#Laboratory and Calibration Lab

[isorajan]

Understanding the ISO 17025 Audit Process in Nepal

Introduction

ISO 17025 accreditation is paramount for testing and calibration laboratories in Nepal to prove their competence and compliance with global standards. A major part of achieving and sustaining this accreditation is going through an ISO 17025 audit. This article is a step-by-step guide through the ISO 17025 audit process in Nepal, explaining each step and why it matters.

What is an ISO 17025 Audit?

An ISO 17025 audit refers to the disciplined verification of technical competency and quality management system of a laboratory. The audit will guarantee whether a lab has the conditions stipulated in the ISO 17025 requirements to perform tests and calibration precisely, reliability, and effectively. By passing the audits, laboratories will be able to earn credibility as well as a good reputation locally and even globally.

Classes of ISO 17025 Audits

There are three general categories of ISO 17025 audits:

Internal Audit: Conducted by the internal laboratory members to test for conformity before the actual audit. This helps identify whether there are any defects or differences that need to be addressed.

External Audit: Conducted by an accredited certification organization to determine fitness for certification. This is the most important step in the process of certification.

Surveillance Audit: Periodic audits conducted after certification to ensure continued compliance. Laboratories must undergo such audits from time to time to maintain their certification status.

ISO 17025 Audit Process Steps

Step 1: Pre-Audit Preparation

Before the actual audit, laboratories must:

Conduct a gap analysis to identify areas of improvement.

Review and update their quality management system (QMS).

Train staff on ISO 17025 compliance requirements.

Keep equipment in good calibration and maintenance.

Arrange all records and documents regarding the audit so that they may be easily located at the time of the audit.

Step 2: Internal Audit

Self-assessment calls for internal audit. Some important points are as follows:

Contrasting procedures and documents with requirements for compliance.

Performing test samples for the verification of accuracy and reliability.

Detecting non-conformity and taking rectification measures.

Creating comprehensive internal audit reports, which may be reviewed by the management and be used for the improvement of the process.

Step 3: Management Review

Management review involves review of internal audit results and follow-up for the follow-through on correction of weaknesses. By this step, the following are guaranteed:

Assurance of ongoing improvement.

Commitment of resources towards improvement of weaknesses.

Preparation for the external audit.

By the formal review process, the laboratories are encouraged to tackle any anticipated challenges even before a formal certification audit can be conducted.

Step 4: External Audit by Accreditation Body

Official audit ISO 17025 is done by an accrediting agency and involves:

Document Review: A review of procedures, policies, and records maintained by the laboratory.

On-Site Assessment: A visitation of staff capability, equipment, and facilities.

Test Witnessing: Observation of the laboratory employees performing tests in order to find out if standard operating procedures are followed.

Interviews: Interviews with personnel in order to understand their familiarity with and application of ISO 17025 requirements.

The external audit may be undertaken in a matter of days depending on the laboratory size and complexity.

Step 5: Non-Conformity Identification and Corrective Action

Where non-conformities are identified during audit, the laboratory must:

Remedy the issues within a certain time frame.

Provide documented evidence of corrective action.

Be re-audited where required.

Non-conformities, where not resolved, can delay or even prevent certification, and laboratories must therefore move fast in instituting corrective actions.

Step 6: Certification Decision

When the external audit is successfully completed, accreditation is issued by the accreditation body with ISO 17025 certification. The laboratory is officially recognized for following international standards. This certification gives more credibility to the laboratory and enables them to issue internationally accepted test reports.

Maintaining ISO 17025 Compliance

ISO 17025 certification is not a one-time event; laboratories have to:

Perform routine internal audits for continued compliance.

Conduct regular surveillance audits by the accrediting agency.

Update procedures to include new developments and innovations in the field.

Provide employee training continuously to remain in compliance.

Have a formal quality management system with continuous improvement being promoted.

Non-compliance will result in suspension or revocation of certification and, as such, laboratories must keep themselves on their toes.

5. Challenges Typical of Audit Process

Nepal laboratories may face issues such as:

Lack of Awareness: Absence of ISO 17025 requirements awareness among laboratory staff.

Resource Constraints: Inadequacy of training budgets, equipment replacement budgets, and documentation improvement budgets.

Staff Competency Issues: Ongoing employee development is essential as a result of evolving industry requirements.

Technical Non-Conformities: Failure to retain traceable and correct calibration records.

Infrastructure Limitations: Some of the laboratories may need infrastructural improvements to meet ISO 17025 compliance.

To overcome these challenges, laboratories need to invest in training, seek external expertise when necessary, and have a culture of constant improvement.

Benefits of ISO 17025 Audits

ISO 17025 audits benefit laboratories in Nepal in many ways, including:

More accurate and reliable test results.

Increased credibility and acceptability in the local and international markets.

Increased customer confidence and trust in laboratory services.

Enhanced risk management and identification of likely process vulnerabilities.

Better adherence to regulatory guidelines and industry standards.

Conclusion

The ISO 17025 audit is a requirement for laboratory effectiveness, accuracy, and international acceptability. The Nepal laboratories, with a step-by-step strategy, can obtain and maintain ISO 17025 certification easily, enhancing their credibility and business excellence. Regular audits, continuous improvement, and employee training are the secrets to long-term success and compliance. Laboratories that put high importance on ISO 17025 compliance not only improve the quality of their work but also become a market leader.

Visit https://qms.com.np/ to learn more about ISO.

[tremendousbluebirdtidalwave]

How to Choose the Right Laboratory Equipment Manufacturer in Hyderabad

When setting up or upgrading a laboratory, choosing the right laboratory equipment manufacturer is a decision that can impact your operations, accuracy, safety, and compliance. Whether you're a research institution, educational center, or industry lab in Hyderabad, selecting a reliable partner ensures you receive high-quality, certified, and efficient equipment for labs that meet your specific requirements.

So, how do you pick the right manufacturer among the many lab equipment suppliers in Hyderabad?

Evaluate Product Range and Specialization

Look for a manufacturer who offers a comprehensive range of scientific equipment, from basic tools like beakers and microscopes to advanced testing and calibration instruments. If you need specialized items — like agricultural equipment or water testing kits — confirm that they have domain expertise.

Example: Lavaasa Scientific offers equipment across sectors: education, R&D, water, soil, food, and agriculture testing.

Ensure ISO Certification and Industry Standards A trustworthy manufacturer adheres to ISO standards and provides CE-certified or BIS-compliant products. Certifications ensure safety, accuracy, and quality, which are crucial for scientific equipments.

Ask About AMC, Calibration, and After-Sales Support Choosing a manufacturer isn't just about buying — it's about maintaining. The right supplier will offer:

Annual Maintenance Contracts (AMCs)

Installation & Calibration Services

On-site Repair & Replacement

This ensures long-term reliability and reduces operational downtime.

Consider Local Presence and Delivery Capability Working with a local lab equipment manufacturer in Hyderabad reduces logistics time, shipping costs, and service delays. You can also inspect the products personally before making bulk purchases.Local vendors like Lavaasa ensure quick delivery across Telangana and Andhra Pradesh.

Read Reviews and Ask for Client References What are others saying? Read testimonials, reviews, and ask for references from research institutes, colleges, or industries they’ve served. Genuine reviews can speak volumes about product durability and service consistency.

Customization & Bulk Order Handling If you require modified designs or bulk lab kits for institutions, check whether the manufacturer can custom-build instruments or provide combo offers for lab equipment supply.

Compare Pricing and Warranty TermsDon't just go for the lowest price.

Product quality

Warranty period

Installation support

Spares availability

A slightly higher cost with better service is often a smarter long-term investment.

🏢 Need Help Choosing? Contact Lavaasa Scientific As a leading laboratory equipment manufacturer in Hyderabad, Lavaasa Scientific is known for:

ISO-certified lab and agricultural equipment

Calibration and AMC services

Custom solutions and fast local support

Trusted by institutions across South India

📞 Call: +91-8826423285 🌐 Website: lavaasascientific.com 📧 Email: info@lavaasascientific.com

🧾 Conclusion Choosing the right lab equipment supplier in Hyderabad isn’t just about products — it’s about partnering with a team that understands your lab's goals. Focus on quality, service, compliance, and local presence to ensure you get the best value and long-term performance.

[yashshreeseosworld]

IEC 60601 Testing Labs for electrionics and medical device testing.

An NABL-accredited lab specializing in electronics and medical device testing, ensuring IEC 60601-1 compliance for the safety and performance of medical equipment.

[acutedigital]

NABL approved Labs in India Your Product Safety Partner

Astute is a top testing company in Pune, specializing in medical device testing. We offer reliable and accredited testing services to ensure product safety and compliance.

[labnicsltd]

Calibration Weight Set NCWS-100

Labnics calibration weight set has 27 pieces of weights to ensure durability and resistance to environmental factors. it has density of 7.96kg/dm³ with non-magnetic stainless steel and it features protective aluminium case with easily transportable.

[thetnclab]

Calibration Lab Delhi

TNC Lab is a premier Calibration Lab based in Delhi, specializing in precision instrument calibration services. With state-of-the-art facilities and a team of highly skilled technicians, TNC Lab ensures the accuracy and reliability of a diverse range of instruments across various industries. Committed to quality and precision, the lab adheres to international standards, providing clients in Delhi with meticulous calibration services to enhance the performance and longevity of their instruments. TNC Lab's expertise and dedication make it a trusted partner for businesses seeking precision and compliance in calibration within the bustling metropolis of Delhi.

Read more:-

[raiconsposts]

When it comes to ensuring the accuracy and reliability of your equipment, finding a trustworthy calibration service provider is of utmost importance. Our Calibration Labs in Delhi are your one-stop solution for all your calibration needs. We take pride in offering exceptional calibration services that guarantee your instruments perform at their best. Website URL :- https://raiconlabs.com/calibration.html

[supercap2319]

Reed fumbles with a device, looking befuddled, while Johnny tries to help, playing it cool. "Ah, come on, Reed, it's not that hard! You just need to..." Reed looks up, aghast, as Johnny accidentally causes the device to malfunctions. It sparks as Y/N walked into Reed's lab.

With a heavy sigh, Reed, running a hand through his hair as he picks up, and examines the damaged device. "Great, just great." Johnny looks sheepish, shrugging apologetically. "I was just trying to help, okay?" Reed shoots him a disapproving glare. "Help? You call that helping?"

"It was an accident, Reed. Don't be so uptight." Johnny said.

"Uptight? You think I'm being uptight?" Reed asked. "Do you have any idea how long it took me to calibrate this thing?"

"What was it supposed to do?" Y/N asked, making his presence known in the laboratory. Reed sighs, setting the device down. "It was supposed to be a new prototype for the force field generator. But now..."He gestures to the broken device. "Now, it's just a pile of useless parts." Johnny plops down on the nearby couch, looking unimpressed.

"Johnny? Don't you have something you wanna say?" Y/N asked.

Johnny grins mischievously, leaning forward. "Oh, I've got plenty to say." He looks at Reed, then back at Y/N. "You know Reed's gonna be sulking for weeks now, right?"

"Well, why wouldn't he be? He worked hard on that device. How would you feel if you were working on your 2004 Mercedes-Benz SLR McLaren C199, and I just went in and messed up the motor or something?"

The blonde laughs, standing up from the couch. "Oh, please. Like you even know how to work on a car, Y/N." He walks over to the broken device, picking it up and examining it. "Besides, it's not like Reed can't just build another one."

"That's not the point, Johnny. The point is that you need to apologize. And screw you. I do know about cars. Y/N said.

Reed watches the exchange with a mix of amusement and frustration, arms crossed. Johnny drops the device on the table, turning to face Y/N with mock seriousness. "Oh, yeah? Prove it." He grins playfully. "If you can fix a car down in the garage, I'll apologize to Reed. Hell, I'll even help him work on it."

"Fine. I will. Show me to the car. And the wrench. And that thing you use to take off the bolts on the tire of the car." Y/N said. Johnny chuckles, leading Y/N towards the garage with a smug grin. "Right this way, gearhead. Try not to get grease on your hands—unless you're into that sort of thing." Reed follows reluctantly, shaking his head.

[under0-0s]

200th Park Avenue, Midtown Manhattan, New York City. 02:43:27 A.M - Laboratory Room. ____________________ (listen to the music to improve the reading experience.)

_____________________

Tony Stark had always thrived in chaos, but this was different. This was a kind of entropy that clung to his bones, settled into his lungs, and refused to let go. Seventeen days and fifty-two hours—long enough for the world outside to twist into something unrecognizable. The weapons division was back, and so was the backlash. The media called him a war profiteer, a fallen hero, a traitor to his own ideals. The ring from a certain someone, that once held promises now lay forgotten in some drawer, and Serena’s voice still echoed in his mind, raw with anguish. Hunter was out there, bullet chambered, mark set.

It didn’t matter.

What mattered was here, now, in the icy stillness of his lab. He’d shut out the noise, ignored the ghosts that clawed at his conscience. Instead, he stared into the heart of something unknown.

A transparent, human-sized chamber stood at the center of the room, its neon-lined edges casting eerie reflections on the steel walls. Inside, a rippling void hovered—a bright streak, like lightning frozen in time, a tear between dimensions. The air buzzed with energy, a whisper of something just beyond reach. He had calibrated every parameter to the most precise degree, pushing past theoretical impossibilities.

This wasn’t about weapons, not really. It wasn’t about escape, either. It was about the spark. The one thing that had eluded him in everything else.

“Sir, I must remind you that exposure to the anomaly beyond its current containment field presents a high probability of destabilization.”

J.A.R.V.I.S.’s voice, crisp and composed, broke through the quiet hum of machinery. The AI had been monitoring the experiment with unwavering precision, cataloging every fluctuation, every surge of energy, every anomaly.

Tony exhaled sharply, rubbing a hand over his face. “Noted, J. But if I don’t push this further, I’ll never know what’s on the other side.”

“There is a fine line between discovery and destruction, sir.”

A wry smile ghosted across Tony’s lips. “Yeah, well. I’ve never been much for fine lines.”

J.A.R.V.I.S. hesitated, as if calculating the odds of Tony actually listening to reason.

“Would you like me to prepare emergency protocols in case of—”

“No.” Tony cut him off. “We’re not failing today.”

He adjusted the temperature again, a frigid cold settling into the room. His breath ghosted in front of him, cheeks pinkening from the artificial winter. He didn’t move. He barely blinked. He only stared, waiting, hoping, needing something to break through the weight of failure that had consumed him for far too long.

And then—it happened.

The spark.

Small, fleeting, yet infinite in its implications. A shimmer that pulsed through the tear in space, dancing along the edges of the anomaly, illuminating the abyss with an unearthly glow. Maybe it was just a reaction. Maybe it was nothing at all. But for the first time in days, something worked.

His fingers twitched, as if reaching for it, for the proof that something still remained. Something untouched by betrayal, by war, by loss. Maybe it was just physics. Maybe it was just a trick of the mind.

Or maybe—just maybe—it was the proof that between every rupture, every break, every tear, there was a space where something new could exist.

And so he stared, unblinking, as the dimensions split just long enough to let the spark linger.

Because maybe—just maybe—there was still something left to salvage.

The air around him hummed as the neon streak pulsed once more, sending out thin tendrils of energy that wove through the air like living things. He exhaled slowly, eyes narrowing as he adjusted the stabilization settings on the console beside him. If he could just hold the split open long enough, he might be able to measure the properties of whatever existed within. Maybe even step inside.

The thought was reckless, but he had always lived on the edge of recklessness and genius. There was no denying the pull he felt—no denying the possibility that on the other side of that tear, something awaited. Something better. Something more.

But there were risks.

The algorithms were still incomplete, the equations still not fully understood. The chamber’s integrity was holding, but for how long? And if he lost control, what would happen to the lab? To the world?

“J.A.R.V.I.S., run a full diagnostic on the containment field.”

“Processing,”

The AI responded smoothly.

“Energy stabilization at 84%. Containment holding, but fluctuations increasing by 0.7% per second.”

Tony frowned. That wasn’t great. He had minutes at best.

He should stop. He should shut it down and walk away.

But he couldn’t.

Because for all the ways he had failed, for all the people he had let down, for all the things that had slipped through his fingers—this, this, was still in his grasp.

He clenched his fists, jaw tightening as the cold seeped deeper into his skin. The glowing fissure flickered, almost as if it, too, were waiting.

He stepped closer, the hum growing louder. The streak of light stretched and curled, forming delicate arcs that shimmered against the steel walls. His pulse quickened. He reached out, fingers hovering just inches from the anomaly, the energy tingling at his skin.

“Sir, I must reiterate—”

“J, shut up.”

The lab was silent, save for the faint vibrations of the machinery. No voices. No outside distractions. Just him, standing at the precipice of discovery—or destruction.

He took another step forward, heart pounding in his chest. The anomaly pulsed, its radiance fluctuating like the heartbeat of something alive. If he crossed the threshold, if he reached into the unknown, would he find answers? Or only more questions?

The machine hummed one last time before he exhaled and stepped back. He reached for the console, fingers hesitating over the shutdown sequence.

Then, with a final glance at the spark still flickering within the anomaly, he pressed the button.

The energy curled inward, collapsing in on itself until all that remained was the cold and the silence.

J.A.R.V.I.S. spoke first.

“Experiment concluded. Data has been logged.”

Tony turned away from the empty space, running a hand down his face.

Seventeen days and fifty-two hours. That’s how long he had been waiting for something to go right.

The weight in his chest shifted, just a little.

Maybe there was still time to make something of it.

_______________

( Tags so that this just doesn't die: @oh-to-be-a-murderer @the1-and-only-peggycarter @crazyinlovewithmarvel @thatone-midgardian @over-bi-the-wayside @its-nate-the-sharpshot @multiverse-peterbparker @clintbarton-thearrowguy @spidey-sensed-ur-follow @lunamarvels @insomniac-lifestyle @playgirlgenius @the-iron-rose @little-lost-prince )

[karinweek]

KARIN FANS!!!

We had a poll asking what day of Karin Week people are most excited for. Second place was June 19 (Temptation | Laboratory | Partners in Crime)! So........

Tell us what you think Karin's lab activities are like!

Never heard of Karin Week? In 2025 it will run June 14-20 right here on @karinweek to celebrate all things Karin. Follow us & check out our FAQs, rules, and AO3 collection. Also check out our official prompts post to see what's happening other days!

[hotheadedhero]

In Unrequited Love

Love and relationships can't be forced but sometimes they can be built on common ground and an understanding of one another's tribulations.

Part 2 here

Donatello x Reader

Having a crush on someone sucks. Having a crush on someone who has eyes for someone else sucks even more. This is the sad truth of your current circumstances. You knew that high school would come with its challenges but you weren’t prepared for the fact that you’d fall for the careless, hockey-loving maniac from your math class. It began with a casual friendship before feelings deepened on your end. Feelings that wouldn’t seem so terrible were it not for April O’Neil. You have absolutely nothing against the girl but it’s clear as day that she unfortunately has Casey’s heart in her stronghold. It’s not like you could even vent these frustrations, given that the only friends you have happen to be those two people. 

Then, through some shenanigans that seem like the norm for you now, you meet four turtle brothers - one of whom is in the same boat as you. Not to mention, between the very two friends in question. Were it not heartbreaking to witness each other trying your hardest to grab the attention of your crushes, you’d find some humour in this.

You tried hanging out with Raphael more in an attempt to get in close quarters with Casey, seeing as they’re practically tied at the hip, only for you to realise that the rough-and-tumble environment isn’t your strong suit. That’s when they both suggested you try your hand at assisting Donatello in his laboratory given your aptitude for the sciences. What they failed to realise is that you do well in class but that doesn’t inherently mean you enjoy it. Theoretical sciences and learning about how things work are interesting but there aren’t enough practical applications that allow you to engage in the school environment. The closest you’ve gotten to having fun was when you made “elephant toothpaste” for a chemistry lesson but that’s about it. 

Nonetheless, you see no harm in passing by the lab and giving the brainiac brothers a visit. Other than your not-so-subtle pining towards the other humans in the group, nothing has been outwardly mentioned about the situation you are both in. Neither of you has hung out enough to have that conversation. It wouldn’t be weird to talk about it, would it? A query that shall not yet receive an answer seeing as you’ve already knocked on the large, metal door. You walk through the open garage to see a couple of legs poking out from under the battle shell. 

“Huh? Oh! Y/n, sorry- Ow!” He slides out from beneath the vehicle and rubs the fresh bruise forming on his head. “Sorry, I’m a little busy, right now. I think Leo is watching Space Heroes if you’re looking for someone to hang out with, though.”

“Actually, I came by to see if you needed any help,” you offer, holding your hands behind your back respectfully whilst also trying not to laugh. 

His eyes widen, having not expected such a proposal, and he’s quick to scramble to his feet.  “Oh, okay! Let’s see- uh… how are you with engine repairs?”

“Depends.” Your tongue clicks contemplatively. “Is it gas, electric, or hybrid?”

“That already tells me you know more than enough,” he chuckles. “Here, I’ll show you.”

He opens the hood of the van to reveal the ensemble of burnt-out parts and overworked mechanisms. The guys’ last mission must have been intense because this engine is almost in complete disarray. Were it not for the fact that your Uncle is a mechanic, you’d be sweating under the pressure of somehow ruining this heap of metal more than it already is. A probability still if you want to jinx your person but that’s getting ahead of yourself. 

Donatello gestures towards a box of spare parts and holds the back of his neck. “These just need to be taken out and replaced. It’s probably the easiest of what needs doing but I also need to finish rewiring the brakes, check the throttle calibration, replenish the weapons ammunition-”

“You need an extra set of hands to get it done quicker,” you cut him off with a smile. “I’ll see what I can do.” 

He bares a gap-toothed smile in response and nods before resuming his initial position beneath the vehicle to finish the brake wiring. This leaves you to begin on your assigned job. For starters, you’re glad that this is a case of piecemeal repair rather than a complete engine rebuild. You’d be out of your depth were that the case. You start by pulling the entire engine out via a hoist, assisted by a load levelling bar so that it doesn’t tilt at a funny angle. Then, you secure it onto a stand and glance over what you’re working with. The crankshaft, piston ring compressor, oil filter, and fan need the most attention, so you start with those first. Just to save the disturbance, you look into a few tutorials on your phone to make sure you’re doing it correctly. 

During this entire time, the two of you work on separate parts of the battle shell in silence, seemingly content with your tasks. By now, Donnie has moved on to tightening the wheels’ lug holes. Admittedly, you had been concerned about a lack of things to talk about but this is a nice settlement. It’s certainly the most relaxed you’ve felt in a while; something to keep you distracted from the quelling of your hopeless romantic attraction. Plus, you have this sense of relief from finally being able to work on something with your hands rather than straining your brain over textbooks and pop quizzes.

"Question,” he starts abruptly, keeping his eyes on the centre cap of the wheel. “What’s it you like so much about that cave mouth?"

First, you blink quickly to yourself, having not expected to get into the nitty gritty of it so soon. So much for being distracted but you can’t be mad. Curiosity isn’t something to be berated. Then, you find yourself snickering at the mildly degrading nickname. The question may appear brash but he’s puzzled by why April seems to like Casey so much. Hearing it from you might give him the insight he needs to turn the odds in his favour. He’ll take anything at this point. 

"I dunno. There's just this air to him that I like. He's an ass, I am well aware of that, but he's fun, you know?” you admit awkwardly. “Psh! Don't ask me to explain it. You can't really put that stuff into words." You squint down at him, lips poised mockingly. "What is it you like about April so much?"

He halts his own task and glances down at his hands, cheeks reddening as he thinks about the girl of his dreams. "She just... had my heart from the first moment I saw her."

"Wow. The first girl you ever see in your life and it's just like that.” Yes, that bit of information is known thanks to our dear Raphael. “'Pretty shallow to fall in love with someone based on looks if you ask me." 

"You would know,” he scoffs sarcastically.

"Now you're calling Casey ugly?” you ask, both playful and moderately offended on your crush’s behalf. “Man, you really don't like him."

"I’m sure the same goes for you with April!"

"Hey! I don't stoop so low into my dissatisfaction of the circumstances to insult her." A wry grin then beckons your lips. "Although~"

"Whatever you think you're going to say, don't."

The staring match doesn't last long, breaking beneath a shared laugh; fond and unwilted by the ache in your hearts, which has been forgotten for a split moment to enjoy each other's company.

From that point on, that’s precisely what you did. More often than not, you found yourself in the confines of his garage, assisting him with the occasional doohickey and thingymabob. Even if there wasn’t much you could help with, you wound up being a decent lab partner in any case. In turn, he would offer to help you with your homework if you had any particularly difficult assignments. Your grades have never looked so good. When neither of you were doing that, you’d simply hang out and rant about little annoyances with your unreciprocated infatuations. 

“I mean, I try some jokes here and there but nothing seems to land,” he concedes begrudgingly, throwing his body weight into the back of his chair.

��Can I hear one?” you inquire as you gently swing around in your own seat. 

His lips press together and he mulls it over before sighing, “Okay, so, you remember how I told you about Metal Head?” You nod, to which he continues, “Well, the first time I took him out for a spin, we were on watch duty together. That’s when I asked her if she likes metal.”

He groans to himself as he replays the memory in his head, only now realising how corny that must have sounded at the time. However, you laugh and not the heckling kind either. Your head tilts back into your chair, knees lifting to compensate for the tension in your shaking stomach. How could April have not loved something as precious as that? The girl must be crazy because that would have worked on you in a heartbeat. 

“You should’ve asked if her favourite dance move is the robot,” you say in between laughs. “No, wait, wait! I got a better one! Ask her out to the circuits for a date!”

Donatello can only smile at your self-induced amusement, happy that there’s an appreciation for nerdy pickup lines and puns. They may not work on his crush - and his brothers sure don’t find them that funny - but he’s glad at least one person around here gets it. 

It felt good to know that you had a friend you could be closer to because of your mutual understanding. For the first time since you realised your feelings for your schoolmate, you didn’t feel so alone. This bond formed on cluttered affection may have seemed unlikely to begin with but who are you to complain now? You and Donnie have a good thing going given your positions. 

That is until your heart diverts its attention towards the very turtle. 

You came to the realisation when he expressed his excitement in showing you his newest invention. The fact that he had called upon you first made you feel special. It made you feel wanted and desired for the first time in your life. A seemingly small phenomenon given how he merely wanted to showcase something to you but the way it had tugged your heart was unparalleled to anything else you had ever experienced - and that smile. You could have happily fawned over that proud grin of proclaimed accomplishment and self-justified pride for the rest of that day. Then, it all came crashing down on you like heaps of scrap in a junkyard. You have fallen for someone who is in love with April. Again. Are you just doomed to fall for any man that crushes this girl? This must be some sick joke. One that you don’t find yourself laughing at. 

It eats away at you for the days - weeks - to come. You can’t console anyone on the matter, either. If any of his family catches wind, there’s a chance of him finding out. An outcome you wish to avoid if possible. As for Casey and April, dear lord you don’t even want to know what would happen if you told them. You’re at square one again just as before: crushing on someone who will never feel the same way about you. Rotting in a pool of your self-made disillusion.

Alone.

Having a crush on someone sucks.

[acutedigital]

Astute Lab: Biomedical Equipment Calibration for Hospitals

Astute Lab provides expert biomedical equipment calibration for hospitals, ensuring precision and safety. As a NABL approved Labs in India, we deliver reliable and accredited services.

[stoicconfluxvow]

The Yin and Yang of Engineering: Jinx/Viktor

Chap. 1: Tinkering with the absurd.

The scent of scorching metal and candle wax lingered in the air, mingling with the residual ozone of active Hextech. The laboratory existing as an ecosystem of its own — a microcosm of calculated order, in which every movement was rigorously orchestrated, every instrument meticulously placed, every breath synchronized to the steady hum of interconnected machinery. The crisp scratch of graphite against parchment, the measured clink of tools — the usual praxis. Something, however, had already begun to disrupt its equilibrium.

Viktor sensed the disturbance before he saw it. A minute displacement in the air pressure, a fractional shift in the ambient acoustics; the subtlest irregularity. Then, the faintest creak from above.

He let his fingers continue their measured course along the Hextech circuitry before him, grip steady, focus ostensibly unscathed. A test, in part—to see how long the anomaly would linger before announcing itself.

He had already detected the pair of pendulous blue braids dangling into his peripheral vision; had already cataloged mass, velocity, and descent trajectories should the anomaly, as anomalies often do, spiral into a paroxysm of unpredictability.

"You look very ugly from this angle, y'know?" came the snickering, upside-down voice. The words were laced with a gummy, lopsided grin.

Viktor let out a stolid, measured exhale, slowly tipping his head up. “And you resemble a bat.” he replied evenly, tone as measured as his calibrations.

The statement elicited a gnarly laugh from Jinx, who was suspended from an overhead beam. Her entire body was folded into an improbable pose, legs hooked over the steel girder as though gravity were merely a suggestion.

The neon glow of Zaun’s skyline bled in through the lab windows, casting fragmented light over the contours of her rounded features, the faint smudge of soot dusting her jawline, the subtle asymmetry of her pupils—one slightly more dilated than the other. A tell, perhaps.

Viktor merely adjusted a stabilizer. “Should I begin to question how you got up there?”

Jinx twisted midair with a surprising economy of movement. The vertebral rotation was precise, controlled—almost acrobatic.

Then, without warning, she let go. Viktor tensed, a reflexive tightening of his grip on the edge of the workbench. The poor scientist had already begun to map trajectories, force differentials, probabilities of injury, only for the jinx to land in a perfect crouch, one hand brushing the floor for balance before springing up with the fluidity of a creature built for unpredictability.

Jinx twirled once, for no discernible reason other than self-amusement, then flopped onto one of his worktables, her limbs sprawling on the surface with careless abandon.

“So, Doc?” Jinx drawled, tilting her head toward the intricate lattice of Hextech components strewn before him. “whatcha cooking up in that fancy contraption of yours?”

"A minor enhancement,” he answered, gesturing at the faintly pulsating gemstone embedded in the device. “One that may stabilize Hextech output during large power draws. We—” he hesitated, momentarily considering whether to lump himself in with Piltover’s more refined approach "—some of us forget how violent these energies can be when not properly harnessed.”

“Violent energies, violent minds,” she mused, referring to his earlier statement, while patting down the dust on her patchwork trousers. “Nothing a little disorder can't fix.”

“Entropy requires boundaries,” Viktor corrected, keeping his voice gentle despite the admonition. “A container. Else it consumes itself and everything around it.”

"Alright, philosopher," she snickered, "so, what you're telling me is 'no boom'?"

“Absolutely not. No utility whatsoever in explosions."

Jinx's ebullient expression dropped to a saturnine one. “Boring,” she huffed, scrunching her nose. “why are you like this?”

“Functionality,” Viktor returned evenly, “is not contingent on spectacle.”

“Roger that.” she sneered. Jinx twisted at the waist, swinging gently like a pendulum.

She peered at him through the electric haze, turning a small metal sphere over in her hand—one of her bombs, he surmised, judging by the labyrinth of tiny, improvised coils etched along its surface. It was disarmingly compact, unpolished, but brimming with haphazard brilliance. There was artistry in its asymmetry, like a half-remembered blueprint from a dream.

She pressed the sphere into his palm. “Try to make this stable now, yeah?” her tone brimming with the same sardonic twang she always carried. Yet beneath that, a flicker of sincerity: an invitation to test the boundaries she had set.

Viktor’s metal brace squeaked softly as he shifted his weight, accepting the device with steady composure, analyzing the craft with composed fascination. “I am usually up for a challenge,” he replied, a faint thread of wry humor lacing his tone. “However… I must insist you not hang from my rafters again without warning. The structural integrity—”

“Yeah, yeah," she immediately interrupted him, snorting, "... deal."

Viktor set the bomb gently on the worktable and glanced at her. In the silent seconds that followed, there was no condescending tut-tut of a Piltover academic, no sanctimonious lecture of what she could have done better. Merely an unspoken accord that if they could each appreciate the other’s mania—and keep its calamitous potential in check—there was something worth building there.

He adjusted a delicate filament, the faintest suggestion of amusement sparking behind his amber eyes. “You mistake methodology for rigidity,” he randomly mused, glancing sidelong at Jinx.

Her nose wrinkled again, waiting for him to elaborate.

He rolled his wrist as he set a filament connector. “A scientist does not calculate every step merely to banish unpredictability. Calculation is comprehension—to understand a system so deeply that you know precisely where to push and when to pull. Not to prevent chaos,” he added, letting the final phrase hang, “but to direct it.”

Her lids flickered in hesitant acknowledgment; skepticism warred with fascination in her mismatched gaze. “So what you’re saying,” she pressed, “is that you do like messing with things, you quaint, boring guy.”

A soft hum escaped Viktor’s throat, ignoring the insults. “The core of invention is not the mere desire for control, but curiosity,” he continued. “The difference,” he said mildly, “is that I prefer my experiments remain intact by the end of it.”

She slid off the table and prowled around the lab, trailing her fingers over metal and wire, rifling through blueprints.

Jinx moved like she thought in tangents: erratic. Nonlinear. Pausing here, skipping entire sections there, only to circle back if something caught her eye again, in what one could call a stochastic, staccato fashion.

Viktor, wisely, did not intervene. He had long since learned that when it came to Jinx, indirect engagement was often a more effective deterrent than forbiddance.

Eventually, she plopped herself down at a workbench—one cluttered with Viktor and Jayce’s shared diagrams—scrunching them aside with a careless sweep of her forearm. Surprisingly, she took pains not to knock them to the floor or tear them. An almost incongruous note of consideration from someone so prone to what Viktor could only describe as deliberate rascality.

Jinx stretched until a series of pops echoed through the quiet workshop, then rummaged in her satchel. Out came the neon-splashed paraphernalia she called her toolkit: coil springs, nuts and bolts of questionable origin, and—of course—her beloved spray cans in garish, candy-colored hues. The stark contrast against Viktor’s methodical array of polished metal components was almost comical.

Yet neither commented on it. Viktor, engrossed in refining a fractal array for stabilizing Hextech surges, offered only the occasional sideward glance. Jinx, with her usual lack of ceremony, fished out a crude welding torch and got to work assembling... something. If the shape seemed headed toward destructive potential, Viktor refrained from remark—he had long discovered that sharing space with her was a delicate dance better navigated by trusting in her ad-hoc, if not entirely safe, sense of boundaries.

Hours passed in near silence. In place of conversation was the rhythmic hum of the lab, the hiss of flux as Viktor soldered circuit boards, the faint crackle of Jinx’s blowtorch. Occasionally, Jinx broke the hush with a sudden whoop or guttural holler, purely to see Viktor jump at the unexpected noise. Each time, she dissolved into snickering laughter. He responded with measured exasperation, arching one brow but saying nothing. Even so, a trace of bemusement flickered across his features, as though he found her antics strangely disarming.

Eventually, the overhead lamps dimmed, a subtle reminder that the hour was growing late. Viktor powered down his apparatus with a final flip of a switch. Jinx, yawning in an exaggerated manner, began stowing her things in a scuffed leather pouch. "Think 'm headin' out now. Night night."

"Night."

The woman had already crept back up with the grace of a nimble rat, scaling the ceiling pipes, her long electric blue braids once more dangling upon Viktor's forehead as he scarcely managed to push them aside. She then made her way to the same improbable entryway through which she had crashed into the lab, quietly humming an off-key tune before vanishing into the sooty shadows beyond.

Viktor, by contrast, had continued his work undisturbed, denying himself even the basic luxury of sleep. When his eyelids finally began to grow heavy and he awoke from a brief micro-slumber, elbows unceremoniously propped on the workbench, he caught, in a dazed haze, the blurred image of a bizarre object with distinct animalistic contours, stationed before him as though it were unnervingly staring at him.

Instinctively, he flinched, covering his head as if to brace himself for the expected detonation which, surprisingly, never came.

The odd bitzer remained still, with no sign of malevolent nature, glimmering quietly under the workshop’s neon gloom — a squat, mechanical monkey-like figure sporting metallic plating with a grotesque smile and an odd coil in its belly.

Viktor raised a brow as he took note of the small sprig attached to its left hand, that held the monkey's weight into an erect position while seemingly mimicking the scientist's own ligneous cane. His attention was then captured by the bright yellow post-it affixed to the metallic ape with a messy bit of tape, scribbled in a deliberately sloppy handwriting:

“name's cookie... he looks like you. yuo can keep it :o)

– J”

Beneath it, a wonky smiley face scrawled in lurid neon ink, as asymmetrical as its creator’s grin.

It elicited a smile from him, who examined it as it rested upon his palm. Albeit a bit rough in its form, the artefact appeared to be crafted with a certain intent, perhaps even care. He pressed a button to test the mechanism, still half-expecting an explosive cacophony. The monkey’s tiny arms flailed in a spasmodic dance, beginning to tremble as if preceding detonation, only to splutter out a few confetti which landed on his ivory jacket. Viktor shook his head, his expression softening to one of amusement.

He let his index carefully trail over its metal plating, before placing it on his workbench beside the half-finished stabilizer, the neon-paint smudges glaring against the refined Hextech casing. For all the incongruity, there was something undeniably… charming about it. Perhaps endearing even. He'd later hang it up in a corner of the lab, a testament to the newfound, improbable synergy.

For the first time since Jayce's abandonment of the lab in pursuit of his councilor duties, Viktor perceived a vague sense of vacancy following the disappearance of Jinx and her shenaningans, which alongside his exhaustion finally prompted him to call it a day and go home, an unfortunately rare occurrence for the inventor.

In truth, this measured respect and fascination had begun well before Jinx’s impromptu acrobatics in Viktor’s laboratory — it had taken root, ironically, in moments where they’d never even met face-to-face.

Viktor recalled being urgently presented with the disarrayed collection of fuliginous, hazardous mechanical constructs—agglomerations of metallic scraps, remnants of gunpowder cartridges, and nearly comical embellishments of dubious taste, alarmingly rumored to have derived from Silco's inner circle.

"The configuration is... rough, though there certainly is a certain knowledge of engineering, if not mere intuition." Viktor mused, carefully examining the device's labyrinthine wiring and ingeniously modified spark fuses of the complex apparatus beneath him.

"Would they be capable of figuring Hextech out?" Jayce wondered aloud, his steps resonating an anxious rhythm across the chamber's floor.

"Eh," Viktor hummed pensively, "I wouldn't exclude it. The possibility does exist."

"With a complete lack of the theoretical basis? No, no. Years of research and tests only for some... sick, delinquent mind to comprehend and emulate so effortlessly? No chance." he quickly retorted, the firm incredulity in his voice coming across as an attempt at self-regulation rather than genuine conviction. "This is merely a... well-thought attempt at scare tactics. To intimidate us into allowing independency."

"The absence of formal theory, or proper equipment, only serves to underscore the inventive potential of such mechanical artistry." Viktor countered, "If only such acumen could be channeled towards something more... constructive." he then mused, lithe fingers delicately twiddling with the disassembled filaments beneath him.

"Potential? Viktor, this is sheer madness. These are seeds of entropy threatening to contaminate the flourishing utopia that is Piltover. I can not tolerate nor allow this, and may be obliged to..." he paused, simultaneously recalling Medarda's words and anticipating the partner's disapproval, "take countermeasures."

The statement did, in fact, earn a mild glare from Viktor, who was intently scanning the device's subversive wiring.

"If I recall correctly, weren't Hexgems, too, violently volatile in their raw form?" Viktor extended his arm, the servos in his brace whirring faintly as he aligned the titanium-tipped cutters with the wire he had deduced to be the linchpin of the circuitry,

"Volatility is often the embyron of great potential," he continued, finally neutralizing the bomb, "the only requirement being the correct catalyst to refine and stabilize its essence."

[hylianengineer]

Okay you know how in cartoons radioactive waste is always stored in big black metal drums? I need you to know those are real.

However the radioactive warning stickers may be smaller and less cool-looking than anticipated.

And they are not generally full of green sludge. It's often, like, contaminated soil, air filters, chemicals, lab waste like paper towels and gloves, glassware, etc. There's also radioactive waste from power plants and weapons manufacturing and stuff, but power plants actually mostly hold their spent fuel onsite (because it is A Pain to move. And when they do move it it won't be in these cylinders, they have their own specially designed containers). I have no idea what the military is up to and I'm sure they like it that way so I've not gone digging - my experience is radiochemical laboratory stuff.

Some of it is also radioactive sources for laboratory, industrial, or medical use - when we calibrate some of our instruments that look for radioactivity and tell us how much of it there is, we have to have a reference sample for comparison (this is true of most lab instruments across fields - back when I did gas lab work, we bought compressed gas cylinders with known concentrations of CO2, methane, and nitrous oxide). And because of the way some of these instruments work, if the source isn't about the same size and density as your samples, it fucks up the math and therefore your results.

This is why we get radioactive sources that are like, a jar of dirt or ground up plants or, once, notably, coffee beans, that intentionally have radioactivity in them - because the source needs to have the same density as the sample. So when we test for radioactivity in soil or vegetation or food, we need those sources for comparison. Apparently the company that makes our sources decided coffee beans were close in density to some of the plants we work with? I don't know why.

Problem is, radioactive sources expire - they get old and the amounts of radioactivity in them decrease and we can't use them for calibrations anymore, especially with certain radioisotopes that decay very quickly. But they're still quite radioactive, way too much to go to a normal landfill. And then we have to dispose of them as radioactive waste.

[thetnclab]

Hospital Equipment Calibration services Delhi

TNC Lab is a leading provider of Hospital Equipment Calibration services in Delhi. With a reputation for precision and reliability, they specialize in calibrating a wide range of medical equipment used in hospitals, ensuring accurate and consistent performance. Their team of skilled technicians utilizes advanced calibration methods and state-of-the-art equipment to maintain the highest industry standards. Through their services, hospitals can ensure the safety and efficacy of their medical instruments, promoting better patient care and compliance with regulatory requirements. TNC Lab's commitment to excellence and prompt service makes them a trusted partner for hospitals seeking accurate calibration solutions in Delhi.

Read More:- https://calibrationservices.home.blog/2023/07/19/how-calibration-impacts-healthcare-cost-efficiency-preventing-expensive-errors/