys

Explore the revolutionary SanDisk Professional Pro Blade ecosystem, a cost-effective solution that redefines storage expansion. Seamlessly combining SSD NVMe for swift workflows and spinning storage for archiving, backup, and less demanding tasks, this innovative system is perfect for shared environments like Avid or large drive units. The compact and lightweight SanDisk Professional Pro Blade, available in 1, 2, and 4 terabyte configurations, outshines external solutions in reliability and speed. Join us in this video as we dive into the economical and efficient workflow, designed to move data seamlessly from the camera to the edit suite to the archives. Stay ahead in storage with SanDisk Professional Pro Blade – where innovation meets efficiency.

youtube

Special Bundle Offer! Build a PRO-BALDE Workflow Today!

Step 1: Buy a G-RAID Mirror or G-DRIVE Project

Step 2: Add 2 (or more) PRO-BLADE SSD Mags

Step 3: Videoguys will include a FREE PRO-BLADE Transport!

G-DRIVE Project

High-capacity and Fast Data Transfers

7200RPM Ultrastar® Enterprise-class Hard Drive Inside

PRO-BLADE SSD Mag Slot (10Gbps)

Premium Aluminum Enclosure

Adjustable Brightness

Load bearing mounting points

5-Year Limited Warranty

SERIES

G-DRIVE PRO

G-DRIVE PROJECT

Brand

SanDisk Professional

Enclosure

Aluminum

Aluminum and Plastic

Size

8.27 x 5.12 x 1.79 in

8.27 x 5.24 x 3.01 in | 210 x 133 x 51 mm

Weight

2.38 lbs

3.64-3.68lbs

Connectivity

Dual Thunderbolt 3 | Single USB (5Gbps)

Dual Thunderbolt 3 USB-C (USB 10Gbps Compatible)

Interface

Thunderbolt 3 and USB 3.2 Gen 1

Thunderbolt 3 and USB 3.2 Gen 2×1

Internal Hard Drive

Ultrastar® enterprise-class 7200RPM

Up to Transfer Speed (MB/s)

260MB/s Read & Write (20TB)

PRO-BLADE: Up to 1000MB/s Read & Write HDD: Up to 260MB/s Read & Write (18TB & 22TB)

Security Slot

Kensington Security Slot

Compatibility

macOS 10.12+ Windows 10+

macOS 10.15+ Windows 10+ (via reformat)

Features

PRO-BLADE Mag SSD Slot Dimmable LED LightColor-Coded Cables

G-RAID Mirror

High-capacity and Fast Data Transfers

7200RPM Ultrastar® Enterprise-class Hard Drive Inside

PRO-BLADE SSD Mag Slot

Premium Enclosure

Adjustable LED Brightness

Load bearing mounting points

5-Year Limited Warranty

My Book Duo

G-RAID 2

G-RAID MIRROR

Brand

SanDisk Professional

Enclosure

Plastic

Aluminum

Aluminum + Plastic

Enclosure Size

6.3 x 3.94 x 7.09″

8.90 x 11.93 x 6.81″

5.24 x 8.27 x 4.06 in | 133 x 210 x 103 mm

Weight (lbs.)

5.56

6.53

6.75-7.03lbs

Connectivity

1x USB-C (5Gbps)

2x USB-A (5Gbps)

2x TB3 (20Gbps)

1x USB-C (5Gbps)

1x HDMI

2 x TB3 and USB-C Dual-Mode Ports

PRO-BLADE SSD Mag Slot (10Gbps)

Interface

USB 3.1 Gen 1

TB3, separate USB 3.2 Gen 1

Dual mode TB3, USB3.2 Gen 2×1

Speed (RPM)

Ultrastar enterprise-class 7200

Ultrastar Enterprise Class 7200

Transfer Speed (MB/s)

360

500

HDD 260 | Pro-Blade slot 1000

Daisy-Chaining

N/A

Up to 5 devices

Encryption

256-bit AES Hardware Encryption

None

Secure Access

WD Security Password Activation

Kensington Security Slot

Software

WD DiscoveryWD Security (built-in)

None

Compatibility

macOS 11+ Windows 10+

macOS 10.12+Windows 10+

macOS 10.15+ Windows 10+

Warranty

3 Years

5 Years

Others

Dimmable LED light Color-coded cables Hardware RAID control

PRO-BLADE Transport

Powerful: High 20Gbps performance with up to 2000MB/s read and write speeds with USB 3.2 Gen 2×2

Lasting Performance: Adds Thermal management & protection with an aluminum enclosure and heat sink

Built for Pros: Maintain the style, reliability, and durability that customers love

Versatile: Mount to compatible camera rig and only remove PRO-BLADETM SSD mag for easy reloading when USB-CTM recording

USB 3.2 Gen 2×2 20Gbps port: Up to 2000MB/s Thermal Management: Specially designed heat sink to manage the PRO-BLADETM when running at 20Gbps

Thermal Management: Specially designed heat sink to manage the PRO-BLADETM when running at 20Gbps

LED Indicator: Know when it’s connected and when it’s active

PRO-BLADE SSD Mag slot: Keeps the enclosure and fingers cool

Solid aluminum base: Provides durability and style while facilitating heat dissipation

0 notes